Ops-Core RAC Manuel utilisateur

RAC™HEADSET

Operator’s Manual

OM101116-00 REV. C

Compatible with: FAST®Maritime, FAST Ballistic High Cut,

FAST Carbon, and FAST Base Jump Helmets

RAC HEADSET

Operator’s Manual

Headset Features

Headset Components

Included / Optional Items

Preparing Headset for Use

Installing Batteries

Attaching Headset to Helmet

Attaching Pile Fasteners

Moving the Microphone

Donning and Dofng Helmet with Headset

Understanding Headset Positions

Basic Donning

Using Ventilation Mode

Dofng

Using Wireless Earbuds

Headset Functions

Maintenance

Operator Notes

RAC HEADSET

Headset Features

•3D Hearing Technology (3DHT)

By coupling a patented ear simulator design with binaural audio and advanced audio processing the RAC

Headset delivers hear-through audio that accurately preserves azimuth and elevation cues to provide

situational awareness. Smooth compression algorithms eliminate “clipping.”

•FAST ARC Rail Attachment

The RAC Headset attaches to the rear of the FAST ARC Rails leaving the top portion of the rails free for

mounting accessories, such as lights, cameras, etc.

•Noise-Cancelling Microphone

Mounts to left or right earcup.

•Integrated Microphone Mounting & Connection Point

Accepts mask microphones with U-173/U standard plug.

•Arm Articulation/Latch

Ventilate mode allows the ear cups to be set in ready position, near, but not pressing on the user’s head.

•Single Point Gimbal Attachment

360˚ adjustment instead of conventional adjustment systems.

•On/Off/Volume/Balance Control

Provides operator full control to personalize the listening experience to suit individual needs. Optional

Speaker/Ear Plug Switch used with Inductance Driver System to switch between speaker and earplug.

•Ear Cushions

High performance to ergonomically t the head geometry, providing a better seal and increased noise

attenuation.

•Streamlined Stowage

Earcups rotate to the rear of helmet when not in use, creating a very low prole.

•Quick-Release Downlead Connection

Helmet/headset can be disconnected from the downlead, allowing users to easily remove the helmet as

there are no excess cables to consider.

•Inductance Receiver Earplug

Un-tethered double-layer hearing protection provides noise attenuation in excess of typical Active Noise

Reduction (ANR) equipped headsets. Earplugs are battery-free.

•Weight

1.1 lbs (500 g) base version

1.2 lbs (545 g) with earplug option

•Immersible

IP-67 immersible

IP-68 immersible to 3 m for short durations

•Environmental

Tested to MIL-STD-810G

•EMl

Tested to MIL-STD-461E

•Export Classication

EAR-99

•Available Colors

Tan, Black, Green, and Gray

HEADSET COMPONENTS

Cable Guides

Cable

Earcup

Hear-Through

Microphones

Ear

Seals

Earcup

Battery

Compartment

Battery

Compartment

Volume / Function

Buttons

Mic Boom

Attachments

Points

Boom Microphone

Pivot

Arm

Button

Pivot

Arm

Button

INCLUDED / OPTIONAL ITEMS

Items Included with Headset:

•(2) AAA Batteries (to install into earcups)

•Pile Fasteners (to attach to helmet for cable stowage)

•Cable Loop (for cable stowage)

•Utility Pouch (to store headset)

Optional Items (Specify When Ordering Headset):

•Earbuds (wireless and battery-free)

•Foam tips for use with earbuds (three sizes: Standard, Slim, and Large)

(2) AAA Batteries Pile Fasteners Cable Loop

Foam Tips

Earbuds

Utility Pouch

PREPARING HEADSET FOR USE

To prepare the headset for use, you will:

1. Install the AAA batteries (one in each earcup)

2. Attach the headset to the ARC Rails on the helmet

3. Attach the pile fasteners to the helmet

4. Move the microphone to the other earcup (if needed)

Installing the Batteries:

NOTE: Also follow the applicable steps below to replace the batteries.

1. Remove the (2) AAA batteries from the packaging.

2.Pry the ear seal away from the earcup by pressing the tab at the bottom.

3.Insert the battery into the battery

compartment making sure to align the

battery so that the polarity marks (+ and -)

on the battery align with the corresponding

markings in the earcup battery

compartment.

NOTE: Always replace batteries

from both earcups as a set, do not

mix-and-match batteries.

CAUTION: When performing Step 2, be careful not to damage the

rubber seal in the groove on the underside of the earseal.

INSTALLING BATTERIES

Positive

Negative

Rubber Seal

INSTALLING BATTERIES

4.Reinstall the ear seal, ensuring that it is securely snapped to the

earcup all around the edges.

CAUTION: Be careful not to pinch the ear seal in the

groove when snapping it closed.

5.Repeat Steps 2-4 to install the other battery into the other earcup.

NOTE: Remove batteries before storing RAC Headset

for extended periods of time.

Table des matières

Autres manuels Ops-Core casque

Ops-Core

Ops-Core AMP Manuel utilisateur

Manuels casque populaires d'autres marques

Sena

Sena SMH10 Manuel utilisateur

IASUS

IASUS Stealth IA-NT4-BASIC-BT Manuel utilisateur

Sennheiser

Sennheiser EPOS ADAPT 230 Manuel utilisateur

Doro

Doro Flexus HS2005 Manuel utilisateur

GE 98971 Manuel utilisateur

Hama

Hama 00184070 Manuel utilisateur

Plantronics

Plantronics Blackwire 3200 Series Manuel utilisateur

Blue Tiger

Blue Tiger Advantage PLUS Manuel utilisateur

Jawbone

Jawbone Icon Manuel utilisateur

Jabra

Jabra FR 20 Manuel utilisateur

Roxcore

Roxcore Flow A+ Manuel utilisateur

Turtle Beach

Turtle Beach XP 510 Manuel utilisateur

Philips

Philips SHB6101 Manuel utilisateur

Jabra

Jabra PRO 9460 Duo Manuel utilisateur

HyperX

HyperX HyperX Cloud Flight Manuel utilisateur

Bose

Bose MIE2 Mobile Manuel utilisateur

Jabra

Jabra Steel Manuel utilisateur

HyperX

HyperX cloud ii Manuel utilisateur