OEM Tools 24987 Manuel de service

UNPACKING

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose,

missing, or damaged parts. If any damage is observed, a shipping damage claim must be ﬁled with the carrier. DO

NOT use the OEMTOOLS®Sidekick Creeper Stool if broken, bent, cracked or damaged parts (including labels)

are noted. Any Rolling Stool that appears damaged in any way, operates abnormally or is missing parts should be

removed from service immediately. If you suspect that the Rolling Stool was subjected to shock load (a load that was

dropped suddenly, unexpectedly, etc.), immediately discontinue use until it has been checked by a factory authorized

service center.

Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and

others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal

injury and/or damage to product or property. Please retain instructions for future reference.

Operating Instructions and Parts Manual 24987

FOR CUSTOMER SERVICE

Technical Question?

CALL 1-866-458-2472

[email protected]

Thank you very much for choosing an OEMTOOLS®Product!

For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:

Model: _______________ Purchase Date: ___________

Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product

before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues

arising from modiﬁcation. We strongly recommend that this product is not modiﬁed and/or used for any application other than that

for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have ﬁrst

contacted customer service to determine if it can or should be performed on the product.

WARNING:This product can expose you to chemicals, including DEHP and lead, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

SIDEKICK CREEPER STOOL

7/21

2021 OEMTOOLS®

Operating Instructions and Parts Manual 24987

7/21

2021 OEMTOOLS™

SIDEKICK CREEPER STOOL

IMPORTANT INSTRUCTIONS

AND SAFETY RULES

1. Know your product. Read this manual carefully. Learn

the product’s applications and limitations, as well as

potential hazards speciﬁc to it.

2. Keep work area clean and well lit. Cluttered or dark

work areas invite accidents.

3. Keep children away. All children should be kept away

from the work area. Never let a child handle tools or

equipment without strict adult supervision.

4. DO NOT operate this product if under the inﬂuence of

alcohol or drugs. Read warning labels on prescriptions

to determine if your judgment or reﬂexes are impaired

while taking drugs. If there is any doubt, DO NOT

attempt to operate.

5. Use safety equipment. Eye protection should be worn at all

times when operating this tool. Use ANSI approved safety

glasses. Everyday eyeglasses are NOT safety glasses. Dust

mask, non-skid safety shoes, hard hat or hearing protection

should be used in appropriate conditions.

6. Wear proper apparel. Loose clothing, gloves, neck-ties,

rings, bracelets or other jewelry may present a potential

hazard when operating this product. Keep all apparel

clear of the product.

7. DO NOT overreach. Keep proper footing and balance

at all times when operating this product.

8. Check for damage. Check equipment regularly. If part of

the product is damaged, it should be carefully inspected

to make sure that it can perform its intended function

correctly. If in doubt, discontinue use of product.

9. Keep away from ﬂammables. DO NOT attempt to operate

this product near ﬂammable materials or combustibles.

Failure to comply may cause serious injury or death.

10. Store this product out of the reach of children and

untrained persons. This product may be dangerous in

the hands of untrained users.

11. Keep this product dry and clean.

12. Use only accessories that are recommended by the

manufacturer for your model. Accessories that may be

suitable for one product may become hazardous when

used on another product.

13. Service must be performed only by qualiﬁed repair

personnel. Service or maintenance performed by

unqualiﬁed personnel could result in a risk of injury.

14. When servicing a product, use only identical replacement

parts. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of injury.

15. Maintain a safe working environment. Keep the work

area well lit. Make sure there is adequate surrounding

workspace. Keep the work area free of obstructions,

grease, oil, trash, and other debris. DO NOT use this

product in a damp or wet location.

16. Maintain labels and nameplates on this product. These

carry important information. If unreadable or missing,

contact OEMTOOLS®for a replacement.

17. Keep this product dry, clean, and free from brake ﬂuid,

oil, and grease.

18. Avoid accidental ﬁre. DO NOT smoke near this product.

19. The warnings, precautions, and instructions discussed

in this manual cannot cover all possible conditions

and situations that may occur. The operator must

understand that common sense and caution are factors

which cannot be built into this product, but must be

supplied by the operator.

20. We believe the information contained herein to be

reliable. However, general technical information is given

by us without charge and the user shall employ such

information at their own discretion and risk. We assume

no responsibility for results or damages incurred from

the use of such information in whole or in part.

21. The manufacturer declines any and all responsibility

for property damage or injury if said damage is the

result of unskillful handling by the operator or of

failure to observe the basic safety rules set forth in the

instruction manual.

22. The procedures documented in this manual are to

serve as guidelines for the use of this equipment.

23. The use of this equipment is simple and straightforward

if you follow the instructions. When operating this

equipment, use common sense, and only use this

equipment for its intended purpose.

PRODUCT DESCRIPTION

The OEMTOOLS®24987 Sidekick Creeper Stool is designed for easy

access to tools and supplies. Large open trays allow user to carry a

wide range of items with additional holster caddies on the side for

rapid access to the user’s items. The slide out under seat drawer can

be used to store and organize smaller items.

PRODUCT SPECIFICATIONS

Length 17.72"

Width 14.96"

Height 14.96"

Weight 20.9 Lb.

Weight Capacity 300 Lb.

SPECIFIC SAFETY INSTRUCTIONS

AND WARNINGS

1. DO NOT place under automobile tires to move or

reposition vehicle.

2. DO NOT use as a toy or skateboard.

3. DO NOT stand on unit or use as a stepping device.

4. DO NOT use if one or more wheels are inoperative.

Repair before re-use.

5. DO NOT use if any part of the support structure is

broken, split or cracked.

6. When not in use, unit should be stored in a secure

place.

7. Always store in an upright position.

8. Keep out of the reach of children.

ASSEMBLY

1. Put the screw (#7) go through the hole of the caster (#5)

then go through the hole of plastic body (#1).

2. Put the sleeve (#6) through the screw (#7).

3. Settle the caster with ﬂat washer (#4) and nut M6 (#3).

Operating Instructions and Parts Manual 24987

7/21

2021 OEMTOOLS™

SIDEKICK CREEPER STOOL

Figure Description Qty.

Seat Cover 1

2Seat Creeper Frame 1

3, 4, 6, 7 Removable Trays 5

5Nuts 4

8Wheels 4

NOTE:Not all components of the Sidekick Creeper Stool are replacement items, but are illustrated as a convenient reference for location and

position in the assembly sequence. The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual as

a reference tool only. Neither the manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is

qualiﬁed to make any repairs to the product, or that he or she is qualiﬁed to replace any parts of the product. In fact, the manufacturer and/or

distributor expressly states that all repairs and parts replacements should be undertaken by certiﬁed and licensed technicians, and not by the

buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out

of his or her installation of replacement parts thereto.

Operating Instructions and Parts Manual 24987

7/21

2021 OEMTOOLS™

SIDEKICK CREEPER STOOL

3580 E. Raines Road, Suite 3, Memphis, TN 38118

Tel: 1-866-458-2472

www.oem-tools.com

OEMTOOLS®ONE YEAR WARRANTY

For up to one year from the date of purchase of this OEMTOOLS®product, if you ﬁnd any defect in material or workmanship (through normal usage),

return it to the place of purchase or to OEMTOOLS®for repair or replacement at our discretion. In order to obtain this service, send the product and

proof of purchase (transportation pre-paid) to:

OEMTOOLS®Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.

We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection veriﬁes the defect, we will

either repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We

will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our

warranty, then you must bear the cost of returning the product.

OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any warranty for products

subjected to abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized or unreasonable use or

repairs. This warranty does not cover bits, blades, ﬁles, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace

blades, bits, ﬁles, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction or design at any time without any

obligation in incorporating such changes to tools or equipment previously sold.

OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser that

this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not apply

to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the