Omron ZX2 Series Comment utiliser

ZX2 Short Manual.doc Page 1 of 12

Short Manual

ZX2 Short Manual.doc Page 2 of 12

1 Safety precautions and correct use

Please refer to the full ZX2 user manual for the detailed explanations of the safety

precautions and the correct use.

2 Wiring

Amplifier

Calculation unit (required

for systems with 2 or more

amplifiers)

Extension cable

(optional, max. 1

piece)

Sensor head

(

10V - 30

)

The HIGH judgement output is switched on if the measurement value is bigger

than the HIGH Threshold value.

The LOW judgement output is switched on if the meansurement value is

smaller than the LOW Threshold value.

The PASS judgement output is switched on if the measurement value is

between the the Low and Hi

h Threshold values.

ZX2 Short Manual.doc Page 3 of 12

3 Default Measurement range

35mm

100mm

10mm

50mm

ZX2-LD50

(

)

ZX2-LD100

(

)

Display:

-10.000

0.000

+10.000 Display:

-35.000

0.000

+35.000

The analog output line can be set to following default ranges (see p.11 and p.12

for additional settings):

ZX2-LD50 ZX2-LD100 -5…5V 1V…5V 4mA…20mA

-10 -35 -5V +1V 4mA

+10 +35 +5V +5V 20mA

ZX2 Short Manual.doc Page 4 of 12

4 Display in RUN mode

Press right or

left button

Orange subdisplay

Displays the selected

bank

Displays the High

Threshold

Displays the Low

Threshold

Displays either the

current or voltage at the

analog output

Displays the current

resolution

Displays the current

measurement value

ZX2 Short Manual.doc Page 5 of 12

5 Functions in RUN mode:

Set the current value to

ZERORESET

ZERO LED turns on

Press the “down arrow” button for 3

seconds. In order to switch off again,

press the up- and down arrow

simultaneously for 3 seconds.

Activate the Key Lock.

Press both “arrow left” and “arrow

right” buttons simultaneously for 3

seconds to activate or deactivate the

Key Lock function.

Activate “Smart Tuning”

Press the SMART button for 1

second to activate the Single Smart

Tuning function, 2 seconds to activate

the Multi Smart Tuning function and 5

seconds to activate the Active Smart

Tuning function.

See page 9

for details!

ZX2 Short Manual.doc Page 6 of 12

6 Setup mode

Pressing and holding the “MENU/SET” button for 3 seconds changes the mode of the

amplifier to the setting mode (pressing again for 3s moves back to RUN mode):

Below you see the navigation through all menus (Details switched on, all other

options switched off) by pressing the left/right arrow button. You change the options

by pressing the up and down arrow buttons and confirm with the Menu/Set button:

MENU LED Indicates

setup mode

Press for 3 seconds

Selection of one of 4 banks.

Setup the response time. The

response time is determined by

the number of averages multiplied

with the cycle time of one

measurement.

Setup the High Threshold for the

digital outputs.

Setup the Low Threshold for the

digital outputs.

Detail*

* Detail: These menus are only displayed if “Detail” is

switched “ON”

Bank*

* Bank: These parameters are set for the current

bank. All other parameters are set globally.

Bank

ZX2 Short Manual.doc Page 7 of 12

Setup the Hysteresis.

Setup the scale of the display and

analog output value. (All settings

(S1/S2) for the scaling are stored

in the bank data. See p. 11.)

Setup the Hold function. See p.

10.

Setup of the analog output either

voltage or current and the output

range.

Setup the behavior of the analog

output in the case that the sensor

is in error state (resp. not able to

obtain a measurement value.

Display: E-dark). See p. 12.

Setup the clamp value for the

analog output (only valid if

RStOUT is set to “Clamp”).

Detail

Bank

ZX2 Short Manual.doc Page 8 of 12

Setup the on-delay of the digital

outputs. See the full user manual

for details.

Setup the off-delay of the digital

outputs. See the full user manual

for details.

Setup the way how the zero-reset

value is stored (permanently or

volatile).

Setup the zero-reset value for the

zero-reset function.

Setup the function of the 2 input

terminals. Either timing and reset

uts or bank select in

uts.

Setup the menu between simple

(“Off”) and detailed (“On”). If

“Detail” is switched to “On” all

menu items are displayed.

Reset the sensor to the factory

defaults. All user defined settings

are deleted.

Detail

ZX2 Short Manual.doc Page 9 of 12

7 Smart Tuning

Smart Tuning sets the optimum parameters for the chosen response time (“Speed”

setting) and the measurement object automatically. The ZX2 has 3 different Smart

Tuning modes:

Single Smart Tuning:

Single Smart Tuning is used if the objects in the final application always have the

same surface characteristic. Place the measurement object in front of the sensor and

press the “Smart” button for 1s:

Multi Smart Tuning:

Multi Smart Tuning is used if there are a couple of different objects in the final

application which are varying in the surface characteristics. Place one after another

of the measurement objects in front of the sensor and press each time the “Smart”

button for 2s:

Active Smart Tuning:

Active Smart Tuning is used if the object(s) is (are) moving in the final application.

The Smart Active tuning is activated by pressing the Smart button for 5s then the

object(s) is (are) passed by in front of the sensor and finally the Smart button is again

pressed for 5s in order to stop the tuning process.

Press for 1 second

Press for 2 seconds

Press for 5 seconds

ZX2 Short Manual.doc Page 10 of 12

8 Hold (=trigger) functions

The hold function is used to hold a certain measurement value while a certain

sampling period. After the sampling period has passed this value is displayed and

applied at the analog output. The possible methods are “Average”, “Peak to Peak”

(=maximum-minimum), “Sample”, “Bottom” and “Peak”. The sampling period is

determined either by an external signal at the Timing Input (purple wire, and menu

setting “Ext-In” set to “TimRSt”) or by a period determined by the measurement value

while it is below or above a certain threshold level (setting “Trig” to “Self-Up” or “Self-

Dn” and the threshold level value under “Self-Level”).

The 5 different hold modes are:

If you have activated one of the HOLD functions and the digital “Timing” input you

can press the “up-arrow” key in “RUN” mode in order to simulate an active signal at

the timing input:

Autres manuels pour ZX2 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Omron Accessoires

Omron

Omron E3M-V - Manuel utilisateur

Omron

Omron ZFX-C10 COMMUNICATION Manuel d'utilisation

Omron

Omron E2C-EDA Series Manuel utilisateur

Omron

Omron E2K-L Manuel utilisateur

Omron

Omron V680-HAM91 Manuel utilisateur

Omron

Omron E3M-V - Manuel utilisateur

Omron

Omron ZX-E - Manuel utilisateur

Omron

Omron TL Manuel utilisateur

Omron

Omron ZG2 Series Manuel utilisateur

Omron

Omron ZX2 Series Manuel utilisateur

Omron

Omron E3FZ-B Manuel utilisateur

Omron

Omron FQ Manuel utilisateur

Omron

Omron E2EZ Manuel utilisateur

Omron

Omron B5WC Manuel utilisateur

Omron

Omron E2EQ Manuel utilisateur

Omron

Omron E3ZM-V61 Manuel utilisateur

Omron

Omron F150-2 Guide de l'utilisateur

Omron

Omron ZS-L - Manuel utilisateur

Omron

Omron E3G-L1 Manuel utilisateur

Omron

Omron ZX-E - Manuel utilisateur

Omron

Omron E3U-GS Manuel utilisateur

Omron

Omron ZX-GT - Manuel utilisateur

Omron

Omron E3S-CL1 Manuel utilisateur

Omron

Omron F150-3 - 2 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur