Octava HD70STP-EX Manuel utilisateur
1
HD70STP-EX
Installation Guide
2
Contents
Description...................................................................... 3
Features ......................................................................... 4
Application Diagram........................................................ 4
Front and Back Panel..................................................... 5
Installation....................................................................... 6
Ethernet cable installation recommendations ................. 7
IR Configuration.............................................................. 8
IR Emitter........................................................................ 9
LED Indicator.................................................................. 9
Serial Data(RS232)....................................................... 10
Mounting Tabs.............................................................. 11
Warranty....................................................................... 12
Disclaimers................................................................... 12
Specifications................................................................ 13
3
Description
The HD70STPEX HDMI extender simplifies HD video connectivity using 1
CAT6 cable. The HD70STP is a multi-format extender that extends 1080p,
4x2k ultra HD, 3D video and Advanced bitstream multichannel audio
formats 200ft on 1 single CAT 6 cable..
The HD70STPEX also extends IR, RS-232 controls and PoE power thus
simplifying installations while delivering high quality uncompressed 1080P
HD video and audio
Utilizes Power over Ethernet , PoE, to directly power the connected
HDSTP-70-RX receiver thus allowing clean and compact installations.
Bi-directional IR and RS-232 extension enable easy integration and
control of all connected devices via remote or 3rd part control systems.
Features
Extend HD video over 1 single CAT6 cable up to 200ft
Native uncompressed 1080P, and common 3D resolutions
supported
4K2k Ultra HD video resolution
Dolby Digital, DTS, Dolby Tru HD, DTS Master Audio pass thru.
Power over Ethernet, PoE, provides power to Zone Receiver
unit
Bi-Directional IR
Wideband IR 20-60 KHz circuitry for maximum IR remote
compatibility.
CEC passthru
RS-232 extension for controlling display device.
4
Application Diagram
5
Front and Back Panel
1
HDMI In
connect to video source
2
HDMI Out
connect to display
3
CAT6
Link TX unit with RX unit
4
IR RX
IR Receiver port
5
IR TX
IR Emitter port
6
Power In
Power Input. Powers transmitter
and Zone Receiver unit.
7
RS-232
Serial Port connection.
8
Power and Data LED
indicator
See page 9.
2.HDMI Out
1.HDMI In
3. CAT6
4. IR RX Port
7. RS-232 port
6. Power In
5. IR TX Port
HD70STP-TX
HD70STP-RX
8. LED indicator
6
Installation
HD70STP-TX(transmitter)
HD70STP-RX(receiver)
Installation Procedure
1
Connect “CAT6” of the Transmitter and Receiver
with CAT6 cable. (see page 7 for cable recommendations.)
2
Connect HD source to HDMI In of Transmitter unit
3
Connect Display to HDMI out of Receiver unit
4
IR connection(optional)-configure and connect as shown in
section: “ IR Configuration” (see page 8)
5
Serial connection(optional)-configure and connect as shown in
section: “Serial Data (RS-232)” (see page 10)
6
Connect power supply to the Transmitter
7
Verify that the PWR LED and Data LED Indicator are ON.
(see page 9)
8
Turn on Source and Display.
7
Ethernet cable recommendations
Using Shielded CAT6 (STP, 24AWG or better) or CAT7 cable will
ensure maximum signal integrity plus optimum rejection of external
interference.
Note 2- Unshielded CAT5e and CAT6 cables can be used with your
Octava system though they may result in limiting the maximum
attainable distance depending on quality of cable.
Cable Type
Note
1
CAT7 cable is recommended.
24AWG or better
Best
2
Shielded(STP) CAT6 cable is
recommended. 24 AWG or better
Recommended
3
UTP CAT5e/CAT 6 cable
Acceptable. Note 2
U Use EIA/TIA-568-B standard when terminating your LAN cables.
Ethernet cable installation recommendations:
Use your cable suppliers recommended RJ-45 connector/crimp tool
with your CAT5e, CAT6 or CAT7 cables and ensure you pay particular
attention to the quality of the termination on all cables.
DO / Recommend
Use shielded CAT6 or CAT7 with good RJ-45 terminators
Use a direct cable connection between the Transmitter and
R Receiver unit.
DO NOT
Do Not connect thru Ethernet switches or routers
For optimum signal integrity avoid passing your signals
though any form of Patch-panel, Wall-plate or punch-down
terminations.
Do Not connect cables thru extraneous RJ-45 couplers, wall
plates.
Do Not tightly coil /loop the Ethernet cables
8
IR Configuration
I.R. can be sent in 2 directions:
1) from Receiver to Transmitter or
2) from Transmitter to Receiver unit.
For proper operation, it is recommended that only Octava supplied
I.R. emitter and receiver cables be used.
Configuration 1: Sending IR from Receiver to Transmitter Unit
Connect IR Emitter to IR TX port
Connect IR Receiver to IR RX port
Configuration 2: Sending IR from Transmitter to Receiver Unit
Connect IR Receiver to IR RX port
Connect IR Emitter to IR TX port
9
IR Emitter
An IR Emitter cable has been included with your Octava Product.
The IR emitter cable enables you to control your source using I.R.
remote control.
1
Locate the IR receiver on
the video source. Note, you
may need to refer to your
source data sheet.
2
Remove the double sided
tape on the IR Emitter
3
Place the Emitter head over
the source IR receiver
LED Indicator
1
Normal operation:
Pwr LED =solid green,
Data LED =solid yellow
2
Lost Link:
Pwr LED =solid green,
Data LED =flashing yellow or off
3
No connection
10
Serial Data (RS-232)
Serial control data can be sent using the RS-232 ports from
Transmitter to Receiver unit for controlling the attached display.
A 3 pin Phoenix connector is provided to connect with a RS-232
serial cable. Prepare your serial cable according to diagram below
The following shows the cable configuration for sending serial
commands from the TX to the RX ( display side).
Sending Serial Commands from TX unit to RX Unit.
Serial Port cable
( TX side)
Controller
Side
Serial Port cable
( RX side)
Table des matières
Autres manuels Octava Extenseur
