Installation
1. Power up you Ontech master unit.
2. Deactivate the alarm function in the master unit by sending an SMS with the
content:
ABCD*7*0# (ABCD is the PINCODE you have decided, see your manual for
the master unit.)
3. Remove the cabinet from the Alarmbox by unscrew the screw and fold up
the upper part.
4. Set the unit ID number
a. Factory setting is ID 2. If you have two or more Alarmboxes you sure want
to know which one that is sending the alarm. DIP-switch 6, 7 and 8 is used
to set ID number according to the table below.
ID Switch 6 Switch 7 Switch 8
ID2 OFF OFF ON
ID3 OFF ON OFF
ID4 OFF ON ON
ID5 ON OFF OFF
ID6 ON OFF ON
ID7 ON ON OFF
ID8 ON ON ON
5. Set the radio channel
a. Normally you do not have to change this. If two or more Ontech system
is working close to each other or if there is other types of interference
another radio channel can be set. DIP-switch 2, 3, 4 and 5 is used for this
purpose. They can be set in any position but most important that the
setting is same on master unit and all connected Alarmboxes.
6. Attach the bottom part of the cabinet with two screws at the place you want.
If the magnetic switch shall be used the magnet is placed along the left
side of the Alarmbox (se figure) and is centred along the side. The distance
between the Alarmbox and the magnet must not be more than 3 mm.
7. Connect alarm sensors
a. The built-in magnetic switch
If the built-in magnetic switch shall be used at for example a door or win-
dow you must disconnect the cable jumper between the NC and GND
terminal.
b. Alarm sensor with Normally Closed (NC) operation
The relay output from the alarm sensor is normally closed. When alarming
the circuit is opened. Many PIR devices is constructed in this way.
Disconnect the cable jumper on the terminals NC and GND connectors
and connect instead the two cables from the alarm sensor.
c. Alarm sensor with Normally Open (NO) operation
The relay output from the alarm sensor is normally open. When alarming
the circuit is closed. For example level guards are constructed in this way.
Connect the cables in the NO and GND connectors on the terminal. NB,
The cable jumper should NOT be removed.
8. Take away the plastic insolation strap from the battery. Now the red LED is
blinking a couple of times.
9. Press the microswitch. The red LED shall now single blink or double blink one
or two times. If it is a double blink an alarm sensor is active.
If it is single blinking or double blinking three times it means that the unit has
no connection with the master unit. Control the setting of the radio channel
and control/adjust the distance between the Alarmbox and the master unit.
10. Attach the cover of the cabinet and fix it with the screw. If you have con-
nected an alarm sensor with wires it is necessary to make a hole for it in the
lower left corner.
11. Press the button on the main unit at least two times in order to acknowledge
the alarm sent when the Alarmbox was powered.
12. Make a status request to the main unit by sending an SMS with the content
ABCD#8#. You shall receive a reply SMS with information of which units that
are connected to the master unit. For interpreting the SMS, se next side.
13. Activate the alarm function on the master unit by sending an SMS with the
content ABCD#7*1#.
14. Activate the alarm sensor and check that all telephones on the alarm list
receives the Alarm SMS.
Introduction
• Ontech Alarmbox 9012 is a wireless device which send alarms to Ontech
GSM 9020 and Ontech GSM 9030 via a short range radio at frequency 2,4
GHz. Ontech GSM 9020 and Ontech GSM 9030 will in this manual be called
the master unit.
• The Alarmbox is sending an alarm message when one of the alarm inputs;
NO (Normally Open) eller NC (Normally Closed) has been activated. A
built-in magnetic switch is connected in parallel with the NC input. There
is also a sabotage alarm, a microswitch is activated when the cabinet cover
is removed.
• The Alarmbox has a built-in temperature sensor and in all messages from
the unit the temperature is reported.
• Up to seven Alarmboxes can individually be connected to each main unit.
One or more Ontech Relay 9010 in your Ontech system decreases the
number of Alarmbox you can connect. Highest total sum of Ontech Relay
9010 and Alarmbox units is seven.
• Operating range is at least 30 meters in free field. Construction and material
in houses affect the indoor operating range.
• In this manual all commands are described as SMS commands.
• Ontech also has developed apps for Android system and Iphones. Inside
those apps the function is described. Search on Ontech control on Google
Play or App stor. Or use the QR codes below.
Idle operating mode
The Alarmbox is sending status information at start up and then every twenty
minutes. This information is stored until next status update or longest 60
minutes. This means that if the Alarmbox is disconnected or stops working it will
take maximum 60 minutes until it disappears from SMS messages.
Google Play App store
1 8765432
ON
+
NC NO GNDGND
LED
Magnet
Terminal
Microswitch
DIP-switch
Battery
Position of the components
Above the unit is shown without the cover of the cabinet. The figure is simplified
in order to easy show the position of the components.
Ondico AB is not responsible for damages that may occur due to incorrect use or
if the product does not work as desired.
Welcome
Thank you for choosing to update your Ontech GSM system with an Alarmbox.
We hope that this manual will help you to easy install the unit and that you will
be satisfied with the unit and its functions.
ments on the unit and this manual.
