ORACLE LIGHTING OFL-402-LED Manuel utilisateur
OFL-402-LED INSTRUCTIONS
LED Floodlight
1.
Use screw key to open the junction-box
3.
Screw up the knuckle mount into junction-box.
3.27"
3.27"
5.0"
12.44"
PAGE 1 OF 3
O.R.-Revision A: 4/1/20
Caution:
Disconnect AC power before servicing and installation.
All electrical connections must be in accordance with
NEC/CEC or your local code.
PRODUCT DIMENSIONS
2.
Put the wires of lamp into the junction-box.
PRODUCT SPECIFICATION
SAFETY INSTRUCTIONS
1. Equipment should be mounted securely in locations and at heights where it will not be readily subjected to tampering by
unauthorized personnel. 2. Do not mount near gas or electric heaters. 3. Cap unused wires with enclosed wire nuts or other approved
method. 4. Do not use this equipment for anything other than its intended use. 5. The use of accessory equipment not recommended
by the manufacturer will void product listing and warranty and may cause an unsafe condition. 6. Any service on this equipment should be
performed by qualified personnel only. 7. Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.
8. Damaged by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against
corrosive agents such as moisture and condensation and other harmful elements. 9. Electrical connection should be in a dry area unless
adequately sealed. CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING
PRODUCT SPECIFICATION
Input Voltage
120-277 VAC
Input Current
Frequency
50/60 Hz
Rated Power
150W
Suitable For
Wet Location
Note:
1. This fixture should not be used in areas with limited ventilation or high ambient temperature exceeding 45°C. 2. Keep enough length
wires to ensure adjusting angle inhindered. 3. This product series emits high light output. DO NOT look directly into the light emitting
area. Direct exposure to the light over an extended time period may harm eyes 4. Operating ambient temperature range -40°C to 45°C
INSTALLATION STEPS (THREADED KNUCKLE)
14.37" 3.27"
14.5"
7.08"
15.2"
4.05" 11.48"
14.37"
OFL-402-LED INSTRUCTIONS
LED Floodlight
8.
Use hex-key to screw up the hex-screw. Installation completed.
7.
Adjust the lamp into suitable angle.
4.
Use wire-nuts to connect the wires of lamp and junction-box
6.
Use hex-key to screw offthe hex-screw in knuckle mount.
5.
Lock the junction-box with screw key.
1.
Loosen the screw used to fix the upper and the lower mount in rotating
shaft by Hexagon wrench.
3.
Lock the upper and lower brackets by Hexagon wrench.
2.
Rotate the bracket to proper Angle.
INSTALLATION STEPS (SLIP FITTER)
PAGE 2 OF 3
O.R.-Revision A: 4/1/20
OFL-402-LED INSTRUCTIONS
LED Floodlight
3.
Fasten the screw nut clockwise with provided hardware with a wrench.
2.
Make the bracket face tightly to the wall through the thread.
4.
Connect wires.
1.
Mark the position of the fixing holes withflood light light bracket, then
drill the fixing holes. Drive in the bolts to the pre-drilled holes with
thread outside, as the below pic indicate.
5.
Fix the bracket to lamp pole by hexagonal wrench.
4.
Rotate the light to the proper angle and fasten the screws.
6.
Connect wires.
5.
Fasten the screw both sides with allen driver.
INSTALLATION STEPS (YOKE)
Notice: The maximum
diameter of lamp pole
is 2.36in, lamp adjustable
angle is 0-90deg
PAGE 3 OF 3
O.R.-Revision A: 4/1/20
Table des matières
Autres manuels ORACLE LIGHTING Projecteur
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
