AXI102 / AAP102
18
reasons, the positive control is only activated after a minimum force has been attained. Until this force
is achieved, the expansion process can be interrupted at any time by releasing the start button (1).
The device then automatically returns to its initial position.
Pos: 29 /R VT/K urzbes chr eibung /Entr iegel ungs knopf/ AXI1 02 @ 0\mod_1382426033219_18.docx@ 1414@ 3@ 1
7.1.2Release button (5) (Fig. 1)
The release button (5) is used to return the tool to its initial position before the expansion process has
been completed. In order to do this, press the release button (5) until the expander head (7) has
moved back completely.
Pos: 30 /R VT/ Kur zbes c hr eibung / Pre ssa ut oma ti k/PA--AAP102@ 6\mod_1583245266539_18.docx@ 55489@ 23 @ 1
7.2 AAP102 pusher tool (Fig. 2)
1 Start button
5 Pusher adapter
7 Expander head
14 Battery
7.2.1Automatic press cycle (Fig. 2)
The pusher tool features positive control. During compression, the pusher tool remains in the position
reached, even if the start button (1) is temporarily released. When the intended switch-off force is
achieved, it is perceptible by means of an increase in the motor speed and a discernible decrease in
pressure. When the start button (1) is released, the device returns to its initial position. For safety
reasons, the positive control is only activated after a minimum force has been attained. Until this force
is achieved, the pressing operation can be interrupted at any time by releasing the start button (1).
The device then automatically returns to its initial position.
Pos: 31 /R VT/ Kur zbes c hr eibung / Entr ieg el ung skn op f/AA P1 02 @ 0\mod_1382427863945_18.docx@ 1420@ 3 @ 1
7.2.2Release button (5) (Fig. 2)
The release button (5) is used to return the tool to its initial position before the pressing operation has
been completed. In order to do this, press the release button (5) until the pusher adaptor (7) has
moved back completely.
Pos: 32 /R VT/ Kur zbes c hr eibung /D r ehb arer Kopf /DK--AAP102 @ 1\mod_1448549759659_18.docx@ 15628@ 3 @ 1
7.2.3Rotatable head (Fig. 2)
The pusher tool is equipped with a rotatable head. It cannot be rotating during the pressing operation.
Pos: 33 /R VT/ Kur zbes c hr eibung / Sc hie bea dapt er/ Schi e bead apt er @ 1\mod_1448462990250_18.docx@ 15484@ 3 @ 1
7.2.4Pusher adaptor (Fig. 3)
The nominal width and the name of the system supplier are inscribed on the pusher adapters.
Furthermore, an arrow indicates the installation direction and a number indicates the order. If the
nominal widths for a size are aligned with each other, the arrows and the numbers will be in line.
Pos: 35 /RV T/Kurz bes chr eib ung /A kku allg emei n/Ü ber sc hrif t/A A--ÜS--AC O102, AC O152, AC O202X L, AXI/ AAP10 2, @ 0\mod_1382447195475_18.docx@ 1453 @ 2@ 1
7.3 Battery
Pos: 36 /R VT/K urzbes chr eibung /Akk u allge mein/ Akku ab nehm en + aufse tzen/ AAP/ AXI10 2@ 0 \mod_1402922267408_18.docx@2711 @ @ 1
Removing the battery (Fig. 4)
Push in (1) the two release buttons (A) and then remove the battery (2).
Inserting the battery (Fig. 5)
Slide the battery into the device as illustrated until it clicks into place.
Pos: 37 /R VT/ Kur zbes c hr eibung / Akk u all ge mein/ A kku Z ust ands anz eig e/AC O 102, ACO1 52, AXI/A AP 102 @ 0\mod_1382444821884_18.docx@ 1440@ @ 1
Battery charge indicator (Fig. 1)
The 4 green LEDs (4) indicate the charge level of the battery. The number of LEDs lit up denotes the
battery charge. If the LED (2) is flashing, the battery is empty and no further travel is possible.
Pos: 38 /R VT/Kur zbes chrei bung/ Gerät + Akk u/Info welc her Akk u/12V : AAP/AX I102 @ 0\mod_1402925654215_18.docx@ 2725 @ 2 @1
7.4 AXI102 and battery
Information!
The AXI102 expander and AAP102 pusher tool must only be operated with
12 V DC lithium-ion rechargeable batteries. The 12 V battery must only be used in
the appropriate press devices.
Pos: 39 /R VT/K urzbes chr eibung /Akk u allge mein/ Info: nic ht gel aden + T emper atur en/AA--NG--ACO 102, ACO1 52, ACO /ECO20 2, ACO202 XL, AFP/ EFP20 2, AXI/AA P102 @ 2\mod_1469431352019_18.docx@21590 @ @ 1
