Orbit B-HYVE 71003 Manuel utilisateur
B-HYVE FLOOD SENSOR
Instruction
Manual
Compatible with other
B-hyve® products
Screw Driver Slot
Welcome to your B-hyve Flood Sensor. This smart sensor detects if
water is present and monitors the surrounding temperature. If water is
detected or there is a temperature fluctuation, a chirp will play and a
notification will be displayed on your phone. Once the problem is fixed,
just reset your sensor and use it again.
Screw Driver Slot
Screw Driver Slot
Screw Driver Slot
LED
Status
Light
INSIDE
CR2032
Battery
Location
Pairing
Reset
Button
MAC ID
Water
Sensors
FRONT BACK
Retrieval
Cord Double-
sided
adhesive
1) Open the B-hyve App
Add the B-hyve Wi-Fi Hub as a new device. The app will walk you through
the rest of the process.
For new users, search apps for “B-hyve” and download the free
Android or iOS app. Create an account to begin setup.
2)Power and Pair Sensor
Remove the plastic strip to activate the battery. Your sensor is now in pairing
mode and will flash a blue light every 5 seconds.
If at any time you need to re-pair, quickly press the on the back
of the sensor 5 times.
Sensors include one Lithium CR2032 battery. Annual battery replacement
is recommended for optimal performance. See the “Replacing the Battery”
section for instructions.
3)Select Sensor Location
Place the sensor in an indoor location within range of your hub. Range is
300 ft without interference. Postition the retrival cord for easy extraction
when placing a sensor beneath heavy objects. Use the double-sided adhesive
to affix a sensor into place in areas where it could be accidentally moved.
If using as a water sensor:
Place the sensor flat on the floor in the lowest part of the area you wish to
monitor.
Ensure the sensor is facing up.
If using as a heat/cold sensor:
Place in the location where you wish to detect changes
in temperatures.
Avoid areas where inconsistent temperatures are common.
(near vents, exhausts, etc.)
The sensor communicates with the hub via Bluetooth; the range
between the sensor and hub will vary depending on the number of walls
and types of obstacles the signal needs to travel through.
Avoid areas where the signal must travel through dirt,
or thick steel barriers.
A A
D D
N N
R R
DRAWN
4)Complete Sensor Setup
Scan for access to a full user manual, videos, and more.
Or visit us at: mybhyve.com
Replacing the Battery
Always completely secure the battery compartment. If the battery
compartment does not close securely, stop using the product, remove the
batteries, and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention. Even used cells may cause injury.
A A
D D
N N
R R
DRAWN
• Insert a flathead screwdriver into the open slot.
• Turn the screwdriver 90º to snap open the cover.
• To remove the battery, lift on the edge of the coin cell
battery using your fingers. DO NOT use a screwdriver
or other metal object.
• Insert a new CR2032 battery at an angle.
• Verify that the + side is up.
• Reinstall the battery cover by snapping it into place.
CAUTION: Dispose of used batteries according to the battery
manufacturer’s instructions.
WARNING: Risk of Fire, Explosion, and Electric Shock.
Replace battery with Hitachi Maxell Ltd, Type CR2032 only.
Use of a different battery has the potential for a risk of fire,
explosion, and electric shock.
WARNING: Do not ingest batteries. Chemical Burn Hazard.
Keep batteries away from children.
WARNING: This product contains a lithium button/coin cell battery.
WARNING: If a new or used lithium button/coin cell battery is
swallowed or enters the body, it can cause severe internal burns and can lead
to death in as little as 2 hours.
Specifications
Sensor
HVIN: FS1
Part No – 71003, 71000, 94319, 96319, 04133
FCC ID:ML6FS1
IC:3330A-FS1
RATING: DC 3.0V
Battery: CR 2032 Lithium (Non-Rechargeable)
Temp Range: 0-70 °C (32-158°F)
Hub
HVIN: BH1G2
Part No – 21008, 94992, 96992
FCC ID:ML6-BH1G2
IC:3330A-BH1G2
Range: 300 ft without interference
Temperature Operating Range: 32°F-104°F (0-40°C)
Storage Temperature: -4°F to 140°F (-20 °C to 60 °C)
Humidity Operating Range: 0–90%
Input: 100-240V ~ 50/60Hz 0.2A
Output: 5V-1.0A
FCC and IC Statement
This device complies with Part 15 of the FCC Rules and Industry Canada
license exempt RSS standards. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
FCC Warning: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Déclaration de FCC et l’IC
Cet appareil est conforme à la section 15 de la Règlementation de la FCC
et la norme RSS d’Industry Canada.
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet
appareil ne doit pas causer d’interférences nuisibles, et (2) cet appareil
doit tolérer toutes les interférences, dont les interférences pouvant
causer un fonctionnement non désiré. Cet appareil numérique de classe
B est conforme à la norme canadienne ICES-003.
Remarque: cet appareil été testé et déclaré conforme aux limites
d’exposition pour les appareils numériques de classe B, selon la section
15 de la Règlementation de la FCC. Ces limites sont conçus pour fournir
une protection raisonnable contre les interférences nuisibles dans une
installation résidentielle. Cet appareil produit, utilise et peut émettre
de l’énergie radio fréquence et, si elle n’est pas installée et utilisée
conformément aux instructions, peut causer des interférences nuisibles
This device meets the FCC and IC requirements for RF exposure in
public or controlled environments. The end user is advised to maintain
a distance of 20 cm from the controller and any personnel to ensure
compliance with RF exposure regulations.
This Class B digital apparatus complies with Canadian ICES-003
• Augmentez la distance entre l’appareil et le récepteur.
• Branchez l’appareil dans une prise sur un circuit différent du circuit sur
lequel le récepteur est branché.
• Consulter le revendeur ou un technicien radio/TV expérimenté pour
obtenir de l’aide.
aux communications radio. Cependant, il n’est pas garantie que des
interférences ne se produisent pas dans une installation particulière.
Si cet appareil cause des interférences gênantes à la réception d’un
signal radio ou de télévision, ce qui peut être déterminé en allumant et
en éteignant l’appareil, l’utilisateur peut corriger les interférences en
suivants une des mesures suivantes :
• Réorientez ou repositionnez l’antenne de réception.
Cet appareil est conforme aux exigences de la FCC et de l’IC concernant
l’exposition aux ondes dans un environnement public ou contrôlé. Il
est conseillé à l’utilisateur final de maintenir une distance de 20 cm du
contrôleur pour assurer la conformité aux réglementations d’exposition
RF. Information de conformité pour le Canada
Autres manuels pour B-HYVE 71003
1
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Orbit Accessoires
