Office Zone MightyLam 2700 Manuel utilisateur
Safety Messages and Electrical Safeguards ..............................1-2
Introduction .................................................................................2-3
Laminator Features .................................................................3
Specifications ...................................................................................3
Intial Set-up ..................................................................................4-5
Unpacking ...............................................................................4
Components .........................................................................4-5
Operation ......................................................................................5-8
Loading Laminating Film .......................................................5
Threading Laminating Film ..................................................6-7
Adjusting Mandrel/Film Tension.............................................7
Heat Shoe Temperature ...........................................................8
Adjusting Slitter Blades ...............................................................8-9
Laminating ..................................................................................9-11
Coating Mount Board.............................................................10
Mounting & Laminating.........................................................11
Troubleshooting ........................................................................12-13
Maintenance ..............................................................................13-14
Cleaning Heat Shoes & Rollers .......................................13-14
Removing Wrap-Arounds......................................................14
Warranty & Return Policy ...........................................................14
Parts List ....................................................................................15-17
Parts Illustrations ......................................................................18-21
Exploded View .......................................................................18
Side Panels ........................................................................19-20
Wiring Diagram.......................................................................21
TABLE OF CONTENTS
1-800-543-5454 www.officezone.com
OfficeZone
IMPORTANT SAFETY MESSAGES AND
ELECTRICAL SAFEGUARDS
For your protection, do not connect the laminator to electrical power or attempt to operate it
until you read these instructions completely. Keep these instructions in a convenient loca-
tion for future reference. This instruction manual and labels affixed to the laminator are
important safety messages. Read these messages carefully.
For your safety...
Save these Operating Instructions for later use.
Keep hands, long hair, clothing, and other loose articles such as jewelry and ties,
away from laminator’s moving parts.
Do not touch the heat shoes while the laminator power is turned on. Allow shoes
to cool completely before touching.
Do not use the laminator for other than its intended purpose.
Place laminator on a sturdy cart, stand, or table. A laminator placed on an un-
stable surface may fall, causing serious bodily injury. Move laminator with cau-
tion. Quick stops, excessive force, or uneven floor surfaces may cause the
laminator and cart to overturn.
Never insert objects or spill liquids in or on the laminator. They may contact
dangerous voltage points or short out components that could result in fire or
electrical shock.
The laminator should only be operated from the type of power source indicated
in these Operating Instructions and on the data plate located on the rear panel of
the laminator.
The three-pronged grounding plug is a safety feature and will only fit into a
grounding-type power outlet. If you are unable to insert the plug into an outlet
contact a qualified electrician to have a suitable outlet installed.
Do not leave the laminator power on overnight. Unplug the laminator at the end
of the day.
1
1-800-543-5454 www.officezone.com
OfficeZone
Unplug the laminator before moving it or when it is not in use for an extended
period of time as a precaution against the possibility of an internal malfunction
that could create a fire hazard.
Do not operate the laminator with a damaged power supply cord or plug, or after
it malfunctions or has been damaged in any manner.
Keep the power cord away from hot or wet surfaces.
Do not overload electrical outlets beyond their capacity as this can result in fire
or electrical shock. This unit is rated at 15 amps and should be the only item
plugged into a 15 amp branch circuit. When connected to a 20 amp branch
circuit any items in addition to the ML27 must not exceed 4 amps.
Adjust only those controls that are specified in these Operating Instructions.
Do not attempt to service or repair the laminator yourself. Unplug the laminator
from the electrical outlet and contact an authorized service representative under
any of the following conditions:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled into the laminator or it has been exposed to water.
• If the laminator has been subjected to excessive jarring through being
dropped or bumped.
• If the laminator does not operate normally when following the operating in-
structions.
• KEEP THE LAMINATOR OUT OF THE REACH OF CHILDREN.
INTRODUCTION
Congratulations on your purchase of the ML27 Roll Laminator. This unit is designed
to provide years of trouble-free service.
The ML27 will accept rolls of laminating film up to 27” wide in all film thicknesses.
Paper and card stock up to 1/16” (1.6mm) thick may be laminated
without adjusting the rollers.
2
1-800-543-5454 www.officezone.com
OfficeZone
Your ML27 is preset at the factory for most applications so any adjustments should be mi-
nor. A LCD readout provides continual indication of the Heat Shoe temperature which may
be adjusted as needed.
Laminator Standard Features...
Preset laminating roller pressure and speed require no adjustment.
Feed table with adjustable guide.
LCD readout for ease in monitoring temperature.
Teflon® coated Heat Shoes for easy cleaning.
Laminating film widths up to 27” (68.6cm).
Total material thickness up to 3/16” (4.8mm) with roller adjustment.
SPECIFICATIONS
Plastic Width 27” (68.6cm)
Plastic Thickness 1.5 mil up to 10mil (37 to 250 micron)
Maximum Roll Length 1.5 mil - 1,000 feet (304.8 meters)
3 mil - 500 feet (152.4 meters)
5 mil - 250 feet (76.2 meters)
10 mil - 100 feet (30.5 meters)
Speed 0-10 feet per minute (3m/minute)
Net weight 97.5lbs (44kg)
Power Requirements 120VAC, 60Hz, 1800 watts
220VAC available
3
1-800-543-5454 www.officezone.com
OfficeZone
INITIAL SETUP
Unpacking...
Before unpacking the unit, inspect the shipping container for signs of damage. Notify
the carrier and your dealer immediately if any damage is noted.
CAUTION! The laminator, weighs approximately 98lbs.
Use two people when removing the laminator from the
shipping container.
Components...
Figure 1 below shows the location of the major components and controls of the
ML27. You should become familiar with these before operating the laminator.
Figure 1
4
1-800-543-5454 www.officezone.com
OfficeZone
Motor Switch: This switch controls power to the Laminating Rollers. If the switch is
pressed to the FWD (light will come on) position the rollers move forward, pulling the
plastic film and laminated material past the Heat Shoes.
Reverse Switch: This toggle switch is found on the back of the machine. When this
switch is pressed to the reverse position and the motor switch is on, the rollers move
in the reverse direction. This is useful for clearing film from the rollers.
Fan Switch: This switch turns the fans on and off. (Switch will be lighted when the
fans are on).
Heater Switch: This switch turns power to the top and bottom Heat Shoes on and off.
(Switch will be lighted when the heaters are on).
Heat Indicator: This light goes on when the Heat Switch is first turned on then
remains on until the Heat Shoe reaches the operating temperature. After that point,
the light will flash periodically as the thermostat controls the Heat Shoe temperature.
OPERATION
This section describes the operation of your ML27. This laminator is designed for all
widths of plastic up to 27”. However, if narrower widths are used the Heat Shoes must
be cleaned before using a wider roll. Refer to the MAINTENANCE section for cleaning
instructions.
Loading Laminating Film onto Mandrels...
Slide the film onto the mandrel as in figure 2 below. Note that one mandrel is labeled
TOP and the other BOTT (for bottom). They are not interchangeable.
Figure 2
5
1-800-543-5454 www.officezone.com
OfficeZone
Threading Laminating Film...
These instructions apply to poly-in film rolls (shiny side out, dull side in).
1. For the top supply roll place the mandrel ends into the slots in the top of the laminator. If
you are facing the front of the laminator the film should unwind toward you from the
bottom of the roll as in figure 3 below.
Figure 3
2. Pull 6”-12” of film from the top roll. Pass the film under the idler bar, heat shield and over
the heat shoes. Make sure the shiny side of the film is against the shoes. See figure 5&6 be
low.
3. For the bottom supply roll, remove the feed table. Place the mandrel ends into position in
the lower mandrel holder slots. If you are facing the front of the laminator the film should
unwind away from you from the bottom of the rollers as shown in figure 4 below.
Figure 4
4. Pull 6”-12” of film from the bottom roll. Pass it under the lower idler bar. You can “drop-
down” the lower idler bar to give you more clearance. After doing so, return the idler bar to its
upper position for running the machine. Drape the film from the bottom roll over the film from
the top roll. See figures 5&6 below.
NOTE: The shiny side of the film must always go against the
Heat Shoes.
CAUTION! The Heat Shoes reach a temperature of up to 350°F.
Do not touch the surface of the Heat Shoes.
Figure 5 Figure 6
6
1-800-543-5454 www.officezone.com
OfficeZone
Table des matières
Autres manuels Office Zone Plastifieuse
