Omec OMT2 Manuel

Seite 1von 10

–Mounting & Maintenance Instructions –

OMT1 & OMT2 Motors

 
 
 Seite 2von 10 
 
Inhalt Seite 
1General information 3 
2Delivery 3 
3Mounting 3 
4Coupling 3 
4.1 Direct coupling 3 
4.2 Indirect coupling 4 
4.2.1 Flat belt or V-belt 4 
4.2.2 Spur gear transmission 4 
4.3 Shaft couplings 4 
5Electrical connections 4 
5.1 General information 4 
5.2 Circuit details 5 
6Putting into service 6 
7Maintenance 6 
7.1 Dust 6 
7.2 Moisture 6 
7.3 Wear & vibrations 7 
7.4 Greasing 7 
7.5 Replacement of ball or roller bearing 7 
8Bearing types 8 
9Regrasing interval of bearings 8 
10 Disposal 9 
11 Motor spare part list / exploded view 10 

Seite 3von 10

1General information

This manual concerns normal three phase induction motors with an output varying

from small to middle size; they are externally cooled, totally enclosed, supplied in a

cast iron or aluminium frame and provided with ball bearings or roller bearings,

lubricated with grease.

2Delivery

After receipt, remove the package material, if any, and mind the parts that have been

delivered loose.

Check the motor to see whether transport damage has occurred.

You should be able to rotate the shaft easily and smoothly by hand. Compare the

details on the nameplate with those of the power network and with the

requirements of the motor.

3Mounting

The motor must be fixed on a stable, clean and flat foundation with good fitting

foundation bolts, using washers.

Never mount a motor manufactured for a horizontal mounting on a surface with an

angle of inclination of more than 15 degrees without consulting the supplier in

advance. Foot & flange motors always have to be mounted in such a way that the

drain holes, if any, are situated at the bottom, otherwise you risk that moisture will

condensate in the motor and cannot be drained off. To this end you need to remove

the drain plugs.

Under no circumstances the entrance of cooling air, drafted by the cooling fan, may

be obstructed. This will cause overheating of the motor. Special attention is required

where motors will be located in small enclosed rooms.

The ambient cooling temperature must not exceed 40 ºC, unless otherwise agreed

upon at the time of ordering.

4Coupling

4.1 Direct coupling

The motor and driven shafts must be accurately aligned. In case of a flexible coupling,

the manufacturers distance between the parts to be coupled must be adhered to,

also the degree of misalignment must be within the makers tolerance. We do not

recommend using solid couplings.

Seite 4von 10

4.2 Indirect coupling

4.2.1 Flat belt or V-belt

Mount the motor on slide rails in order to adjust belt tension. The belt pulley has to

be fitted hard up the shoulder of the shaft. The pulley center line should be within

the shaft center line.

Use correctly sized belts with a correct profile and in sufficient numbers to drive

without slip and undue tension. Align both pulleys accurately in such a way that the

center of both pulleys are in line.

A belt pulley, which is either too small or too wide, or too high, a tension on the belt

may damage the bearing or cause a shaft break.

In case of doubt, consult the supplier.

4.2.2 Spur gear drives

The motor and the driven machine have to be positioned in such a way that the two

gears align correctly. The motor should then be fixed with dowels.

4.3 Shaft couplings

Remove the corrosion protection from the shaft extension and the coupling

elements. The coupling parts, belt pulleys and gear wheels need to be dynamically

balanced and fit easily on the shaft and to be provided with good fitting keyway.

In the factory the rotor has already been dynamically half-key balanced.

The dimension and the tolerances of the shaft extension and the key are indicated on

the motor dimension sheet. Assembling the coupling elements has to be done with

great care. Careless handling may damage the bearings, shaft or end shields.

Do not file or emery on the shaft to achieve a fit!

When fitting pulleys couplings or bearings, we recommend using heat elements;

therefore the part to be mounted has to be heated till ± 100°C. A large washer and

setscrew can be useful for pushing on pulleys using the tapped hole in the shaft. Only

use proper tools for removing the above mentioned parts e.g. pulley drawers.

5Electrical connections

5.1 General information

On delivery the motor will rotate clockwise looking at the drive when the phases L1,

L2 and L3 are connected respectively to the connection terminals U1,V1 and W1.

Exchanging of any two-phase lines changes the direction of rotation. When a motor is

Seite 5von 10

only suited for one direction of rotation, it is indicated with an arrow on the motor

fan cowl.

Connecting cables must comply with the IEC regulations. Line fuses only protect the

cables in case of short–circuiting and do not constitute a safeguard against the

overheating of the winding caused by overload. Therefore it is recommended that a

motor start- and overload protection is mounted, giving single phase and overload

protection.

5.2 Circuit details

Normally our motors are provided with a terminal box with six connections, to which

six leads from the winding are connected either in a delta connection or in a star

connection by means of connection links. Usually two voltages are indicated on the

rating–plate of these motors, which mean that the motor can be connected to a

circuit having one of these voltages.

If the mains voltage is corresponding with the lowest indicated voltage, the winding

has to be connected in delta connection (see figure 1); if it is corresponding with the

highest indicated voltage, the winding has to be connected in star connection (see

figure 2). A motor with e.g. 230/400V on its rating–plate is suited to be switched on

directly, on a circuit with a voltage of 230 V between phases with the winding

connected in a delta connection, or on a circuit with a voltage of 400 V with the

winding connected in a star connection.

Δ- Connection

low voltage

L1 L2 L3

Abb. 1: Delta connection

Y- Connection

high voltage

L1 L2 L3

Abb. 2: Star connection

If the motor is switched on with a star–delta starter the motor is only suited for a

main voltage on the rating-plate, this is the delta voltage. In this case, the connection

strips on the terminal box have to be removed when the motor is connected. The

star/delta connection will be made successively during the start up.

Seite 6von 10

If only one voltage is indicated on the nameplate together with the delta sign, the

motor can be switched on directly at the indicated voltage or with a star/delta

starter.

Pole change motors (for two or more speeds) are connected according to a diagram

sent together with the motor.

6Putting into service

Before putting a motor into service, one should check especially when the motor has

not been used for a long time that the insulation resistance of the winding is

sufficient. The insulation resistance has to be at least 1.000Ωper Volt, what means at

least 400.000on a supply voltage of 400V.

If the insulation resistance is not high enough, the motor has to be dried out

revarnished or rewound. Check all connections and adjust the thermal protection

units to the correct current. Switch the motor on in a no load state to determine the

direction of rotation. Load the motor gradually and check whether it runs without

vibration. The motor can be used under a variation of the main voltage ± 5% or

frequency variation of max. ± 2% compared to the nominal frequency or nominal

voltage, in compliance with the international regulations for electric machines.

7Maintenance

The totally enclosed and fan cooled three phase squirrel cage induction motors

require very little maintenance. Nevertheless it is recommended to check the motor

regularly in order to prevent a breakdown caused by dust, moisture, vibrations, too

much or too little greasing.

7.1 Dust

The outer parts of the totally enclosed motors, especially the cooling ribs or cooling

channels, have to be kept as clean as possible in order not to obstruct the cooling air

from the fan extracting the heat from the motor frame.

7.2 Moisture

Motors that are stalled for a long time, should be started from time to time to

prevent moisture affecting the windings in the long term. Before putting the motor

into service, one should check especially when the motor has not been used for a

long time that the insulation resistance of the winding is sufficient.

Seite 7von 10

7.3 Wear & vibrations

To prevent abnormal wear & vibration, one should:

a. Take care that the tension of the belt or the chain is not too high;

b. Check whether the mounting of directly coupled machines is correct;

c. Check whether the foundation bolts to fasten the motor and the slide rails are

tightly fixed.

7.4 Greasing

Before the motor leaves the factory, the bearings are filled with a high quality

Lithium base grease. This grase can be mixed with most of the commonly used ball

bearing greases that are lithium-based so that nearly every grease can be used for

regreasing.

Motors from frame size 56 up to frame size 250 are fitted with both sides sealed ball

bearings ( 2RZ ) those filled with grease by the bearing manufacturer “for life time”.

The bearings for those frame sizes without regreasing-divices are completely free of

maintenance. Regular checks can be limited only towards temperature and noise.

Motors from frame sizes 280 up to frame size 400 are equipped with open bearings,

that are filled for 2/3 when the motor leaves the factory. The drive-end shields are

fitted with bearing covers. The lubrication must take place when the machine is

running. The old grease ejects from the grease valve thus maintaining the correct

level and avoiding overfilling which would be harmful.

7.5 Replacement of ball or roller bearing

When a bearing has to be replaced, the old bearing has to be removed from the shaft

with proper tools in order not to damage the shaft. Thereupon the bearing location

on the shaft has to be cleaned and checked thoroughly.

After the new ball bearing resp. the inner ring of aroller bearing has been heated-up

to ca. 80°C till 90°C, it must be mounted on the shaft very soon. If necessary, a short

pipe that fits onto the inner bearing ring can be used to push the bearing to its corret

position.

In no case, it is allowed to blow on the outer ring of the bearing.

Do not mount the end shield until the bearing has cooled down.

Seite 8von 10

8Bearing types

Motortype Poles Drive-end Non-drive-end

OMT2-56 2/4 6201 2RZ C3 6201 2RZ C3

OMT2-63 2/4 6201 2RZ C3 6201 2RZ C3

OMT2-71 2/4/6 6202 2RZ C3 6202 2RZ C3

OMT1/OMT2-80 2/4/6/8 6204 2RZ C3 6204 2RZ C3

OMT1/OMT2-90 2/4/6/8 6205 2RZ C3 6205 2RZ C3

OMT1/OMT2-100 2/4/6/8 6206 2RZ C3 6206 2RZ C3

OMT1/OMT2-112 2/4/6/8 6306 2RZ C3 6306 2RZ C3

OMT1/OMT2-132 2/4/6/8 6308 2RZ C3 6308 2RZ C3

OMT1-160 2/4/6/8 6309 2RZ C3 6309 2RZ C3

OMT1-180 2/4/6/8 6311 2RZ C3 6311 2RZ C3

OMT1-200 2/4/6/8 6312 2RZ C3 6312 2RZ C3

OMT1-225 2/4/6/8 6313 2RZ C3 6313 2RZ C3

OMT1-250 2/4/6/8 6314 2RZ C3 6314 2RZ C3

OMT1-280 2 6314 C3 6314 C3

OMT1-280 4/6/8 6317 C3 6317 C3

OMT1-315 2 6317 C3 6317 C3

OMT1-315 4/6/8 6319 C3 6319 C3

OMT1-355 2 6317 C3 6317 C3

OMT1-355 4/6/8 6322 C3 6322 C3

OMT1-400 2 6320 C3 6320 C3

OMT1-400 4/6/8 6326 C3 6326 C3

9Regrasing interval of bearings

By the term “greasing interval” we mean the number of working hours after which

the bearing lubricant has to be replaced.

Electric motors have such a wide range of application that they must cope with many

adverse conditions as for instance dust, moisture, vibration, temperature, chemicals,

marine atmosphere and of course, the mounting position and loading of the driven

machine.

Generally we can say lubrication life is a product of time, speed and the bearing size.

Due to the impact of all these factors, it is practically impossible to determine any

exact values that are valid under all circumstances. Nevertheless it is necessary to

provide at least some guidelines concerning greasing to the user.

Seite 9von 10

Under normal load and environmental conditions the quality of the grease ensures

proper operation of the motor for about 20000 service hours with 2-pole design and

40000 service hours with multi pole design. If not otherwise agreed upon the grease

need not be refilled during this period. Nevertheless the condition of the grease

filling should be occasionally checked also within the said lubricating intervals.

The stated service hours are only current under operation with rated speed. For

relubrication thoroughly clean the bearings with a suitable solvent and use the same

or substitute grades specified by the motor manufacturer. Bear in mind, however,

that the bearings should be filled only up to about 2/3 of their free space as a

complete filling of the bearings and bearing covers results in an increased bearing

temperature and therefore in increased wear. For bearings with relubricating facility

regrease at the grease fitting with the motor running according to the grease amount

required for the motor in case. The relubrication intervals should be looked up in the

following table:

A chemically aggressive environment, extreme moistness, strong vibrations, high or

low ambient temperatures are not normal circumstances and such conditions must

be taken into account.

Frame size

Motors with 2 poles

Motors with 4 and multi-poles

from 280 up to and incl. 400

2.000 hours

4.000 hours

10 Disposal

The applicable national regulations are to be observed with regard to disposal of the

machines.

It is furthermore to be ensured that oils and greases are collected for disposal in

accordance with the corresponding regulations on waste oils. They must not be

contaminated with solvents, cold cleaners and paint residues. The individual

materials should be segregated for recycling. The most important components are

grey cast iron (housing), steel (shaft, stator and rotor lamination, small parts),

aluminium (rotor), copper (windings) and plastics (insulation materials, such as

polyamide, polypropylene, etc.). electronic components such as circuit boards

(converter, sensors, etc.) are recycled separately.

Seite 10 von 10

11 Motor spare part list / exploded view

Three-phase motor with squirrel-cage rotor

1 V-ring, oil seal DE 22 Mounting screw adoption plate

2 Mounting screw bearing cover DE 23 Lifting eye

3 Outside bearing cover DE 24 Circlip bearing DE

4 Grease-inlet for regrasing device DE 25 Bearing DE

5 Grease-outlet for regreasing device DE 26 Inside bearing cover DE

6 B5-shield DE 27 Key DE

7 B3-shield DE 28 Rotor

8 Mounting screw shield DE 29 Shaft

9 Motor housing 30 Inside bearing cover NDE

10 Gasket terminal box / motor housing 31 Bearing NDE

11 Terminal box 32 Non-drive-end shield

12 Mounting screw terminal box 33 Mounting screw shield NDE

13 Terminal board 34 Outside bearing cover NDE

14 Mounting screw terminal board 35 Mounting screw outside bearing cover DE

15 Connetor pin 36 V-ring, oil seal NDE

16 Nut for connector pin 37 Grease inlet for regreasing device NDE

17 Gasket terminal box / terminal box cover 38 Grease outlet for regreasing device NDE

18 Terminal box cover 39 Fan

19 Mounting screw terminal box cover 40 Circlip fan

20 Adoption plate for cable glands 41 Fan cover

21 Cable gland 42 Mounting screw fan cover

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Omec Moteur

Omec

Omec OMT1 Manuel

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur