Novus NVIP-5VE-6201 Manuel utilisateur
U ser’s ma n ual
(s h o rt f or m )
NVIP-5VE-6201
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
2
IMPORTANT SAFEGUARDS AND WARNINGS
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING
DIRECTIVES:
Information
The device, as a part of professional VSS system used for surveillance and control, is not designed for
self installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other
devices during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING
THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonization of the laws of the Member
States relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79 - 106, with
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE) (OJ L
97, 24.7.2012, p. 38 - 71,with changes)
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances
in electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88 - 110, with changes)
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual;
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
4
TABLE OF CONTENTS ..................................................................................................... 4
1. FOREWORD INFORMATION ................................................................................... ..5
1.1. General characteristics ......................................................................................... 5
1.2. Technical specification .................................................................................... ...6
1.3. Camera dimensions .......................................................................................... ...7
1.4. Package contents............................................................................................... ...7
2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8
2.1. Description of connectors and control tools ........................................................ 8
2.2. Ethernet cable connecting ................................................................................... 9
2.3. Camera mounting .............................................................................................. 10
2.4. Starting the IP camera........................................................................................ 11
2.5. Initial configuration via the web browser .......................................................... 12
2.6. Security recommendations for network architecture and configuration ......... 13
3. NETWORK CONNECTION USING WEB BROSWER ......................................... 14
3.1. Recommended PC specification for web browser ............................................. 14
3.2. Connection with IP camera via web browser ..................................................... 14
4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 16
4.1. Displaying live video. ........................................................................................ 16
5. FACTORY SETTINGS RESTORING ...................................................................... 17
5.1. Software factory settings restoring via web browser ......................................... 17
5.2. Software factory settings restoring via NMS IPTool……… ... ………………..17
TABLE OF CONTENTS
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
Sensor resolution: 5.0 megapixels
Mechanical IR cut filter (IR operation capability)
Min. Illumination from 0.02 lx
Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions
Built-in webserver: camera configuration through the website
Video compression: H.264, H.265
Max. video resolution up to 2592 x 1944
Electronic Shutter from 1/2 s to 1/100000 s.
Digital Noise Reduction (DNR)
Highlight Compensation (HLC)
Back Light Compensation (BLC)
Reduction of image flicker (Antiflicker)
The compression, resolution, speed and quality can be defined individually for each stream
Supports up to 3 streams
ONVIF Protocol Support
RTSP protocol support for video transmission
ROI zones
Privacy Zones
Range of responses to alarm events: e-mail with attachment, save on FTP server
Video Content Analysis (VCA):
- tamper
- abandoned object
- object disappearance
- line cross
- zone entrance
- scene change
- video color cast
Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
Power supply: 12 VDC / PoE
FOREWORD INFORMATION
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
6
1.2. Technical specification
FOREWORD INFORMATION
IMAGE
Image Sensor 5 MPX CMOS sensor 1/2.7” SmartSens
Number of Effective Pixels 2608 (H) x 1960 (V)
Min. Illumination 0.02 lx/F1.85 - color mode,
0 lx (IR on) - B/W mode
Electronic Shutter auto/manual: 1/2 s ~ 1/100000 s
Digital Slow Shutter (DSS) up to 1/2 s
Wide Dynamic Range (WDR) yes
Digital Noise Reduction (DNR) 2D, 3D
Defog Function (F-DNR) yes
Highlight Compensation (HLC) yes
Back Light Compensation (BLC) yes
Reduction of image flicker (Antiflicker) yes
LENS
Lens Type standard, f=2.8 mm/F1.85
DAY/NIGHT
Switching Type mechanical IR cut filter
Switching Mode auto, manual, time
Switching Level Adjustment yes
Switching Delay 2 ~ 120 s
Switching Schedule yes
Visible Light Sensor yes
NETWORK
Stream Resolution 2592 x 1944, 2560 x 1440 (QHD), 1920 x 1080 (Full HD),
1280 x 720 (HD), 640 x 480 (VGA),
480 x 240, 320 x 240 (QVGA)
Frame Rate 20 fps for 2592 x 1944,
30 fps for 2560 x 1440 (QHD) and lower resolutions
Multistreaming Mode 3 streams
Video/Audio Compression H.264, H.265/G.711
Number of Simultaneous Connections max. 4
Bandwidth 12 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4, IPv4/v6, UDP, HTTPS, Multicast, FTP,
DHCP, DDNS, NTP, RTSP, UPnP, QoS/DSCP, IEEE 802.1X,
PPPoE, SMTP, SSL, ICMP, Unicast
ONVIF Protocol Support Profile S
Camera Configuration from Internet Explorer browser
languages: Polish, English, Russian, and others
Compatible Software NMS, NVR-6000 Viewer
Mobile applications SuperLive Plus (iPhone, Android)
OTHER FUNCTIONS
Privacy Zones 4 video mask type: single color
Motion Detection yes
Region of interest (ROI) 3
Video Content Analysis (VCA) tamper, abandoned object, object disappearance, line
cross, zone entrance, Scene Change, Video Color Cast
Image Processing 180˚ image rotation, sharpening, mirror effect,
vertical flip, horizontal flip
Prealarm/Postalarm -/up to 120 s
System Reaction to Alarm Events e-mail, e-mail with attachment, saving file on FTP server
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
7
FOREWORD INFORMATION
1.3. Camera dimensions (mm)
Camera NVIP-5VE-6201
1.4. Package contents
After opening, make sure that the following elements are inside:
IP camera
Accessories bag
Short version of user’s manual
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not
compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages
caused by the usage of improper power supply source are not covered by the warranty.
95
83
95
IR LED
LED Number 1
Range 30 m
Angle 120°
INTERFACES
Audio Input/Output -/- + built-in microphone
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
INSTALLATION PARAMETERS
Dimensions (mm) 95 (Ф) x 83 (H)
Weight 0.5 kg
Degree of Protection IP 67 (details in the user’s manual)
Enclosure vandalproof IK10 impact rating aluminium, white
Power Supply PoE, 12 VDC
Surge protection TVS 4000 V
Power Consumption 3 W,
6 W (IR on)
Operating Temperature -30°C ~ 60°C
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
8
START-UP AND INITIAL IP CAMERA CONFIGURATION
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches
the temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
2.1 Description of connectors and control tools
1. 100 Mb/s Ethernet port (PoE RJ-45 connector)
2. Power supply 12VDC
3. Base of camera
4. Counter screw
1
2
3
4
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
9
START-UP AND INITIAL IP CAMERA CONFIGURATION
2.2. Ethernet cable connecting
To maintain tightness of ethernet cable connection, please follow instruction below:
1. Unscrew the nut (1) from the connector cover (2).
2. Route the network cable (without the RJ-45 plug) through the components (1) and (2), than crimp the
RJ-45 connector.
3. Plug the RJ-45 connector into the hermetic socket (3), screw the connector cover (2), and than the
nut (1).
CAUTION!
The declared degree of protection of the camera relates to its housing and does not take into
account the possibility of moisture infiltration into the camera by connection cables. Connection
cables protection through i.e. sealing up is the camera installer duty. The manufacturer is not
liable for any camera damages caused as a result of failing in performing that activity by
installer, which also means that camera damaged in that way is not subject to warranty repairs.
CAUTION!
Camera power supply connector is not hermetic. Installer should seal this connector by himself.
Camera can be supplied using external power supply unit corresponding with the camera parameters or
by using RJ45 network socket and PoE (802.3af) power supply unit. If you’re using external power
supply please connect wires according to polarisation shown on picture:
CAUTION!
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
12 VDC +
GND
Schema of 12VDC power supply connector
1 2
3
1
2
NVIP-5VE-6201 - User’s manual (short form) ver 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
10
2.3. Camera mounting
To mount a camera please follow the instructions below:
Unscrew the counter screw (2).
Remove the camera cover (1), remove the camera from the base (3).
Put the bracket to the wall in a desired mounting place (with cable hole). Take the drill pattern
and mark future drilling holes for screws and wires.
Drill holes for screws, wires and base.
Mount the camera base (3) using the supplied plugs and screws.
Connect the camera wires, put camera on the base (3), attach the cover (1) and pre-tighten the
counter screw (2).
Adjust camera position.
Tighten to the stop counter screw (2).
CAUTION!
Please note that the wall or ceiling must have enough strength to carry the IP Camera.
CAUTION!
In order to obtain declared degree of protection please seal the camera bracket to prevent water
getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please
additionally seal the junction with appropriate sealing mass. Please pay special attention to any
mounting holes and if they are a loop-through ones, seal them too.
START-UP AND INITIAL CAMERA CONFIGURATION
3
1
2
Table des matières
Langues :
Autres manuels Novus Caméra de sécurité
Novus
Novus NVIP-5V-6202M Manuel utilisateur
Novus
Novus NVIP-7000 series Manuel utilisateur
Novus
Novus NVC-422H/IR Manuel utilisateur
Novus
Novus NVIP-5000 series Manuel utilisateur
Novus
Novus NVDN-601V/IR-white Manuel utilisateur
Novus
Novus NVIP-5DN2021D/IR-2P Manuel utilisateur
Novus
Novus NVIP-5H-6201 Manuel utilisateur
Novus
Novus NVIP-2VE-6632M Manuel utilisateur
Novus
Novus NVIP-2H-4201 Manuel utilisateur
Novus
Novus NVIP-8VE-4511/FWLAD Manuel utilisateur
Novus
Novus NVIP-5DN3614V/IR-1P Manuel utilisateur
Novus
Novus NVIP-5H-4502M Manuel utilisateur
Novus
Novus NVIP-4DN3516D/IR-1P Manuel utilisateur
Novus
Novus NVIP-3DN7540H/IRH-2P Manuel utilisateur
Novus
Novus NVIP-4VE-6501/F-II Manuel utilisateur
Novus
Novus NVIP-2DN3033V/IR-1P-II Manuel utilisateur
Novus
Novus NVIP-2VE-4231 Manuel utilisateur
Novus
Novus NVIP-4VE-6202-II Manuel utilisateur
Novus
Novus NVAHD-1DN5102H/IR-1 Manuel utilisateur
Novus
Novus NVIP-4V-8002M Manuel utilisateur
