OHAUS Defender 3000 Series Manuel utilisateur
DEFENDER 3000 Series Floor Scale
Instruction
Manual
Báscula para piso serie DEFENDER 3000
Manual
de instrucciones
Balance au sol Série DEFENDER 3000
Manuel d’instructions
Bodenwaage der DEFENDER 3000-Serie
Bedienungsanleitung
Bilancia da pavimento serie DEFENDER 3000
Manuale
di istruzioni
Manual_DF_V1
DEFENDER 3000 Series Floor ScaleEN-2
DEFENDER 3000 Series Floor Scale EN-3
INTRODUCTION
This manual contains installation, operation and maintenance instructions for the DEFENDER 3000 Series Floor
Scale.
SAFETY PRECAUTIONS
Please follow these safety precautions:
•Never operate in hazardous areas.
•The foundation at the installation site must be capable of safely supporting the weight of the
floor scale plus the weight of the maximum load.
•Ensure that vibrations due to machines near the installation site are kept to a minimum. This
applies also when the floor scale is integrated into conveying systems.
INSTALLATION
CAUTION: THE FLOOR SCALE IS VERY HEAVY.
ALWAYS USE AN APPROPRIATE HOIST TO LIFT IT FROM THE PACKAGING
OR TO MOVE IT INTO THE REQUIRED POSITION.
Unpacking
1. Remove the outer packaging
materials from the top and sides
of the floor scale.
2. Install the two included eye bolts
into holes in top of platform.
(See Figure 1.)
3. Lift the floor scale from the
packaging material, see caution
notice.
EYE BOLT
LOAD CELL FEET
SHIPPING FEET (IF INSTALLED)
Figure 1. Hoisting Method.
DEFENDER 3000 Series Floor ScaleEN-4
Positioning
Ensure the surface is flat in the area where the scale will be positioned, especially in the region of the load cell feet.
Small differences in height can be compensated by adjusting the load cell feet.
1. If an Indicator is included with the floor scale, ensure that it is kept with the floor scale during positioning as
there may be an attached connecting cable.
2. With the floor scale positioned over the final work area, remove the 4 shipping feet (if installed).
3. Install the 4 load cell feet (if not already installed).
4. Lower the scale on to the final work area.
5. Check that the floor scale is level; check that the 4 feet are in contact with the floor; make adjustments by
rotating the nuts on the load cell feet. Use an external level.
6. Ensure that the floor scale’s output cable does not become trapped or crushed during lifting or positioning.
Connecting an Indicator
Certain Floor Scale systems will have an Indicator already attached to the cable end. If the Indicator is not
attached or if the Indicator is purchased separately follow the steps listed below to make the proper connections.
1. Route the Floor Scale cable to the position where
the Indicator will be mounted.
2. Consult the installation instructions of the Indicator
to properly attach the cable connections inside the
Indicator,
3. The Signal names of the Floor Scale wires are
shown in Table 1, Floor Scale Wiring Color Code.
Caution: Ensure that the cable is protected against
possible damage when routed to the
Indicator.
TABLE 1. FLOOR SCALE WIRING COLOR CODE
Indicator Signal Name Floor Scale Wire Color
EXC+ (IN+) Green
SEN+ Yellow
SIG+ (OUT+) White
SIG– (OUT–) Red
SEN– Blue
EXC– (IN–) Black
Shield (GND) Yellow/Green
DEFENDER 3000 Series Floor Scale EN-5
OPERATION
For setup, calibration and proper operation, refer to the instruction manual supplied with the indicator. Refer to the
specifications section of the floor scale for capacity, and readability information.
For continued best operating performance:
•Avoid falling loads, shocks and hard lateral impacts
•When weighing, all items should be centrally located on the floor scale and not
over hanging the sides or the ramps.
•Verify the calibration of the floor scale system at regular intervals.
Operating Limits
Although the floor scales have extremely rugged construction, certain load limits must not be exceeded. Depending
on the type of loading, the maximum safe static load, i.e. the maximum admissible loading, is shown in Table 2.
TABLE 2. MAX ADMISSIBLE LOADING
Model Maximum Central Load 1
(80% Surface Area)
Maximum side Load 2
(30% Surface Area)
One Side corner load 3
(10% Surface Area)
DF1500BS 2500 kg 1500 kg 1000 kg
DF1500BR 2500 kg 1500 kg 1000 kg
DF1500BL 2500 kg 1500 kg 1000 kg
DF3000BL 3800 kg 1800 kg 1200 kg
DF1500BX 2500 kg 1500 kg 1000 kg
DF3000BX 3800 kg 1800 kg 1200 kg
DF3000BV 3800 kg 1800 kg 1200 kg
DF1500BRL 2500 kg 1500 kg 1000 kg
DF1500BLX 2500 kg 1500 kg 1000 kg
DF3000BLX 3800 kg 1800 kg 1200 kg
DEFENDER 3000 Series Floor ScaleEN-6
MAINTENANCE
Daily Checks
•Check that the rocker feet are properly seated in the holes of each load cell.
•Check that the 4 feet are in contact with the floor.
•Check that the scale is free from debris, especially under the edges of the scale.
•Check that there is no damage to the connecting cable.
Cleaning
Risk of Electrical Shock
Disconnect the power source before cleaning the scale with any liquids.
Maintenance of the floor scale is limited to regular cleaning.
– Wipe surfaces with a damp cloth.
– Use only common household cleaning agents.
– Never use water spray or high pressure cleaners.
When using optional Ramps or Foot Plates:
– Keep the air gap at the edge of the Floor Scale free of debris.
DEFENDER 3000 Series Floor Scale EN-7
TECHNICAL DATA
Specifications
TABLE 3. FLOOR SCALE SPECIFICATIONS
Floor Scale Models DF1500BS DF1500BR DF1500BRL DF1500BL
DF3000BL
DF1500BLX
DF3000BLX
DF1500BX
DF3000BX DF3000BV
Dimensions (mm) 800 x 800 x 110 1,000 x 1,000 x 110 1,000 x 1,200 x 110 1,200 x 1,200 x 110 1,200 x 1,500 x 110 1,500 x 1,500 x 110 2,000 x 2,000 x 110
Capacity (kg) 1500 1500 1500 1500 / 3000 1500 / 3000 1500 / 3000 3000
Operating tempera-
ture/ Humidity –10°to 40°/ 0% to 95% Relative Humidity, Non-condensing
Emin (kg) 0.5 0.5 0.5 0.5 / 1 0.5 / 1 0.5 / 1 1
Material Painted carbon steel, black painted, treaded surface, fixed top plate 5 mm thick
Platform net wt (kg) 72 90 105 122 209 249 375
Feet 4 x swivel design, screw-in, carbon steel with rubber bottom cap, adjustable height
Load Cell Model /
Material 4 x OIML C3, IP67 alloy steel, shear beam
Load Cell Capacity
Emax (kg) 1,000 1,000 / 1,500 1,500
Load Cell Safe
Overload Limit 150% of Emax
Load Cell Output
Impedance 350 Ω± 1 Ω
Load Cell Excitation
Voltage 5V ~ 15V, DC/AC
Junction Box Top access, IP65, Stainless steel, with 5m long cable
DEFENDER 3000 Series Floor ScaleEN-8
DRAWINGS
Figure 2. Floor Scale Dimensions, (Shown with optional Foot Plates)
TABLE 4. FLOOR SCALE DIMENSIONS
DIMENSIONS(mm)
FLOOR SCALE PLATFORM FOOT CENTERS
MODELS
A B H W L
DF1500BS 800 800 110 700 700
DF1500BR 1000 1000 110 900 900
DF1500BL
DF3000BL 1200 1200 110 1100 1100
DF1500BX
DF3000BX 1500 1500 110 1400 1400
DF3000BV 2000 2000 110 1900 1900
DF1500BRL 1200 1000 110 900 1100
DF1500BLX
DF3000BLX 1500 1200 110 1100 1400
DEFENDER 3000 Series Floor Scale EN-9
ACCESSORIES
TABLE 5. LIST OF ACCESSORIES
ITEM PART NUMBER
Foot Plate Kit, Painted steel, DF-B 72225239
Ramp Kit, Painted steel, 0.8m, DF-B 80252722
Ramp Kit, Painted steel, 1.0m, DF-B 80252723
Ramp Kit, Painted steel, 1.2m, DF-B 80252724
Ramp Kit, Painted steel, 1.5m, DF-B 80252725
Ramp Kit, Painted steel, 2m, DF-B 80252726
Pit Frame Kit, Painted steel, 0.8m, DF-B 83033708
Pit Frame Kit, Painted steel, 1.0m, DF-B 83033709
Pit Frame Kit, Painted steel, 1.2m, DF-B 83033710
Pit Frame Kit, Painted steel, 1.5m, DF-B 83033711
Pit Frame Kit, Painted steel, 2.0m, DF-B 83033712
Pit Frame Kit, Painted steel, 1.0m x 1.2m, DF-B 83033713
Pit Frame Kit, Painted steel, 1.2m x 1.5m, DF-B 83033714
DEFENDER 3000 Series Floor ScaleEN-10
DEFENDER 3000 SERIES FLOOR SCALE,
Installation of Optional Foot Plates and Ramps
Plates are required for certifiable installations. Installation of each Ramp also requires the installation of one set of
Foot Plates. Foot Plates are available separately and are included with the Ramp accessory kit. Refer to Figure 3
for mounting of the Foot Plates and Ramps. Installation of Floor Plates and Ramps must be done before final
placement of the Floor Scale.
Figure 3. Optional Foot Plate and Ramp Installation
Notes: 1. Expanding bolts require 12.5mm diameter holes drilled 60mm deep into the floor surface.
2. Foot Plate center to center dimensions W and L are shown in Table 6.
3. The Floor Scale must be positioned so the load cell feet rest within the large holes of the Foot Plates.
4. Ensure that a free air gap exists between the sides of the Floor Scale and the edges of the Ramps.
TABLE 6. DIMENSIONS FOR FLOOR PLATE AND RAMP INSTALLATION
DIMENSIONS (mm)
RAMP FOOT PLATE CENTERS
MODELS
A B W L
DF1500BS 800 800 700 700
DF1500BR 1000 1000 900 900
DF1500BL
DF3000BL 1200 1200 1100 1100
DF1500BX
DF3000BX 1500 1500 1400 1400
DF3000BV 2000 2000 1900 1900
DF1500BRL 1200 1000 900 1100
DF1500BLX
DF3000BLX 1500 1200 1100 1400
Autres manuels pour Defender 3000 Series
9
Ce manuel convient aux modèles suivants
10
Table des matières
Langues :
Autres manuels OHAUS Échelle
OHAUS
OHAUS Courier 7000 Manuel utilisateur
OHAUS
OHAUS Guardian 3000 Manuel utilisateur
OHAUS
OHAUS Ranger Manuel utilisateur
OHAUS
OHAUS Defender D30BR Manuel utilisateur
OHAUS
OHAUS Adventurer series Manuel utilisateur
OHAUS
OHAUS ES series Manuel utilisateur
OHAUS
OHAUS Scout SPX Series Manuel utilisateur
OHAUS
OHAUS Valor 2000 V22PW Guide d'installation
OHAUS
OHAUS Adventurer AX124/E Manuel utilisateur
OHAUS
OHAUS CL Series Manuel utilisateur
OHAUS
OHAUS Scout pro Manuel utilisateur
OHAUS
OHAUS Navigator Rechargeable Battery Manuel utilisateur
OHAUS
OHAUS Catapult 1000 Manuel utilisateur
OHAUS
OHAUS EX224 Manuel utilisateur
OHAUS
OHAUS CL Series Manuel utilisateur
OHAUS
OHAUS HP-120 Manuel utilisateur
OHAUS
OHAUS Defender 3000 Series Manuel utilisateur
OHAUS
OHAUS EXPLORER Manuel utilisateur
OHAUS
OHAUS Ranger Manuel utilisateur
OHAUS
OHAUS Ranger 3000 Series Manuel utilisateur
