One Remote Radio PL3 Manuel utilisateur
OneRemote Radio PL3
Advanced receiver for Bang & Olufsen BeoLab PowerLink speakers, handling
Internet Radio –Spotify
UPnP Music Player –Podcast
Installation Guide
30012013s1uk
www.oneremote.dk
2
ABOUT ONEREMOTE RADIO PL3
Select music or broadcasts to be handled by the OneRemote Radio PL3 via the UNDOK app on one
or more Apple or Android devices. Use either the built- in Internet Radio or stream from other
sources.
Select reproduction from a single OneRemote Radio PL3 or from several units creating a
Multiroom setup.
The OneRemote Radio PL3 is equipped with an internet streaming receiver. When receiving signals
from an internet radio station or from Spotify, streaming is directly to the Radio PL3 not involving
the control device at all. Thus, the control device does not have to be turned on or the app active
between control activities.
App control uses WiFi. Thus, the control can be carried out within the range of the WiFi, and Radio
PL3 needs not to be visible.
The OneRemote Radio PL3 has been re-built with advanced OneRemote circuitry allowing BeoLab
PowerLink speakers to be directly connected and thus creating a complete radio system.
www.oneremote.dk
3
Contents
ABOUT ONEREMOTE RADIO PL3 ........................................................................................................... 2
CONNECTIONS .............................................................................................................................................. 4
PowerLink Speaker Cable.................................................................................................................................................... 4
Internet Connection............................................................................................................................................................ 4
DAILY USE ...................................................................................................................................................... 4
INSTALLATION............................................................................................................................................. 5
www.oneremote.dk
4
CONNECTIONS
POWERLINK SPEAKER CABLE
The OneRemote Radio PL3 connects to BeoLab speakers with a PowerLink cable with 8 pin DIN
connectors. These connectors hold both the right and the left channel signals. The speakers
connect as in any other Bang & Olufsen setup in one of the two following ways:
1. One speaker connects directly to the Radio PL3 with one PowerLink cable, and the other
speaker connects to that one with a second PowerLink cable.
2. Both speakers connect separately to the Radio PL3 with their own PowerLink cable.
If the BeoLab speaker is equipped with a RJ 45 socket instead of a DIN socket, a suitable adaptor
cable must be used.
INTERNET CONNECTION
The OneRemote Radio PL3 may be internet connected either via cable or WiFi.
DAILY USE
With more than one OneRemote Radio PL3 installed a Multiroom system is established, and it is
possible to enjoy different sources in different rooms.
See the User Guide for the daily use of the OneRemote Radio PL3.
See the User Guide for creation and maintenance of program lists.
www.oneremote.dk
5
INSTALLATION
When delivered the OneRemote Radio PL3 is factory reset, in which condition it operates as a
WLAN Access Point, thus creating its own WiFi network.
The first step is to connect a smart phone or tablet to this network enabling connection of the
Radio PL3 to the home network.
The installation is shown with an iPhone, but the procedure for Android is similar.
The iPhone connects to the network
DigitRadio_MR1 available from the
OneRemote Radio PL3.
The Radio PL3 connects to the home
network.
Select cable or WiFi..
Wi-Fi is selected and all networks
within reach are listed.
The home network is chosen and
entering a password may be
rquired.
www.oneremote.dk
6
The Radio PL3 has been configured
and restarts to connect to the home
network.
The system has been configured
and is ready to use.
Press start to use my sound system.
Acquire and install the app UNDOK.
The app opens and shows available
receivers on the home network.
In this particular case one receiver
has already been named.
Select the other one named MR1
and press RENAME.
Enter a reasonable name for the
new receiver.
The receiver has been named and
the menu may be closed. The
installation has been completed.
www.oneremote.dk
7
The OneRemote Radio PL3 may be
used following the directions in the
User Guide.
Table des matières
Autres manuels One Remote Récepteur
One Remote
One Remote 30014002 Manuel utilisateur
One Remote
One Remote Radio PL7 Manuel utilisateur
One Remote
One Remote DVBC-VI Manuel utilisateur
One Remote
One Remote Beo4 Guide d'installation
One Remote
One Remote Radio PL2 Manuel utilisateur
One Remote
One Remote Interface Type 2843 Manuel utilisateur
One Remote
One Remote Radio PL2 Manuel utilisateur
One Remote
One Remote Radio PL4 Manuel utilisateur
