OHAUS BW Series Manuel utilisateur
Quick Start Guide BW Scales
Ohaus Corporation www.ohaus.com iBW Compact Bench Scales Quick Start Guide
PREPARATION FOR USE
Remove shipping protection screws on the
platform support, and plastic column inserts
under it. Re-install them if shipping the scale.
To minimize condensation inside the scale,
slightly loosen rear leveling feet; then level the
scale for normal operation. (Tighten all feet
when cleaning scale.)
To use AC power, remove rubber seal on
bottom to insert adapter plug in jack.
Battery charges when AC adapter is
connected. Scale switches to battery power if
AC power stops. Normal battery operating
time is 50 hours on a 15-hour charge.
Note: To prevent water ingress during use,
insert rubber Seal into the input jack recess.
SELECTING THE LOCATION
Place on a firm, steady surface.
Avoid locations with excessive air current,
vibrations, heat sources, or rapid temperature
changes.
Level the scale: Adjust leveling feet so bubble
is centered.
SAFETY PRECAUTIONS
For safe and dependable operation, observe the following safety precautions:
•Verify that indicated input voltage on Adapter and plug matches local power supply.
•Make sure that the power cord does not pose an obstacle or tripping hazard.
•Disconnect the product from the power supply when cleaning.
•Do not operate this product in hazardous or unstable environments.
•Do not drop loads on the pan.
•Use only approved accessories and peripherals, as available.
•Operate the product only under ambient conditions specified in the Instruction Manual.
•Service should be performed by authorized personnel only.
Plastic
column
inserts
Leveling
Feet
Shipping
protection
screws
BW Scales Quick Start Guide
BW Compact Bench Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com
CONTROLS
• Turns the scale on
• Long-press turns the scale off
• In SETUP Mode, “Yes” accepts/confirms the displayed setting
• In CHECK Mode, accepts/confirms the displayed value
90
TARE
No
• Inputs the weight of the object on the weighing pan as a Tare value
• In SETUP Mode, “No” toggles through the available settings
• In CHECK Mode, increments the value of the selected digit
• Zeros the display
• With the scale off, long-press together with ON/OFF enters User Setup Mode
• In SETUP Mode, “Exit” ends setup and exits to “Save”
• In CHECK Mode, ends Over/Under setup and exits to weighing mode
• Initiates CHECK Over/Under setup
• In SETUP Mode, “Back” reverts to the previous parameter
• In CHECK Mode, shifts to the next digit
Center of zero
indicator
Battery charged
indicator
Active weighing unit indicator:
g– grams
kg
–
Kilograms
Indicates displayed
weight is Under or Over
preset value
Low Battery
indicator
Net (Gross minus
Tare) indicator
Quick Start Guide BW Scales
Ohaus Corporation www.ohaus.com iii BW Compact Bench Scales Quick Start Guide
OPERATION
Turning Scale On/Off
Press ON. After a display test, scale enters active weighing mode.
Allow 15-30 minutes for warmup.
To turn the scale off, long-press Off.
Zero Operation
Press ZERO to zero the stable weight display.
(Weight must be within ±2% of scale capacity). Center of Zero indicator lights up.
Manual Tare
Place a container on the weighing pan and press TARE.
Display shows net value of “0”.
To clear Tare value, press TARE with pan empty.
90
TARE
No
Checkweigh Target Setting
Compares the weight of an item against a pre-set Over-Under range.
To activate Checkweighing Mode, see Menu – next page.
• Press CHECK to enter Over-Under parameters.
• Value of “OVER” target appears first, with active digit flashing. (OVER LED is lit.)
Press No to increment the active digit or CHECK to shift to the next digit.
• Press Yes to accept the displayed value and proceed to “UNDER” target.
Now the UNDER LED is lit.
90
TARE
No
• Press No to increment the active digit or CHECK to shift to the next digit.
• Press Exit to accept displayed value and exit into checkweighing mode.
Notes:
• OVER or UNDER LEDs light if weight on pan is over or under the pre-set limits.
• OVER and UNDER LEDs light simultaneously if weight is within pre-set limits.
• The LED indication is complemented by a beep.
• Over-Under values are retained when the unit is turned off.
• Over-Under values are not retained when the weighing unit or resolution setup are changed.
BW Scales Quick Start Guide
BW Compact Bench Scales Quick Start Guide iv Ohaus Corporation www.ohaus.com
Accessing the User Setup Mode
With the scale off, press ON/OFF and ZERO simultaneously.
When the scale turns on, release ON/OFF but keep pressing ZERO until SETUP appears
To navigate in the User Setup Mode, press:
to accept the displayed setting
to end setup and proceed to “Save”
to toggle through available settings
to revert to the previous parameter
User Setup Parameters
Parameters
Description Settings
S1
Scale automatically turns off
after 15 minutes of inactivity.
ON - enables this function.
OFF -disables this function.
S2
Scale enters sleep mode after
two minutes of inactivity.
ON - enables this function.
OFF -disables this function.
S3
CHECK activation and
Alert Range
0 - Check mode is off.
Scale beeps when displayed weight is:
1–…within the preset Over and Under values
2–…outside the preset Over and Under range
3–…within the preset Over and Under values
(Over-Under LED’s do not light within preset range)
4–…outside the pre-set Over and Under range
(Over-Under LEDs do not light within preset range)
5– Alarm is off
(Over-Under LED’s do not light within preset range)
6– Alarm is off
S4
Averaging Level 0, 1, 2, 3 (most filtering, longer stabilization time)
4, 5, 6, 7 (corresponds to 0, 1, 2, 3 but with slower
display update)
S5
Weighing Unit Lb, oz, g
S6
LED Brightness Level 0,1,2,3 (dimmest).
DSP
Display Type OFF – displays weight continuously.
ON – displays first stable weight.
S8
Resolution OFF – 3000 scale divisions
ON – 6000/7500 scale divisions
Save
Save or Abort Save – saves changes and reverts to weighing mode.
Abort – reverts to weighing mode without saving
changes.
Note: Bold settings are defaults.
*80253134*
P/N 80253134
Autres manuels pour BW Series
1
Table des matières
Autres manuels OHAUS Échelle
OHAUS
OHAUS Scout SPX Manuel utilisateur
OHAUS
OHAUS Explorer EX1241 Manuel utilisateur
OHAUS
OHAUS RC41M15-M Manuel utilisateur
OHAUS
OHAUS Ranger Manuel utilisateur
OHAUS
OHAUS VE Series Manuel utilisateur
OHAUS
OHAUS Scout Pro Balance Manuel utilisateur
OHAUS
OHAUS defender 7000 Manuel utilisateur
OHAUS
OHAUS Valor V31X Manuel utilisateur
OHAUS
OHAUS TAJ Carat TAJ203 Manuel utilisateur
OHAUS
OHAUS Ranger Count 3000 Series Manuel utilisateur
OHAUS
OHAUS Compass CX221P Manuel utilisateur
OHAUS
OHAUS Skipper 5000 Manuel utilisateur
OHAUS
OHAUS adventurer+ Manuel utilisateur
OHAUS
OHAUS Valor 1000 Manuel utilisateur
OHAUS
OHAUS CS 2000 Manuel utilisateur
OHAUS
OHAUS Valor 1000W Manuel utilisateur
OHAUS
OHAUS RI Series Manuel utilisateur
OHAUS
OHAUS Ranger 3000 Series Manuel utilisateur
OHAUS
OHAUS Valor 2000W Series Manuel utilisateur
OHAUS
OHAUS Scout SKX Manuel d'utilisation
