Opitec Hobbyfix Cube Manuel utilisateur

D108465#2

Please Note

The OPITEC range of projects is not intended as play toys

for young children.They are teaching aids for young people

learning the skills of Craft, Design and Technolo- gy.These

projects should only be undertaken and tested with the

guidance of a fully qualified adult. The finished projects are

not suitable to give to children under 3 years old. Some

parts can be swallowed. Dan- ger of suffocation!

108.465

„Cube“

Labyrinth in 3 layers

(acrylic )

Parts list

Quantity Size(mm) Description Part No

Acrylglasstreifen 2 2x90x190 layers 1

Pine strip 6 10x20x250 frame , labyrinth 2

Steel ball 1 ø10 3

Necessary tools

Pencil, ruler

Wood glue

Fine saw, mitre block

Pillar drill 15mm diameter.

Sand paper / wet dry paper

Warning!

This product con-

tains small parts that

can be swallowed

There is a danger of

choking

2D108465#1

Instructions

1. General: Using the materials given the cube can be made to the instructions or your own design ( The full size

patterns are on page 5 )

Note:

The holes are 10mm diameter. The pine strips for the labyrinth must have a gap of 11mm.

2. Check the design for your labyrinth carefully before starting to cut any wood.

Make up a cutting list for the pine strips.

3. Mark out and saw four squares 90 x 90 mm from the acrylic ( See diagram 3 )

4. Mark out the position of the hole on the acrylic sheet. 1

5. Drill the 15mm hole with a pillar drill ( Drill in two steps rst use a smaller drill )

(Please take care to adhere to the safety rules when drilling and use a scrap piece of wood as an underlay)

Note!

You can drill both top and bottom holes at once. The position of the second hole is marked on the plan with a bro-

ken line.

6. Cut the pine strip according to your list ( Take care with the quantity of material supplied )

7. Sand the pine strips

8. Glue the strips on the acrylic ( See diagram 3+4 ) Use UHU all purpose

or a similar glue

Note!

Take care with the position of the holes

9. Once dry you can assemble and glue the layers together. The best way is layer 2 with layer 3 & then layer 1 with the

lid. Leave to dry and then glue layer 1 to layer 2

Hinweis: Position der einzelnen Ebenen beachte, dass nicht 2 Bohrungen übereinander liegen!

10. Den Cube außen versäubern und evtl. die Holzäche mit Lack, Wachs usw. behandeln.

Viel Spaß mit dem Labyrinth-Cube!

Layer 1

Lid Layer 2

Layer 3

D108465#2

18,5

Ø 15

Lid and bottom for all the layers

Layer 1

4D108465#1

20 50

Layer 2

Layer 3

D108465#2

Anlage 1

Note:The patterns have 10x 10mm squares! Make sure that the labyrinth strips have a space of 11mm and that the holes in the

layers are not larger than 10mm diameter.

Stückliste:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Opitec Jouet

Opitec

Opitec Solar Auto with gearbox Manuel utilisateur

Opitec

Opitec Dragonfly 102.894 Manuel utilisateur

Opitec

Opitec 102.320 Nummer II Manuel utilisateur

Opitec

Opitec 114.066 Manuel utilisateur

Opitec

Opitec 117167 Manuel utilisateur

Opitec

Opitec Hobbyfix Stiletto 105.755 Manuel utilisateur

Opitec

Opitec 104.689 Manuel utilisateur

Opitec

Opitec Hobbyfix 113.727 Manuel utilisateur

Opitec

Opitec Wasp Manuel utilisateur

Opitec

Opitec 111.714 Manuel utilisateur

Opitec

Opitec Hobbyfix Cloud Manuel utilisateur

Opitec

Opitec Running worker with wheelbarrow Manuel utilisateur

Opitec

Opitec Windflyer II Manuel utilisateur

Opitec

Opitec Hobbyfix 101.706 Manuel utilisateur

Opitec

Opitec Recycling Rowing Boat Manuel utilisateur

Opitec

Opitec 112.994 Manuel utilisateur

Opitec

Opitec MANITOU 101.200 Manuel utilisateur

Opitec

Opitec Hobbyfix Manuel utilisateur

Opitec

Opitec Rattle Snake Manuel utilisateur

Opitec

Opitec 114.033 Manuel utilisateur

Opitec

Opitec 115.305 Manuel utilisateur

Opitec

Opitec 120.852 Manuel utilisateur

Opitec

Opitec 113.141 Manuel utilisateur

Opitec

Opitec Wind Machine Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur