Optika CL-14 Manuel utilisateur
Model
CL-14
Accessories Series
INSTRUCTION MANUAL
v 1.0 2017
Page 2
Summary
1. Warning
2. Symbols and conventions
3. Safety Information
4. Intended use
5. Overview
6. Unpacking
7. Assembling
8. Using the illuminator
9. Maintenance
10.Troubleshooting
Equipment disposal
Page 3
1. Warning
This microscope is a scientic precision instrument designed to last for many years with a minimum of mainte-
nance. It is built to high optical and mechanical standards and to withstand daily use. We remind you that this
manual contains important information on safety and maintenance, and that it must therefore be made acces-
sible to the instrument users. We decline any responsibility deriving from incorrect instrument use uses that does
not comply with this manual.
2. Symbols and conventions
The following chart is an illustrated glossary of the symbols that are used in this manual.
CAUTION
This symbol indicates a potential risk and alerts you to proceed with caution.
ELECTRICAL SHOCK
This symbol indicates a risk of electrical shock.
3. Safety Information
Avoiding Electrical Shock
Before plugging in the power supply, make sure that the supplying voltage of your region matches with the
operation voltage of the equipment and that the lamp switch is in o position. Users should observe all safety
regulations of the region. The equipment has acquired the CE safety label. However, users have full responsibil-
ity to use this equipment safely. Please follow the guidelines below, and read this manual in its entirety to ensure
safe operation of the unit.
4. Intended use
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
Page 4
5. Overview
LOCKING
SCREWS
FIXING RING
SOCKET FOR
POWER SUPPLY
LIGHT INTENSITY
KNOB
LED
ILLUMINATOR
ON/OFF
SWITCH
6. Unpacking
Extract the illuminator from its packaging. Keep it away from thinners, chemical vapors and excessive moisture.
Avoid high temperature environments, the direct sun light and excessive vibrations, which could aect the
performance of the instrument.
Operating environment
Temperature: 10 - 36°C (50 – 96.8°F)
Relative humidity: 0 – 85% up to 30°C (86°F)
Page 5
Place the illuminator on the
xing ring, using the three
locking screws (Fig.4).
► When installing on
LAB-series: remove
the reected light
illuminator before
installing the round
light illuminator
(Fig. 2-3).
Connect the power supply
to the wall socket (Fig.5)
7. Assembling
8. Using the illuminator
Fig.1
Fig.3Fig.2
Fig.4 Fig.5
Fig.6
Installing the illuminator
Avoid disassembling the
instrument
Screw the xing ring on the
bottom of the Stereo head
(Fig.1).
► The illuminator can be
used on the following
intruments series:
SZN, SZM, LAB.
Do not disassemble the
instrument. This entails the
cancellation of the warranty
and may cause malfunction.
• Use ON/OFF switch ①
to turn the LEDs on.
• Use the knob ②to
adjust the light intensity
(Fig.6).
The power supply should be used only on network sockets
equipped with adequate grounding.
Always disconnect the power supply from the illuminator when
not in use for long time, while you clean it or when you perform
any maintenance.
①②
Page 6
9. Maintenance
Microscopy environment
This microscope is recommended to be used in a clean, dry and shock free environment with a temperature of
5°-40°C and a maximum relative humidity of 75 % (non condensing). Use a dehumidier if needed.
To think about when and after using the microscope
• The microscope should always be kept vertically when moving it and be careful so that no
moving parts, such as the eyepieces, fall out.
• Never mishandle or impose unnecessary force on the microscope.
• Never attempt to service the microscope yourself.
• After use, turn o the light immediately, cover the microscope with the included
dust-cover, and keep it in a dry and clean place.
Electrical safety precautions
• Before plugging in the power supply, make sure that the supplying voltage of your region
matches with the operation voltage of the equipment and that the lamp switch is in o-
position.
•
Users should observe all safety regulations of the region. The equipment has acquired
the CE safety label. However, users do have full responsibility to use this equipment safely.
Cleaning the optics
• If the optical parts need to be cleaned try rst to: use compressed air.
• If that is not sucient: use a soft lint-free piece of cloth with water and a mild detergent.
• And as a nal option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.
Note: ethanol and ether are highly ammable liquids. Do not use them near a heat source, near sparks or
near electric equipment. Use these chemicals in a well ventilated room.
• Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage the
optics.
• Do not disassemble objectives or eyepieces in attempt to clean them.
For the best results, use the OPTIKA cleaning kit (see catalogue).
If you need to send the microscope to Optika for maintenance, please use the original packaging.
10. Troubleshooting
Review the information in the table below to troubleshoot operating problems.
PROBLEM CAUSE SOLUTION
1. Optical System
LED does not light. Power cord is unplugged. Plug power cord into the power outlet.
The main switch is on “O” position Set main switch on “I” position.
Light too dim on the sample Intensity set too low. Adjust the intensity knob.
Page 7
Equipment disposal
Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating
to the reduction in the use of hazardous substances in electrical and electronic equipment and waste disposal.”
The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be
collected separately from other waste.
The separate collection of this equipment at the end of its lifetime is organized and managed by the producer.
The user will have to contact the manufacturer and follow the rules that he adopted for end-of-life equipment
collection.
The collection of the equipment for recycling, treatment and environmentally compatible disposal, helps to prevent
possible adverse effects on the environment and health and promotes reuse and/or recycling of materials of the
equipment.
Improper disposal of the product involves the application of administrative penalties as provided by the laws in force.
Modello
CL-14
Serie Accessori
MANUALE D’ISTRUZIONI
v 1.0 2017
Pagina 10
Sommario
1. Avvertenze
2. Simboli e convenzioni
3. Informazioni di sicurezza
4. Applicazioni d’uso
5. Lista accessori e ricambi
6. Panoramica
7. Disimballaggio
8. Assemblaggio
9. Uso del microscopio
10.Manutenzione
11. Risoluzione problemi
Misure ecologiche
Table des matières
Langues :
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
