Oneway Spindle Steady Manuel utilisateur
291 Grith Road Unit 1, Stratford, ON, N5A 6S4, Canada
Phone: 519-271-7611
Fax: 519-271-8892
Email: postbox@oneway.ca
Superior Design, Legendary Quality 1-800-565-7288
www.oneway.ca
Spindle Steady
Instructions
Part No. 3280
Contents Of Package
• Tension Arm Assembly
• Wheels (3) •
• 1¼” Post •
• Base •
• Hardware Package •
• Clamp Block
(lathe specific)
•Note: Clamp Black may be
packaged separately
The ONEWAY Bowl Steady is specically
designed to assist in dampening the
vibration caused when turning medium
to large size bowls. Utilizing the same
“scissor” clamping mechanism as the
Spindle Steady, the Bowl Steady
will accommodate bowls from 10”
all the way up to 24”.
Interested in Turning Bowls?
For more information on the Bowl Steady or
other ONEWAY products, visit our website at:
www.oneway.ca
Manufacturer’s Warranty
Date Purchased: _________________________________
Manufactured parts on this ONEWAY product are backed by a warranty period of
5 years from the date of purchase.
The Wheels and Bearings are not covered under this Warranty.
ONEWAY hereby agrees to repair or replace any defects due to faulty material or
workmanship provided that:
1. The warranty period has not elapsed. Proof of purchase date (sales
receipt etc.) is required prior to any repair taking place.
2. The product has not been altered or modied in any way.
3. The product has not been subjected to misuse, abuse, negligence or
was not used strictly in accordance with these instructions.
4. Transportation costs incurred in returning the product to ONEWAY
Manufacturing is pre-paid by the customer.
This warranty does not cover any costs or damages arising directly or indirectly
from the operation of this product.
No other guarantee, written or verbal is authorized by ONEWAY Manufacturing.
Our policy is one of continuous improvement. We therefore reserve the
right to change the specication and/or design without notice.
Version 4.1 December 2010
Assembly Instructions:
Step 1.
Assemble the Post (Figure 1 No. 1) to the Base Plate (Figure 1 No. 3) using four
¼”- 20tpi x ¾”long Socket Head Cap Screws which are included in the Hardware
Package.
Step 2.
Attach the Tensioning Bar Assembly (Figure 1 No. 2) to the Post (Figure 1 No. 1)
and tighten at the approximate spindle height.
Important Note:
The Tensioning Arm Assembly is pre-assembled for right-hand operation. This
can be changed to accommodate left-hand operation (refer to Figure 1 above
to view the left-handed assembly).
How to use the Spindle Steady:
Postion the Spindle Steady on your machine so that the post is at the back. Ad-
just the height of the tension arm assembly to vertically center the tension arm
assembly with the spindle (exact height adjustment is not critical). Loosen o
all the nuts, open up the tensioning arms and slide the base forward until the
bottom wheel is close to bottom dead center on the spindle you are turning.
Tighten the base to the lathe bed. Once the Spindle Steady is securely fastened
to the lathe, squeeze the tension arms with light pressure to bring the wheels
into contact with the spindle. Be careful not to pull up or push down on the
tensioning arms as this will deect the spindle. Tighten all the nuts starting
with the two that clamp the arms, and nish with the two that clamp the swivel
block.
Removal - reverse the above process to remove the spindle for the steady.
Hardware List
Post
Tension Assembly
Base
¼” - 20 x ¾” socket head cap screws
3/16 short arm hex key
Qty.
1
1
1
4
1
Location
No. 1
No. 2
No. 3
291 Grith Road Unit 1, Stratford, ON, N5A 6S4, Canada
Phone: 519-271-7611
Fax: 519-271-8892
Email: postbox@oneway.ca
Superior Design, Legendary Quality 1-800-565-7288
www.oneway.ca
Figure 1
The Tension Arm
Assembly shown
here is for Left-
handed operation.
31
2
Ce manuel convient aux modèles suivants
1
Autres manuels Oneway Équipement industriel
