Numatic TT 1840 Manuel utilisateur

Owner Instructions

Warning! Read instructions before using the machine

www.numatic.com

TT 1840

Scrubber Dryer

Machine Overview

1. Operator control panel

2. On / Off Lever

3. Waste water tank

4. Clean water tank

5. Brush deck

6. Squeegee blades

7. Floor-tool retaining knobs

8. Clean-water on / off tap

9. Clean-water emptying cap

10. Rear moving wheels

11. Floor-tool vacuum hose

12. Vacuum hose

13. Separator

14. Clean-water ller cap

15. Clean-water level indicator

16. Clean-water tank ll point

17. Top tank (waste water) drainage hose

18. On / Off Switch

19. Vacuum Switch

20. Pump Switch

21. Power Light

22. Handle Position lever

112

Fill using a hose, bucket or a suitable container. (Fig 5).

Please read before commencing any operation.

After the removal of all the packaging, carefully open and check the contents. !

Using the handle position lever, move the handle into the

upright position. (Fig 1).

Fit the Brush / Pad (Fig 2).

Swing the oor tool carrier from

behind the brush. (Fig 3).

Use the two locking knobs tted to the oor tool, secure to the

oor tool to the oor tool carrier. (Fig 4).

Fill the clean-water tank to a Max of 18 litres

(see page 5)

For operation and cleaning controls

(see page 9)

Quick Set-Up Guide

Tip the machine.

(see Page 4)

Machine Set-Up

Fitting the brushes

Slide the brush / pad under the brush deck (Fig 6).

Featuring the Nulock brush system.

The brush is tted simply by pushing and twisting to lock in place, making tting and removal a simple process.

Fit the brush / pad onto the Nulock drive chuck, twist to lock

the brush / pad in place (Fig 7).

Only use manufacturer supplied brushes.

This machine requires a 400mm brush or a 360mm pad.

Safety gloves are recommended for the changing of used brushes.

Tipping the Machine

Filling the clean-water tank

The TT1840 is equipped with

a large 18 litre clean water

tank allowing large areas to be

cleaning in a single ll.

To ll the clean water tank,

remove the ller cap (Fig 10).

Fill using a hose, bucket or a

suitable container. (Fig 11).

Note: Great care must be taken to ensure that contaminants (leaves,hair, dirt, etc)

are not allowed to enter the clean-water tank during the lling process.

If using a bucket or similar, ensure it is always clean and free from debris.

Machine Set-Up

Fitting the Floor Tool

The oor tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-off

feature if the oor tool gets snagged, whilst in transit.

The oor tool carrier can be

raised and locked from moving

by operating the locking lever,

upwards and backwards.

This lever can be found next to

the lower section of the handle.

Unlock and swing the oor tool

carrier to the side of the machine

(Fig 8).

Secure to the carrier using the

two knobs tted to the oor tool

carrier (Fig 9) - (Fig 9a).

Do not over tighten the retaining

knobs.

Note: It is easier to t the oor-tool if the weight of the machine is resting on the brush.

Ensure the brush is tted rst.

Note: The lever moves upward and backward motion to lock the oortool in the raised position.

Control of Substances Hazardous to Health (COSHH)

For best results use a non-foaming type of chemical, dilute to the manufacturer’s specication.

For further guidance on hazardous substances refer to health and safety instructions online.

Visit http://www.hse.gov.uk/ for UK information.

Water Flow Adjustment

Located on the left of the machine is the On / Off water tap

(Fig 14 / 15).

Pre-cleaning advice.

Important

Do not operate machine unless the Operator Manual has been read and fully understood.

Before performing the cleaning operation, place out

appropriate warning signs and sweep or dust-mop the oor (Fig 16).

WHEN HANDLING AND MIXING CHEMICALS

Always ensure that chemical manufacturer’s safety guidelines are followed.

Only use chemicals recommended for use in auto scrubber-dryers.

Numatic part (629044) Wet Floor sign

(available if required)

Machine Set-Up

Fill Level Indicator

Fill the clean water tank to a maximum of 18 litres, including cleaning chemicals if required.

Follow chemical manufacturing guide lines.

Use the ll indicator

(Fig 12).

Showing the clean water tank full

(Fig 13a).

Showing the clean water tank empty

(Fig 13).

13a

Moving the machine

CAUTION

When moving or lifting the TT 1840, follow the national safety guidelines on lifting.

! !

When the bottom tank (clean water) is full the machine can be

tilted to a maximum of 450(Fig 19).

When the top tank (waste water) is full the machine can be

tilted to a maximum of 100for transporting to dumping area

(Fig 18).

CAUTION

Ensure both tanks are empty before attempting to lift the machine.

! !

Transport the machine by tilting back on to the main transit

wheels (Fig 17).

Weight of empty machine 38.5Kg (85 lbs) (Fig 20).

Machine Set-Up

Pre-scrub mode

The TT1840 has been designed to cope with a variety of oor types and different levels of soiling.

On heavily soiled oors use a ‘double scrub’ technique.

First pre-scrub the oor with the oor tool in the raised position (Fig 21), allow the chemical time to work, then scrub

the area a second time with the oor tool lowered.

To raise the oor-tool, ensure the oor tool carrier is central to the machine (Fig 22).

Lift the lever near the base of the handle and lock into position (Fig 23).

The clean-water / chemical mix

is dispersed via ‘THRU-FEED’

system. The waste water is then

retrieved by the oor tool

Overlap the scrubbing path by

10cm to ensure an even clean

(Fig 24).

If streaking occurs, wipe the oor

tool blades clean (Fig 25).

Floor tool in use

Note: Care must be taken to reduce speed when cornering or when manoeuvring around obstacles.

Note: The lever moves upward and backward motion to lock the oor tool in the raised position.

Machine Operation

1 1

Setting the cleaning controls

To start: hold down either trigger and press the yellow start button once

Ensure your TT1840 machine has been plugged into a suitable power supply.

Select the desired function using the ON / OFF switches tted to the handle.

Vac Switch Pump Switch

Note: The Pump Switch will only function when the Brush is in operation.

20.020.0

ST_Numatic_A4.slddrt 20030224

THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF NUMATIC INTERNATIONAL LTD. AND MUST

NOT BE USED WITHOUT THEIR KNOWLEDGE NOR COMMUNICATED TO ANY PERSON OR COMPANY.

TITLE:-

DIMNs IN

MILLIMETERS

NOT

SCALE

FINISH:-

ITEM No(s):-

DRG No:-

TOLERANCES:-

(UNLESS OTHERWISE STATED)

DRAWN:

DATE:

APPD:

REVISION:

CHANGE DETAIL:

Numatic

INTERNATIONAL LTD

THIRD ANGLE PROJECTION

STRESS RELEIF ARTWORK ASM

RVT

MATERIAL:-

27/05/2009

DRW-21826

SIZE

LINEAR: 0 DECIMAL PLACE = +/- 1.0mm

1 DECIMAL PLACE = +/- 0.25mm

2 DECIMAL PLACES = +/- 0.05mm

ANGULAR:-

+/- 0.5 DEGREE

THE EXAMPLE SHOWN DETAILS THE METHOD USED FOR

IDENTIFYING CRITICAL (INSPECTION) DIMENSIONS WHERE APPLICABLE

MILLFIELD ROAD, CHARD, SOMERSET

TA20 2GB ENGLAND

A01

TOOL NUMBER:

WEIGHT:

All components must be ROHS compliant.

Internal Code:

DEV

Provisional

20.020.0

ST_Numatic_A4.slddrt 20030224

THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF NUMATIC INTERNATIONAL LTD. AND MUST

NOT BE USED WITHOUT THEIR KNOWLEDGE NOR COMMUNICATED TO ANY PERSON OR COMPANY.

TITLE:-

DIMNs IN

MILLIMETERS

NOT

SCALE

FINISH:-

ITEM No(s):-

DRG No:-

TOLERANCES:-

(UNLESS OTHERWISE STATED)

DRAWN:

DATE:

APPD:

REVISION:

CHANGE DETAIL:

Numatic

INTERNATIONAL LTD

THIRD ANGLE PROJECTION

STRESS RELEIF ARTWORK ASM

RVT

MATERIAL:-

27/05/2009

DRW-21826

SIZE

LINEAR: 0 DECIMAL PLACE = +/- 1.0mm

1 DECIMAL PLACE = +/- 0.25mm

2 DECIMAL PLACES = +/- 0.05mm

ANGULAR:-

+/- 0.5 DEGREE

THE EXAMPLE SHOWN DETAILS THE METHOD USED FOR

IDENTIFYING CRITICAL (INSPECTION) DIMENSIONS WHERE APPLICABLE

MILLFIELD ROAD, CHARD, SOMERSET

TA20 2GB ENGLAND

A01

TOOL NUMBER:

WEIGHT:

All components must be ROHS compliant.

Internal Code:

DEV

Provisional

ALWAYS ENSURE THAT THE POWER SUPPLY IS DISCONNECTED,

PRIOR TO ANY MAINTENANCE OPERATION.

! !

After use, empty waste water tank using

emptying hose and ush out with clean

water. A

Remove the two hoses and disconnect the

separator from the machine (Fig 26). Undo

the separator restraining strap (Fig 26a) and

lift off the separator. The separator has a

sealing rubber which should be examined at

every clean down (Fig 27).

Rinse using clean water.

Note:

Avoid over tightening the clean water draining cap.

The TT1840 has been designed with ease of use in mind, this included easy stripping down and cleaning.

Remove the two lters clipped into the separator and ush with clean water (Fig 28)(Fig 29).

Replace by tting the rear of the lter rst then clipping the front to lock in place (Fig 30) (Fig 31).

Once emptied the top waste water tank can simply be lifted off. (Fig 32).

The clean water tank can be drained via the yellow cap tted to the left

hand side of the machine. The cap has a rubber seal and might require a

spanner to remove. (Fig 33).

Regular Maintenance

26a

Autres manuels pour TT 1840

Table des matières

Autres manuels Numatic Scrubber

Numatic

Numatic CRO 8055/100T Manuel utilisateur

Numatic

Numatic TGB 2228 Manuel utilisateur

Numatic

Numatic CRO 8072 Manuel utilisateur

Numatic

Numatic TGB 6055/100 Manuel utilisateur

Numatic

Numatic CRO 8055 Manuel utilisateur

Numatic

Numatic HGB 3045 Manuel utilisateur

Numatic

Numatic TTB 1840 36V Manuel utilisateur

Numatic

Numatic TT 1840G Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

Numatic

Numatic NX 1K Manuel utilisateur

Numatic

Numatic TRG 720/200T Manuel utilisateur

Numatic

Numatic TT 1535S Manuel utilisateur

Numatic

Numatic TTB 1840 36V Manuel utilisateur

Numatic

Numatic NTT 2003 Manuel utilisateur

Numatic

Numatic TT-4550S Mode d’emploi

Numatic

Numatic TTB-4500/100S Mode d’emploi

Numatic

Numatic HGB 3045/55 Manuel utilisateur

Numatic

Numatic TT 1840 Manuel utilisateur

Numatic

Numatic TRO 650/200T Manuel utilisateur

Numatic

Numatic HT4045 Manuel utilisateur

Numatic

Numatic TT 6650S Manuel utilisateur

Numatic

Numatic NX 1K TBL4045 Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

Numatic

Numatic TGB 516 36V Manuel utilisateur

Manuels Scrubber populaires d'autres marques

Olympus

Olympus M200H Manuel utilisateur

Clarke

Clarke BEXT 100H Manuel d'installation et d'exploitation

JOHNY VAC

JOHNY VAC JVC70BCT Manuel utilisateur

RCm

RCm Elan Series Manuel

Kärcher

Kärcher B 120 W Manuel utilisateur

Truvox

Truvox Orbis MotorScrubber 20 Manuel utilisateur

U.S. Products

U.S. Products PEX 500-C-TICK Mode d'emploi

Mclennan

Mclennan C510 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Columbus

Columbus ARA 66 BM 100 Manuel utilisateur

American-Lincoln

American-Lincoln 505-945 Manuel utilisateur

FIORENTINI

FIORENTINI ET 65-75 Manuel utilisateur

Floorpul

Floorpul ruby 48 blt Guide de l'utilisateur

Onyx

Onyx RX-34 Manuel utilisateur

Dustbane

Dustbane Hurricane 400 Manuel utilisateur

Sana

Sana EUJ-702 Manuel utilisateur

REMS

REMS Twist Manuel utilisateur

Tennant

Tennant 7200 Manuel utilisateur