OHAUS Explorer E1F110 Manuel utilisateur

Ohaus Explorer

Manufacturer: Ohaus

Product Range: Explorer

Model Tested: E1F110

Capacity - 6100g

Readability - 0.1g

Note:

The Explorer normally comes with an RS232 serial interface fitted as standard, please check with your balance supplier

that this is the case.

Setting up the balance:

• Getting into RS232 Mode

Turn the unit on.

Press the “Setup” button.

Press the “right” button until “RS232” is displayed then press the “Enter” button.

• Setting the Baud rate to 1200.

“BAUD” should now be displayed, press the “Enter” button.

Press the up or down buttons until “1200” is displayed then press the “Enter” button.

• Setting the Parity to none.

“PARITY” should now be displayed, press the “Enter” button.

Press the up or down buttons until “nonE” is displayed then press the “Enter” button.

• Setting the Data to 7 bits.

“DATA” should now be displayed, press the “Enter” button.

Press the up or down buttons until “7” is displayed then press the “Enter” button.

• Setting the Stop bits to 2.

“STOP” should now be displayed, press the “Enter” button.

Press the up or down buttons until “2” is displayed then press the “Enter” button.

• Setting Lock to Off.

“LOCK” should now be displayed, press the “Enter” button.

Press the up or down buttons until “OFF” is displayed then press the “Enter” button.

• Returning to normal operation.

“EXIT” should now be displayed, press the “Enter” button.

Serial Balance Adapter Data Sheet OH-2

© DCP Microdevelopments Ltd www.dcpmicro.com [email protected] 12/12/00

Setting up the balance (continued):

• Getting into Print setup mode.

Press the “Setup” button.

Press the “right” button until “PRINT” is displayed then press the “Enter” button.

• Setting the balance to autoprint.

“AUTOPRT” should now be displayed, press the “Enter” button.

Press the up or down buttons until “CONT” is displayed then press the “Enter” button.

• Returning to normal operation.

Press the left or right buttons until “Exit” is displayed, press the “Enter” button.

The balance is now set up to work with the LogIT Serial Balance Adapter - See Connecting the Balance for details of the

lead required to connect the balance to the LogIT Adapter.

Connecting the balance:

A cable must be made to connect the balance serial port to the LogIT Serial Adapter using the wiring information below.

Explorer RS232 port, 9 way D Socket Balance Adapter, 9 Way D Socket

pin 2 pin 2

pin 5

pin 6

pin 7 pin 5

Note: These connection instructions are designed for use with the 9 pin boxed version of the LogIT Serial Balance

Adapter. If using the original 25 pin lead type connection you need to use adapter pin 3 instead of pin 2 (data out) and

adapter pin 7 instead of pin 5 (ground).

Serial Balance Adapter Data Sheet OH-2

© DCP Microdevelopments Ltd www.dcpmicro.com [email protected] 12/12/00

Connect balance pin 5 to pin 6 to bypass handshaking

Table des matières

Autres manuels OHAUS Échelle

OHAUS

OHAUS Adventurer AX224 Manuel utilisateur

OHAUS

OHAUS Adventurer Pro AV811 Series Manuel utilisateur

OHAUS

OHAUS 5000 Manuel utilisateur

OHAUS

OHAUS Adventurer AX2201/E Manuel utilisateur

OHAUS

OHAUS HH 320 Manuel utilisateur

OHAUS

OHAUS Valor 1000W Manuel utilisateur

OHAUS

OHAUS Ranger Manuel utilisateur

OHAUS

OHAUS 7000 Series Manuel utilisateur

OHAUS

OHAUS SD Manuel utilisateur

OHAUS

OHAUS Navigator NV212 Manuel utilisateur

OHAUS

OHAUS TROOPER COUNT Manuel utilisateur

OHAUS

OHAUS Scout SPX Series Guide d'installation

OHAUS

OHAUS SPJ Carat Manuel utilisateur

OHAUS

OHAUS Compass CX Series Manuel utilisateur

OHAUS

OHAUS RC31P1502-M Manuel utilisateur

OHAUS

OHAUS VE Series Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS Scout SPX Series Manuel utilisateur

OHAUS

OHAUS Guardian 2000 Manuel utilisateur

OHAUS

OHAUS SJX323 Manuel utilisateur

OHAUS

OHAUS TA152 Manuel utilisateur

OHAUS

OHAUS 2400-11 Manuel utilisateur

OHAUS

OHAUS Scout SJX Manuel utilisateur

OHAUS

OHAUS Voyager V10640 Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur