Nvent RAYCHEM RayClic-E Manuel utilisateur

DESCRIPTION

This end seal is for use with nVent RAYCHEM IceStop, XL-Trace,

HWAT and RaySol heating cables. Materials for one end seal

termination are included in this kit. The appropriate nVent

RAYCHEM power connection kit must also be used. These

installation instructions should be used in conjunction with the

IceStop, XL-Trace, HWAT and RaySol System Installation and

Operation Manuals. For technical support contact your nVent

representative or call nVent (800)545-6258.

Note: The nVent RAYCHEM RayClic-E end seal can be installed

only once; it cannot be removed from the heating cable. Do not

use until ready for final installation.

TOOLS REQUIRED

• Utility knife

• Diagonal cutters

KIT CONTENTS

Qty Description

1 Gel-filled end seal

APPROVALS

With HWAT, IceStop, and

XL-Trace heating cables

Class I, Div. 2, Groups A, B, C, D

hazardous locations with GM-XT only

718K Pipe Heating Cable

877Z De-Icing and Snow Melting

Not UL Listed with XL-Trace

heating cable for buried piping

APPROVED

-w

RayClic-E

RayClic End Seal Kit Installation Instructions

This component is an electrical device that

must be installed correctly to ensure proper

operation and to prevent shock or fire. Read

these important warnings and carefully follow

all the installation instructions.

• To minimize the danger of fire from

sustained electrical arcing if the heating

cable is damaged or improperly installed,

and to comply with the requirements of

nVent, agency certifications, and national

electrical codes, ground-fault equipment

protection must be used. Arcing may not be

stopped by conventional circuit breakers.

• Bus wires will short if they contact each

other. Keep bus wires separated.

• The black heating cable core is conductive

and can short. It must be properly insulated

and kept dry.

• Component approvals and performance are

based on the use of nVent-specified parts

only. Do not use substitute parts or vinyl

electrical tape.

• Use only fire-resistant insulation materials

such as fiberglass wrap.

• Leave these instructions with end user for

reference and future use.

WARNING:

HWAT IceStop, XL-Trace, and RaySol

• Score down and around outer

jacket 1 inch from the end.

• Remove the outer jacket.

• Do not cut or damage inner jacket.

• Using wire cutters, cut away aluminum wrap close to

braid and outer jacket.

• Remove exposed braid.

• Push end seal completely onto heating cable.

Note: The end seal can be

installed only once; it cannot

be removed from the heating

cable. Do not use until ready

for final installation.

nVent reserves the right to change specications without notice.

Raychem-IM-H55428-RayClicE-EN-1805

nVent.com

North America

Tel +1.800.545.6258

Fax +1.800.527.5703

[email protected]

Europe, Middle East, Africa

Tel +32.16.213.511

Fax +32.16.213.604

[email protected]

Asia Pacific

Tel +86.21.2412.1688

Fax +86.21.5426.3167

[email protected]

Latin America

Tel +1.713.868.4800

Fax +1.713.868.2333

[email protected]

Autres manuels nvent Câbles et connecteurs

nvent

nvent Raychem C25-100 Manuel utilisateur

nvent

nvent RAYCHEM HWT-P Manuel utilisateur

nvent

nvent RAYCHEM BTV Manuel

nvent

nvent RAYCHEM Manuel utilisateur

nvent

nvent Raychem E-50-F Manuel utilisateur

nvent

nvent Raychem GM-2CW Manuel utilisateur

nvent

nvent raychem ETL-GLAND-01 Manuel utilisateur

nvent

nvent Raychem IEK-25-PIPE Manuel utilisateur

nvent

nvent Raychem C20-01-F Manuel utilisateur

nvent

nvent Raychem C25-100-FHP Manuel utilisateur

nvent

nvent RAYCHEM H908 Manuel utilisateur

nvent

nvent Raychem E-150-F Manuel utilisateur

nvent

nvent Raychem E-100-L-E Manuel utilisateur

nvent

nvent LENTON Manuel utilisateur

nvent

nvent JBS-PI-EP Manuel utilisateur

nvent

nvent Raychem E-100-E Manuel utilisateur

nvent

nvent RAYCHEM C25-100-METAL-FHP Manuel utilisateur

nvent

nvent Raychem CCON25-100 Manuel utilisateur

nvent

nvent Raychem TraceTek TT-7000-HUV-CK-MC-M Manuel utilisateur

nvent

nvent RAYCHEM E-100-L Manuel utilisateur

nvent

nvent Raychem JBM-100-E Manuel utilisateur

nvent

nvent Erico Ericore Manuel utilisateur

nvent

nvent Raychem JBM-100-EP Manuel utilisateur

nvent

nvent Raychem C25-100-METAL Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur

nvent RAYCHEM RayClic-E Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques