Onfloor Striker 2010 Manuel utilisateur
Operators Manual
STRIKER 2010
PN 236683 - Striker 2010 Parts List - Printed in USA 03/18/08
TABLE OF CONTENTS
1
PAGE
14
SQUEEGEE BLADE REPLACEMENT 15-16
SQUEEGEE ADJUSTMENT 16
BATTERY MAINTANENCE 17
TRANSPORTING MACHINE 17
STORING MACHINE 17
LED FAULT CODES 18
SPECIFICATIONS 18
GENERAL MACHINE DIMENSIONS 18
BATTERIES 18
SOLUTION DELIVERY SYSTEM 19
BRUSH SYSTEM 19
SOLUTION RECOVERY SYSTEM 19
DRIVE SYSTEM 19
SOUND RATING 19
SAFETY PRECAUTIONS 2
OPERATION 3
OPERATOR RESPONSIBILITY 3
MACHINE COMPONENT LOCATIONS 4
CONTROL PANEL SYMBOLS 5
UNCRATING MACHINE 5
INSTALLING BATTERIES 6
ATTACHING SQUEEGEE 7
BRUSH PAD SELECTION 8
BRUSH PAD INSTALLATION 9
FILLING THE SOLUTION TANK 9
MACHINE OPERATION 10-11
DRAINING TANKS 11-12
CIRCUIT BREAKER FUSES 12
BATTERY METER 13
HOURMETER 13
CHARGING BATTERIES 13-14
MAINTENANCE
SAFETY PRECAUTIONS
2
90-88012
Open FlamesAway.
When Charging.
Keep Covers Open
Explosion Or Fire
Hydrogen Gas.
Batteries Emit
Keep Sparks And
WARNING
Can Result.
90-88042
MaterialsIn Tank(s).
WARNING
Can Cause Explosion
Do NotUse Flammable
Flammable Materials
Or Fire.
Can Cause Explosion
WARNING
WARNING
Flammable Materials
OVERLAY SOLUTION WARNING
Do Not Use Flammable
Or Fire.
Materials In Tank(s).
Can Result.
Keep Sparks And
Hydrogen Gas.
Explosion Or Fire
Keep Covers Open
When Charging.
Open Flames Away.
Batteries Emit
WARNING
WARNING
DECAL, CHARGING WARNING
90-88013
DoNot Pick Up
ExplosionsOr Fire
WARNING
CanCause
ReactiveMetals
MaterialsOr
Flammable
Flammable
Materials Or
Reactive Metals
Can Cause
Explosions Or Fire
Do Not Pick Up
WARNING
DECAL, PICKUP WARNING
FOR SAFETY
ReadManual
BeforeOperating
Machine
90-88017
DECAL, READ MANUAL
FOR SAFETY
Machine
Before Operating
Read Manual
The safety labels appear on the machine in
the locations indicated. If these or any label
becomes damaged or illegible, install a new
label in its place.
OPERATION
3
OPERATION
OPERATOR RESPONSIBILITY
The operator’s responsibility is to take care
of the daily maintenance and inspection of
the machine to maintain it in optimal working
condition. It is the operators responsibility
to inform the service technician or supervisor
when the maintenance intervals are required
as stated in the MAINTENANCE section of
this manual.
Read this manual carefully before operating
this machine.
Inspect machine for shipping damage and
make sure the machine is complete according
to your order.
Keep your machine regularly maintained by
following the maintenance information in this
manual. We recommend a regularly scheduled
service contract with your authorized dealer.
Order parts and supplies directly from your
authorized dealer. Use the parts manual
provided when ordering parts.
After use, follow the recommended
daily and hourly procedures shown in the
MAINTENANCE CHART.
FOR SAFETY: Do not operate machine,
unless operation manual is read and
understood.
OPERATION
4
MACHINE COMPONENTS !
"
#
$
%
&
'
(
)
*
+
,
-
.
/
#ONTROL(ANDLE
"ATTERY-ETER
6ARIABLE3PEED+NOB
-ACHINE0OWER+EY3WITCH
"RUSH-OTOR#IRCUIT"REAKER
"ATTERY#HARGING#ONNECTOR
"RUSH0RESSURE,EVER
3OLUTION4ANK3IGHT'UAGE$RAIN(OSE
3CRUB(EAD,IFT0EDAL
3OLUTION&LOW#ONTROL+NOB
3QUEEGEE!SSEMBLY
3OLUTION&ILTER
3QUEEGEE,IFT,EVER
2ECOVERY4ANK$RAIN(OSE
(OUR-ETER
$
%
&
'
(
)
*
!
"
#
/
+
,
-
.
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
2ECOVERY4ANK
"ATTERY#HARGING3UPPORT!RM
"ATTERIES
2ECOVERY4ANK#OVER
3OLUTION4ANK&AST&ILL0ORT
3CRUB"RUSH!CCESS/PENING
3CRUB$ECK
3CRUB$EBRIS3KIRT
%DGE2OLLER
(OSE&ILL/PENING
OPERATION
5
CONTROL PANEL SYMBOLS
4HESESYMBOLSIDENTIFYCONTROLSANDDISPLAYS
ONTHEMACHINE
UNCRATING MACHINE
ATTENTION: Do not roll machine off pallet
without a ramp.
ATTENTION: Install batteries after removing
machine from shipping pallet.
1. Check shipping crate. If damaged, report
to carrier.
2. To uncrate machine, carefully remove
hardware and machine strapping.
INCREASE VEHICLE SPEED
DECREASE VEHICLE SPEED
BATTERY CONDITION METER
NORMAL SCRUB PRESSURE
HEAVY SCRUB PRESSURE
VARIABLE FLOW OR RATE
SOLUTION FLOW
BRUSH MOTOR CIRCIT BREAKER
OPERATION
6
INSTALLING BATTERIES
WARNING: Fire OR Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks
And Flames Away. Charge Batteries With
Cover Open.
FOR SAFETY: When servicing machine, wear
protective glove and eye protection when
managing batteries and battery cables. Avoid
contact with battery acid.
Battery Specifications:
Two deep cycle 12 Volt lead acid batteries.
155 AH battery - Recommended For 20”
Traction Scrubber.
105 AH battery -
130 AH battery -
Maximum battery dimensions:
380 mm (15 in) Length
174 mm (6.85 in) Wide
284 mm (11.18 in) Height
3. Install batteries into the battery compartment.
Secure batteries with supplied battery spacers.
4. Before connecting batteries, make sure terminals
and posts are clean. Use post cleaner and wire
brush if needed.
NOTE: To prevent battery corrosion, apply a light
coating of protective, anti-corrosion spray.
5. Connect battery cables to battery post.
RED TO POSITIVE (+)
BLACK TO NEGATIVE (-)
6. After battery installation, check the battery
condition meter.
1. Park machine on level surface and
remove key.
2. Raise recovery tank to access battery
compartment.
SPACER
FRONT OF SCRUBBER
SPACER
OPERATION
7
1. Park machine on level surface. Remove
the key.
2. Lift squeegee using the lift lever.
3. Mount squeegee assembly to squeegee bracket
as shown. (Ref. Photo)
4. Connect vacuum hose to the squeegee casting.
5. Check squeegee blades for proper deflection.
(Reference: Squeegee blade adjustment)
ATTACHING SQUEEGEE ASSEMBLY
OPERATION
8
BRUSH AND PAD SELECTION
Non-scuff polypropylene scrub brush - A
softer brush intended for use in general purpose
scrubbing for lightly lifting compacted soilage
without scuffing high-gloss coated floors.
Nylon scrub brush - Recommended for
scrubbing coated floors. Cleans without
scuffing surface.
Super abrasive bristle scrub brush - Nylon
fiber impregnated with abrasive grit for
removing heavy stains and soilage. Strong
action works well on build up, grease,
and/or tire marks.
Heavy duty stripping pad - Intended for
stripping floors. Pad aggressively cuts through
old, heavy, floor finishes in preparation for
re-coating.
Stripping pad - Intended for stripping floors.
Quickly and easily cuts through old finish to
prepare the floor for re-coating.
Scrubbing pad - Intended for scrubbing
floors. Removes dirt, spills and scuffs,
leaving a clean surface ready for re-coating.
Buffing pad - Intended for buffing floors.
Quickly cleans and removes scuff marks
while polishing the floor to a high gloss.
Polishing pad - Intended for polishing floors.
Maintains a high gloss. Use for buffing very
soft finishes and lower traffic areas, or use
for polishing soft waxes on wood floors.
Use the correct brush type for your cleaning environment.
Choose from the following brushes and pads.
Table des matières
Autres manuels Onfloor Machine de plancher
Onfloor
Onfloor OF16-2V Mode d’emploi
Onfloor
Onfloor OF20SH Manuel utilisateur
Onfloor
Onfloor OF-2023 Mode d’emploi
Onfloor
Onfloor PRO SERIES 16 Mode d’emploi
Onfloor
Onfloor SWOOP Mode d’emploi
Onfloor
Onfloor OF9S-L Manuel utilisateur
Onfloor
Onfloor OF16SH Mode d’emploi
Onfloor
Onfloor Propel Manuel utilisateur
Onfloor
Onfloor OF-16L Mode d’emploi
Manuels Machine de plancher populaires d'autres marques
Nilfisk-Advance
Nilfisk-Advance Advance SC370 17B Manuel utilisateur
Numatic
Numatic ET 4045 Manuel utilisateur
HAWK ENTERPRISES
HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur
Mytee
Mytee 8070 Mytee-Lite Manuel utilisateur
Kärcher
Kärcher B 140 R Manuel utilisateur
Triple S
Triple S Ace 26T1 Manuel utilisateur
