OPTICOM 764 Manuel utilisateur

OpticomGPS System

Intersection Equipment

OpticomGPS System

OpticomIR System

Model 764 Phase Selector

Installation Manual November 2012

Intersection Equipment Installation Instructions

Table of Contents

1About This Manual........................................................................................................................... 5

1.1 Intended Use ............................................................................................................................. 5

1.2 Technical Support...................................................................................................................... 5

1.3 Safety Messages and Safety Labels.............................................................................................. 5

1.4 Safety Considerations................................................................................................................. 5

1.4.1 Personal Safety Equipment and Clothing .............................................................................. 5

1.4.2 Work Zone Traffic Control................................................................................................... 5

1.4.3 Electric Shock...................................................................................................................... 6

1.5 Disposal of Device..................................................................................................................... 6

1.6 FCC Statement ........................................................................................................................... 6

2Description...................................................................................................................................... 7

3Radio/GPS unit Installation............................................................................................................ 10

3.1 Model 1010 Radio/GPS unit mounting Location Considerations................................................ 10

3.1.1 Model 1010 Radio/GPS Unit Installation............................................................................ 14

3.1.2 Model 1012 Radio Installation........................................................................................... 16

3.1.2.1 Model 1050 Antenna mounting................................................................................... 17

3.1.2.2 Radio mounting .......................................................................................................... 18

3.1.2.3Radio/GPS Unit Cable Terminations ............................................................................ 18

4Powering the Phase Selector .......................................................................................................... 20

4.1 Powering on 120 VAC 60 Hz................................................................................................... 20

4.2 Powering on 24VDC................................................................................................................ 20

5Phase Selector Installation in Controller Cabinets with Existing Card Racks ................................... 21

5.1 Potential for Electrical Shock.................................................................................................... 23

6Phase Selector Installation in NEMA Cabinets using 760 or 1040 Card Rack .................................. 24

6.1 Model 1045B Card Rack.......................................................................................................... 27

6.1.1 Model 1045 in IR Operation.............................................................................................. 27

7Model 755 Four Channel Adapter Card and Other Model Card Racks............................................ 28

8Radio/GPS Cable Connection ........................................................................................................ 29

9Model 768 Auxiliary Interface Panel (AIP) ..................................................................................... 30

9.1 Auxiliary Interface Panel Installation......................................................................................... 31

9.2 Green Sense Wiring ................................................................................................................. 33

9.3 Confirmation Light Wiring........................................................................................................ 34

9.3.1 Confirmation Light Wiring with Load Switch Interface........................................................ 34

9.3.2 Confirmation Light Wiring with Electromechanical Relay Interface ..................................... 36

9.4 Connecting existing harnesses to the model 768 auxiliary interface panel ................................. 38

9.4.1 Existing GPS installation using model 1035 auxiliary harness ............................................. 38

9.4.2 Existing GPS installation using model 1030 auxiliary interface panel .................................. 38

9.4.3 Existing IR installation using a model 757 auxiliary harness ................................................ 38

9.4.4 Existing IR installation using a model 758 auxiliary interface panel..................................... 38

9.5 Additional Output Connections................................................................................................ 39

9.5.1 Turn Signal Dependant Operation Example........................................................................ 42

10 Infrared (IR) Operation............................................................................................................... 43

11 Phase Selector Pin Index............................................................................................................. 44

12 Communication Ports ................................................................................................................. 46

12.1 Ethernet Port ............................................................................................................................ 46

12.1.1 Ethernet indicators.......................................................................................................... 46

12.2 USB Port.................................................................................................................................. 47

12.3 RS-232 Communication Ports................................................................................................... 47

Intersection Equipment Installation Instructions

12.3.1 RS-232 COM Port on the Rear Edge Connector............................................................... 49

12.3.2 RS-232 COM Ports on the Auxiliary Interface Panel ........................................................ 50

13 Phase Selector Indicators, Display and Switches ......................................................................... 51

13.1 Indicators................................................................................................................................. 51

13.2 Display and Switches............................................................................................................... 53

13.2.1 Manual Test Calls........................................................................................................... 54

13.2.1.1 Turn Signal Sub Menu................................................................................................. 54

13.2.2 Error listing..................................................................................................................... 56

13.2.3 Set Range....................................................................................................................... 56

13.2.4 Detector Function Test ................................................................................................... 57

13.2.5 IP Address Reset............................................................................................................. 57

13.2.6 Password Override......................................................................................................... 57

13.2.7 Erase Logs ...................................................................................................................... 57

13.2.8 Reset All Parameters to Default....................................................................................... 57

13.2.9 Standby Mode................................................................................................................ 57

14 Checkout.................................................................................................................................... 58

15 Troubleshooting.......................................................................................................................... 58

15.1 Fuse Locations ......................................................................................................................... 58

15.2 Troubleshooting Tables............................................................................................................ 59

16 Maintenance............................................................................................................................... 63

17 Setup and Testing ....................................................................................................................... 63

Appendix A: Opticom Output Connection Worksheet (High Priority only).......................................... 64

Appendix A1: Opticom Output Connection Worksheet (High & Low Priority)..................................... 65

Appendix B: Driving a Relay from a Phase Selector ............................................................................. 66

Appendix C Gate Opener Card Rack .................................................................................................... 68

Gate Opener Card Rack Installation................................................................................................... 69

Gate Opener Relay Outputs ........................................................................................................... 71

Intersection Equipment Installation Instructions

1About This Manual

Please read, understand, and follow all safety information contained in these instructions before

installing the system equipment. Save this installation manual and keep it near the equipment.

If you are unsure about any part of this installation or of the potential hazards discussed, please contact your

supervisor immediately.

1.1 Intended Use

The system is intended to assist authorized priority vehicles through signalized intersections by providing

temporary right-of-way through vehicle operator interface to the system and through the use of common

traffic controller functions. GTT has not evaluated this product for use in any other application.

1.2 Technical Support

If you have questions about the system, its use, or operation, please contact your dealer or call the GTT

Technical Service department at 1-800-258-4610.

1.3 Safety Messages and Safety Labels

We include safety messages and labels in this manual to help you protect your safety and the safety of

others.

Please read these messages before proceeding with the installation.

1.4 Safety Considerations

Please consider the following safety issues before beginning the installation of the Opticom™ System

intersection equipment.

Although we have compiled this list of common safety considerations, it should not be considered as

complete. It is not intended to take the place of your good judgment, training, and experience.

1.4.1 Personal Safety Equipment and Clothing

Personal safety equipment and clothing including high visibility vests, hard hats, gloves, electrical shock or

electrocution protection clothing and equipment, safety shoes, safety glasses, face shields, goggles, and

hearing protection devices are just some of the items available to you.

Choose the right equipment for the job. If you are unsure of which safety equipment is recommended or

appropriate for the job, ask your supervisor or foreman.

1.4.2 Work Zone Traffic Control

Proper control of vehicle traffic is important during many procedures. When you switch the traffic

controller to and from the flash mode we recommend that you have people trained in manual traffic

control, such as police officers, assist you.

When you install devices that require you to position vehicles, equipment, or people in or

near the roadway, it is important that you use appropriate work zone traffic control techniques,

equipment, and procedures. Sometimes you may have to work on or near the roadway and these same

techniques, equipment, and procedures should be used for your protection.

If you are unsure of which procedures are recommended or appropriate for the job, ask your supervisor

or foreman.

Intersection Equipment Installation Instructions

1.4.3 Electric Shock

The possibility of electrical shock exists when installing intersection equipment, since connections must be

made to open terminals within the traffic control cabinet which may have 120 VAC present. Follow proper

work procedures and read and understand the safety messages in this manual.

As a trained installer of electrical equipment you are aware of the dangers associated with installation of

electrical devices. Always be sure that the power to the equipment, and all associated equipment, is turned

off before beginning any procedure. Use the equipment, techniques, and procedures that you learned

during your training or apprenticeship or other electrical industry recognized safety procedures.

If you are unsure of which techniques, procedures, and protective equipment are recommended or

appropriate for the job, ask your supervisor or foreman.

1.5 Disposal of Device

Please dispose of the device in accordance with all local, state, and federal laws and regulations.

1.6 FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interferences when the equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. If operation of this

equipment in a residential area causes harmful interference, the user is required to correct the interference

at their own expense.

*The method of using the components of the Opticom GPS system may be covered by one or more of US Patent

Numbers 5539398, 5926113, 5986575, 6243026.

Figure 1-1 FCC label Locations

Intersection Equipment Installation Instructions

2Description

This section provides a general description of the Opticom™ GPS system and a detailed description of the

intersection equipment.

Opticom GPS System

The Opticom GPS system assists authorized priority vehicles through signalized intersections by

providing temporary right-of-way through the use of common traffic controller functions.

The Opticom GPS system consists of the following matched components:

Vehicle Equipment Components

•Radio/GPS unit containing a GPS receiver and a 2.4 GHz transceiver

•Radio/GPS antenna

•Vehicle Control unit

Intersection Equipment Components

•A traffic pole mounted Radio/GPS unit containing a GPS receiver with antenna and a 2.4 GHz

transceiver with antenna (Model 1010)

•Or a Traffic Cabinet mounted Radio/GPS unit containing a GPS receiver and a 2.4 GHz transceiver

(Model 1012) with a Radio/GPS antenna (Model 1050)

•Phase Selector (Model 764)

•Card Rack/Input File (Model 760)

•Auxiliary Interface Panel (Model 768)

Operation Description

The vehicle equipment is mounted on the priority vehicle. Its GPS receiver acquires position information

from the constellation of GPS satellites. This information is used to compute the location, speed, and

heading of the vehicle. This information, along with a priority request, ID information and the state of

the vehicles turn signal, is broadcast using the 2.4 GHz transceiver.

The intersection equipment receives the radio transmission from the vehicle equipment. The intersection

equipment then compares the information being received from the vehicle to the parameters stored in the

intersection equipment’s memory. If the vehicle is heading toward the intersection in a predefined

approach corridor, is requesting preemption and has met all other programmed parameters, the

corresponding phase selector output is activated. This output is connected to the traffic controller

preemption input. When activated, the controller cycles to grant a green light to the requesting vehicle or

holds the green allowing the vehicle to pass through the intersection.

The card rack/input file provides the power and logic wiring for the phase selector, which plugs directly

into a slot in the unit.

The auxiliary interface panel provides additional connection for monitoring green phases and also provides

additional outputs.

Intersection Equipment Installation Instructions

Intersection Equipment Details

The Opticom™ GPS System intersection equipment has two styles of Radio/GPS units available.

The first is the Model 1010, which is a compact, weather-resistant, Radio/GPS unit containing a GPS receiver

with antenna and a 2.4 GHz transceiver with antenna. This model is typically mounted on a traffic pole near

the traffic cabinet.

The second is the Model 1012 Radio/GPS unit, which contains a GPS receiver, a 2.4 GHz transceiver and a

separate Radio/GPS antenna. This model is mounted in the traffic cabinet with the antenna mounted on the

roof of the cabinet.

Both models of the Radio/GPS unit are connected to a phase selector via an 11-conductor radio/GPS cable.

The phase selector can be installed directly into an input file of a traffic controller equipped with priority

phase selection software. The phase selector can also be installed directly into virtually any other traffic

controller equipped with priority phase selection inputs and related software.

When input file space is not available in the traffic cabinet, a card rack is required.

The phase selector processes the signal from the radio/GPS unit and activates outputs which are connected

to the preemption inputs on the traffic controller. There are four channel outputs accessible on the rear

connector of the phase selector and up to 12 additional channel outputs accessible on the front of the phase

selector.

Each channel output delivers a constant output for high priority activation, and a pulsed output for low

priority activation. A high priority signal received on a channel will override any low priority activation. In

certain modes of operation, outputs may be activated that are dependent on the state of the requesting

vehicle’s turn signal. Another mode provides separate outputs for high priority and low priority. The use of

an auxiliary interface panel is required to access these additional modes and outputs.

Figure 2-1 shows the intersection components including the phase selector, card rack, input file, auxiliary

interface panel, and the wiring harnesses and cables. The 9-pin harness connects the card rack to the traffic

controller. Various communication ports are available to connect the phase selector to a PC or to remote

communication equipment. Additional communication connections are available on the auxiliary interface

panel. The auxiliary interface panel cable connects the phase selector to the auxiliary interface panel. The

radio/GPS cable connects the phase selector to the intersection radio/GPS unit.

NOTE: Illustrations and connections to the traffic controller may not be exactly as shown or described in

this manual. Refer to the controller wiring diagram for correct terminal connections.

Intersection Equipment Installation Instructions

Figure 2-1 Intersection Components

Intersection Equipment Installation Instructions

3Radio/GPS unit Installation

This section describes the installation of the radio/GPS unit. There are two models of the radio/GPS unit.

See section 3.2 for details on installing the Model 1012 Radio/GPS unit.

3.1 Model 1010 Radio/GPS unit mounting Location Considerations

Read and understand the following precautionary paragraphs before starting the installation.

•The Model 1010 radio/GPS unit should be mounted in a location that has an unobstructed view of all

approaches out to a distance of 2500 feet (762m).

•Blockage of approaches by things such as bridges, buildings, walkways, and trees should be avoided.

•The Model 1010 radio/GPS unit is usually mounted to the mast arm or span wire pole nearest the traffic

controller cabinet. If an appropriate mounting location on a mast arm or span wire pole is not available,

you can mount the unit to a span wire. Try to use a signal head or sign mount to minimize sway.

•The Model 1010 radio/GPS unit should be mounted level and as high as possible. Do not mount the

unit upside down.

•The Model 1010 radio/GPS unit should have an unobstructed view of at least 50% of the sky.

•The mounting location should be such that the cable run from the radio/GPS unit to the phase selector

(located in the traffic controller cabinet) is no more than 250 feet (76m).

•The radio/GPS cable may be run through conduit or attached to a messenger wire. The cable should

not be suspended unsupported.

•The Model 1010 radio/GPS unit should be oriented such that the cable retainer is facing an area from

which vehicles will NOT be approaching. See Figure 3-1.

•Do not paint the Model 1010 radio/GPS unit cover. Metals or metal oxides in the paint may interfere with

GPS reception and/or radio reception/transmission.

•Do not modify the radio/GPS unit circuitry. There are no user-serviceable parts inside.

IMPORTANT NOTE

Modifying the radio/GPS unit may seriously

damage the equipment and void the warranty.

Do not attempt to modify the radio/GPS

circuitry in any way. Modifying the radio and/or

antenna in any way may cause the radio to

violate FCC/IC requirements.

REMARQUE IMPORTANTE

La modification du système radio/GPS risque

d’endommager sérieusement le matériel et

d’annuler la garantie. Ne pas tenter de modifier

les circuits du système radio/GPS de quelque

façon que ce soit. En modifiant le système radio

et/ou l’antenne de quelque façon que ce soit, la

radio risque de ne plus répondre aux exigences

de la FCC/IC.

Table des matières

Autres manuels OPTICOM Équipement d'enregistrement

OPTICOM

OPTICOM CC03-IP2MVFIR Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien