OHAUS T21P Manuel utilisateur

T21P Indicator

Instruction Manual

Indicador T21P

Manual de instrucciones

Indicateur T21P

Manuel d’instructions

T21P-Indikator

Bedienungsanleitung

Indicatore T21P

Manuale di istruzioni

Calidad & Servicio, Razones de Peso

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected]m [email protected]

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected]m [email protected]

Calidad & Servicio, Razones de Peso

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogotá, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipesaje@outlook.com

HQ&RORPELD

T21P Indicator EN-1

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the

T21P Indicator. Please read this manual completely before installation and

operation.

1.1 Safety Precautions

For safe and dependable operation of this equipment, please comply

with the following safety precautions:

• Verify that the input voltage range printed on the data label matches the local AC

power to be used.

• Make sure that the power cord does not pose a potential obstacle or tripping

hazard.

• Use only approved accessories and peripherals.

• Operate the equipment only under ambient conditions specified in these

instructions.

• Disconnect the equipment from the power supply before cleaning.

• Do not operate the equipment in hazardous or unstable environments.

• Do not immerse the equipment in water or other liquids.

• Service should only be performed by authorized personnel.

1.2. Overview of Parts and Controls

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

EN-2 T21P Indicator

7 9

Figure 1-1. T21P Indicator.

TABLE 1-1. PARTS AND CONTROLS

Item Description

1AC LED

2Low bat LED

3Zero, Tare, Stable, Accum, Pcs, Unit LEDs

47-segment, 6 digit LED display

5Control Buttons

6Over, Under, Accept LEDs

7On/Off Power Switch

8Power receptacle

9RS232 Connector

10 Load Cell connector

11 Column Bracket

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

T21P Indicator EN-3

1.2. Control Functions

TABLE 1-2. CONTROL FUNCTIONS.

Button

Primary Function

(Short Press) N/A SAMPLE

Enters Sample Setup

Saves APW

ZERO

Sets zero

Secondary Function

(Long Press) SET

Enters Menu Mode

Enters Calibration

Menu during

startup

APW

Displays APW Value

N/A

Menu Function

(Short Press)

Saves Settings and

exits the menu N/A

ENTER

Accepts the

current setting on

the display

Button

Primary Function

(Short Press) TARE

Tares weight of

item on pan

M+

Stores displayed weight

in accumulation

memory

Displays accumulation

data when display is

zero

Sends the current

value to the

RS232 Interface

Secondary Function

(Long Press) N/A N/A

MODE

Change between

weighing and

counting mode

Menu Function

(Short Press)

Decrement value

of settings

Increment value of

settings

Shift to next digit

when setting

parameters

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

EN-4 T21P Indicator

2. INSTALLATION

2.1 Package Contents

• Indicator Unit

• AC Power Adapter

• Load Cell Cable Connector

• Column Bracket

• Instruction Manual

2.2 External Connections

2.2.1 Load Cell Connection

Solder the load cell cable to the supplied load cell cable connector.

Figure 2-1.

iew of pins on

the load cell cable

connector

Pin 1 2 3 4 5 6 7 8 9

Connection SIG- SENS- N/C N/C GND SENS+ EXC+ EXC- SIG+

NOTE: To use a 4 wire load cell cable you must short pin 2 to 8, and pin 6 to 7.

heCAUTION: Never connect a communication cable to the load cell connector of t

indicator. Switch the indicator off when you insert or remove the load cell cable

connector from the indicator.

NOTE:The load cell cable connector cannot pass through the supplied column

bracket. Connect the load cell cable connector to the load cell cable

after

routing the

cable through the column and column bracket. See section 2.2.5 for details.

2.2.2 RS232 Interface Connection

Pin Connection

1N/C

2TXD

3RXD

4N/C

5GND

6-9 N/C

Figure 2-2. View of RS232 Pins on

indicator. (Item 9 in Figure 1-1)

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

T21P Indicator EN-5

2.2.3 AC Power

Connect the AC Adaptor to the power receptacle, and then plug the AC Adapter into a

properly grounded electrical outlet. The AC LED will light (Figure 1-1, item 1).

Power

Receptacle

Figure 2-3. Power Connection

2.2.4 Battery Power

The indicator can be operated on the internal rechargeable battery when AC power is

not available. The indicator will automatically switch to battery operation if there is a

power failure or the power cord is removed.

NOTE: Before using the scale for the first time, the battery should be fully

charged for up to 12 hours. The indicator can be operated during the

charging process. The battery is protected against over charging and the

indicator can remain connected to the AC power line.

The indicator can operate up to 30 hours on a fully charged battery.

The indicator automatically enters standby mode after 1 minute of no activity. The

display will only show the decimal point [ . ]. Press on the pan or any key to

resume.

During battery operation, the Low Bat LED will illuminate when the battery is low and

requires recharging. Approximately 30 minutes of operation will remain. The

indicator will automatically turn off when the battery is fully discharged.

CAUTION: The battery is to be replaced only by an authorized Ohaus

service dealer. Risk of explosion can occur if the battery is replaced with

the wrong type or is connected improperly.

Dispose of the lead acid battery according to local laws and regulations.

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

EN-6 T21P Indicator

2.2.5 Mounting Column Bracket

The Indicator can be mounted to a scale column of 38mm outside diameter with the

supplied column bracket.

1. Route the cable through the column and the column bracket.

2. Slide the column bracket down onto the column and tighten the nut.

3. Solder the load cell cable to supplied load cell cable connector (see section

2.2.1).

4. Slide the indicator onto the bracket as shown below.

5. Plug the load cell cable into the indicator load cell connector Figure 1-1,

Item 10.

6. Remove the upper knob to change the viewing angle, re-install the knob to

fix the position.

2.3 Opening the Housing

CAUTION: ELECTRICAL SHOCK HAZARD. REMOVE ALL POWER

CONNECTIONS TO THE INDICATOR BEFORE SERVICING OR MAKING

INTERNAL CONNECTIONS. THE HOUSING SHOULD ONLY BE OPENED

BY AUTHORIZED AND QUALIFIED PERSONNEL, SUCH AS AN ELECTRICAL

TECHNICIAN.

2.4 Initial Setup and Calibration

Once properly assembled and powered up, set up the scale parameters (Section 4)

and calibrate (Section 5).

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

T21P Indicator EN-7

3. OPERATION

3.1 Turning Scale On/Off

To turn the scale on, toggle the switch on the right side of the indicator to the on

position. The scale performs a display test, momentarily displays software version,

and then enters the active weighing mode. To turn the scale off, toggle the switch to

the off position.

3.2 Zero Operation

Zero is set under the following conditions:

• Automatically at Power On (initial zero). Refer to section 4.3 [F1-2] for settings.

• Manually by pressing the ZERO button.

Press the ZERO button to zero the weight display. The scale must be stable and

within the zero range. Refer to section 4.3 [F1-0].

3.3 Manual Tare

Place a container on the weighing pan, then press TARE. The display will show a net

value of “0”. To clear the Tare value, press TARE with the pan empty.

Tare capacity is user selectable (Section 4.2).

3.4 Weighing Mode

Use this mode to measure the weight of a sample in the selected unit of measure.

Press ZERO to set the display to zero. Put an empty container on the pan, and then

press TARE to tare the container weight. Add material to the container. The display

shows the weight of the material in the selected unit of measure. See Section 4.3

[F1-3]to change the unit of measure.

3.5 Counting Mode

Use this mode to count parts of uniform weight.

When in weighing mode press SAMPLE to set the sample size.

[p00010] or the last used value will be displayed.

Press ¨, ª, ©to edit the sample size.

Place the displayed quantity of samples on the scale or tared container.

Press SAMPLE to calculate the Average Piece Weight (APW) and enter counting

mode or press ENTER to exit to weighing mode without saving changes.

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

EN-8 T21P Indicator

Long press MODE to toggle between counting and weighing modes. The Pcs LED

will illuminate to indicate counting mode.

Place parts on the scale or a tared container and read the count.

Press ZERO or SAMPLE to exit to weighing mode.

To display the APW value, exit to weighing mode and then press and hold APW. The

display will show [APwW] and [xxxxxx], where x= APW value, and will return to

weighing mode.

3.6 Weight Accumulate Mode

Use this mode to store the weight and HI, LO, SUM statistics from a series of

samples.

Place the sample on the pan or tared container.

Press M+ to store the weight of the sample. Storage is confirmed by the display

[n x], where x is the total number of samples. The Accum LED will illuminate to

let the user know there are readings in memory. Remove the sample, wait for stable

zero reading, then place the next sample on the pan. Press M+ to store the weight of

the next sample. Repeat this process until all samples have been weighed.

Review the accumulation data by pressing M+ when the display is at zero.

The display shows the total number of samples [n x].

Press M+ to view the maximum sample weight [Hxxxxx].

Press M+ to view the minimum sample weight [Lxxxxx].

Press M+ to view the sum of the weights [xxxxxx].

Press M+ to return to weighing.

To clear the accumulated data press ZERO when the number of samples [n x]

is displayed.

NOTE: A total of 999 accumulation records [n 999] can be stored. The sum of

the weights cannot exceed [999999]. The indicator displays [n_Over] or

[a_Over] if these values are exceeded. Clear the accumulated data to continue

Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: (571) 263 72 24 Bogota, D.C. - Colombia.

www.tecnipesaje.com [email protected] tecnipes[email protected]

Table des matières

Langues :

Autres manuels OHAUS Écran tactile

OHAUS

OHAUS CKW-55 Manuel utilisateur

OHAUS

OHAUS T32ME Manuel utilisateur

OHAUS

OHAUS 3000 Series T32XW Manuel utilisateur

OHAUS

OHAUS T51P Manuel utilisateur

OHAUS

OHAUS Ranger 3000 Series Manuel utilisateur

OHAUS

OHAUS 5000 Series Manuel utilisateur

OHAUS

OHAUS T71P Manuel utilisateur

OHAUS

OHAUS Ranger 3000 Series Manuel utilisateur

OHAUS

OHAUS CD-31 Manuel utilisateur

OHAUS

OHAUS T51P Manuel utilisateur

OHAUS

OHAUS 3000 Series T31P Manuel utilisateur

OHAUS

OHAUS T71P Manuel utilisateur

OHAUS

OHAUS Ranger 3000 Series Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS DEFENDER 7000 XtremeW Series Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur