Novalynx 200-WS-01B Manuel utilisateur

200-WS-21-A

User Manual

Dual Set Point Wind Alarm

Phone (530) 823-7185 USA Toll Free (800) 321-3577 Fax (530) 823-8997

Email no[email protected] Website www.novalynx.com

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 2 November 2018

Receiving and Unpacking

Carefully unpack all components and compare to the packing list. Notify NovaLynx Corporation

immediately concerning any discrepancy. Inspect equipment to detect any damage that may have

occurred during shipment. In the event of damage, any claim for loss must be filed immediately with

the carrier by the consignee. Damages to equipment sent via Parcel Post or UPS require the consignee

to contact NovaLynx Corporation for instructions.

Returns

If equipment is to be returned to the factory for any reason, call NovaLynx between 8:00 a.m. and 4:00

p.m. Pacific Time to request a Return Authorization Number (RA#). Include with the returned

equipment a description of the problem and the name, address, and daytime phone number of the

sender. Carefully pack the equipment to prevent damage or additional damage during the return

shipment. Call NovaLynx for packing instructions in the case of delicate or sensitive items. If packing

facilities are not available take the equipment to the nearest Post Office, UPS, or other freight service

and obtain assistance with the packaging. Please write the RA# on the outside of the box.

Warranty

NovaLynx Corporation warrants that its products are free from defects in material and workmanship

under normal use and service for a period of one year from the date of shipment from the factory.

NovaLynx Corporation's obligations under this warranty are limited to, at NovaLynx's option: (i)

replacing; or (ii) repairing; any product determined to be defective. In no case shall NovaLynx

Corporation's liability exceed product's original purchase price. This warranty does not apply to any

equipment that has been repaired or altered, except by NovaLynx Corporation, or that has been

subjected to misuse, negligence, or accident. It is expressly agreed that this warranty will be in lieu of

all warranties of fitness and in lieu of the warranty of merchantability.

Address

NovaLynx Corporation

431 Crown Point Circle, Suite 120

Grass Valley, CA 95945-9531 USA

Phone: (530) 823-7185

Fax: (530) 823-8997

Email: nova@novalynx.com

Website: www.novalynx.com

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 3 November 2018

CONTENTS

1 FORWARD ....................................................................................................................................................................... 4

2 INTRODUCTION ............................................................................................................................................................... 4

3 TECHNICAL SPECIFICATION ............................................................................................................................................. 4

4 PRE-INSTALLATION CHECKOUT ....................................................................................................................................... 5

4.1 Power Supply Connection ....................................................................................................................................... 6

4.2 Menu Navigation ..................................................................................................................................................... 6

4.2.1 MENU Button .................................................................................................................................................. 6

4.2.2 UP and DOWN Buttons ................................................................................................................................... 6

4.2.3 CLEAR Button .................................................................................................................................................. 7

4.2.4 GO Button ....................................................................................................................................................... 7

4.3 Programming........................................................................................................................................................... 7

4.4 DIP Switch Settings .................................................................................................................................................. 7

5 ANEMOMETER INSTALLATION ........................................................................................................................................ 8

5.1 Anemometer Siting Considerations ........................................................................................................................ 8

5.2 Anemometer Mounting .......................................................................................................................................... 8

5.3 Cable Installation..................................................................................................................................................... 9

5.4 Anemometer Wire Diagram .................................................................................................................................... 9

5.5 Anemometer Maintenance ..................................................................................................................................... 9

6 WIND ALARM CONTROLLER INSTALLATION ................................................................................................................. 10

6.1 Controller Location ............................................................................................................................................... 10

6.2 Controller Mounting ............................................................................................................................................. 10

7 CONNECTIONS ............................................................................................................................................................... 11

7.1 Anemometer Connection ...................................................................................................................................... 11

7.2 Power Connection ................................................................................................................................................. 11

7.3 Relay Connections ................................................................................................................................................. 12

8 Alarm Functions ............................................................................................................................................................ 12

APPENDIX A ........................................................................................................................................................................... 13

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 4 November 2018

1 FORWARD

Thank you for purchasing NovaLynx products. NovaLynx has been designing and manufacturing

weather instruments since 1988. NovaLynx represents several well-known brands of quality

manufacturers, including Gill Instruments, RM Young, Kipp & Zonen, and Vaisala. It is our hope that our

products will meet all your monitoring requirements.

2 INTRODUCTION

The 200-WS-21-A Dual Set Point Wind Alarm includes a rotating cup style anemometer (200-WS-01B)

and internal alarm buzzer. Two independently controlled relays are provided to operate external

equipment such alarm lights or sirens. The Wind Alarm can function as an irrigation or fountain over-

ride controller.

The back-lit LCD display is easily visible through the transparent cover. With the cover removed the

unit is programmed by push-button controls without the need to connect a computer. DIP switch

settings select the units (mph or kph) and enable/disable the buzzer.

Each alarm channel has three programmable settings:

Delay before Alarm 0-99 seconds above threshold before alarm activation (Default 15 sec)

Alarm Set Point Wind speed threshold for the alarm (Default 15 mph)

Delay after Alarm 0-99 seconds below threshold before alarm de-activation (Default 15 sec)

When in alarm mode, a blinking LED indicates which relay(s) are active. Each relay can be connected in

the normally open or the normally closed mode. It is the responsibility of the installer to properly

insulate any connections to the relay terminals, especially if high voltages are present. It is also

important to provide an earth grounding wire to protect the controller from static discharge,

whether or not the relays are connected.

3 TECHNICAL SPECIFICATION

The anemometer is rated for wind speeds up to 125 miles per hour and has a starting threshold of

approximately 1.2 mile per hour. The Wind Alarm LCD can display speeds up to 99.9 mph, but the

control logic continues to operate above this limit.

The controller requires a nominal 12V ac or dc power supply. The 200-WS21P power pack (sold

separately) is suitable in most applications, and comes with the proper terminals for easy connection.

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 5 November 2018

200-WS-21-A Dual Set Point Controller Specification

Display LCD, 2x16 characters, 3x8 mm character size, backlit

Indicators Power: Green LED, Alarms: Red LEDs

Setup DIP switch: WIND/TEMP, MPH/KPH, DEG F/DEG C, BUZZER/DISABLE

Programming Pushbutton: MENU, UP, DOWN, CLEAR, GO

Connections All user connections 1/4" male spade terminals (connectors supplied)

Relay specifications Form "C" (SPDT) N.O. and N.C. Contact rating: 3A @ 24Vdc / 115 VAC

Alarm ON / OFF delay range

0 to 99 seconds

Timing accuracy ± 2%

Measurement range 0 to 99.9

Integration interval 2 seconds

Input Power Nominal 12V AC or DC, 50 mA maximum

Operating temperature -20°C to +50°C

Mounting Knock-outs in back surface for screw mounting to a panel

Dimensions 5.12 x 6.25 x 2.95 inch (13.0 x 15.9 x 7.5 cm)

Weight / Shipping 1 lbs (0.45 kg) / 2 lbs (0.9 kg)

200-WS-01B Anemometer Specification

Measurement Range 125 mph max (55.88 m/s max)

Speed Threshold 1.2 mph (0.5364 m/s)

Speed Constant 1.25 mph = 1 Hz (0.5588 m/s = 1 Hz)

Accuracy 1 mph (0.4470 m/s) or ±3%

Transducer Type Reed switch, magnet activated

Maximum Rating 10 mA @ 50 V (ac or dc)

Turning Radius 4 inch (10.16 cm)

Cable 40 feet (12 m), 2 conductor, 24 AWG, shielded, spade plug connectors

Mounting 1.07 inch diameter by 0.82 inch socket (27 mm dia x 21 mm)

(fits standard 3/4" IPS pipe)

Dimensions 4.5 H x 8.5 W inches (12 x 22 cm)

Weight / Shipping 1 lbs (0.45 kg) / 2 lbs (0.9 kg)

4 PRE-INSTALLATION CHECKOUT

The controller can be operated before installation to become familiar with the menus and programming

features. You will need a power supply and the Wind Alarm controller. The sensor and relays will not be

connected for these tests.

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 6 November 2018

4.1 Power Supply Connection

The 200-WS-21P power supply (sold separately) is provided with

¼" spade connectors that fit the terminals at the lower left corner

of the Wind Alarm circuit board. If you are using a different power

supply, use the provided accessory connectors to wire to your 12V

ac or dc power source. Plug the AC Adapter into a wall outlet and

check that the green power LED on the Wind Alarm circuit board

turns on.

The display should look similar to the

illustration on the right. This is the

operating mode screen.

NOTE: If you see the word "Temp:"

instead of "Wind:" then the DIP

switches are in the wrong position.

Refer to the "DIP Switch Settings"

section of the manual to correct this

situation.

4.2 Menu Navigation

Locate the programming buttons below the display.

4.2.1 MENU Button

Press the MENU button. One of the three menus will be displayed (depending on which was viewed

last). Additional uses of the MENU button will be discussed in the following programming section.

4.2.2 UP and DOWN Buttons

Use the UP and DOWN buttons to cycle through the menus.

1. Alarm Delays – the delay (seconds) before and after

an alarm threshold is crossed.

2. Wind Alarms – the set points at which the alarm

occurs.

3. Max Wind Speed – displays the maximum wind speed

recorded since the last time the CLEAR button was

pressed.

MENU UP DOWN CLEAR GO

ACin / DCin

ACin/DCgnd

200-WS-21P

AC Adapter

(sold separately)

(DC+)

(DC-)

Max Wind Speed

0.0 (mph)

Wind Alarms(mph)

1: 15 2: 15

Alarm Delays (s)

ON:15 OFF:15

UP DOWN

A/DM

Menu Up Dn Clr Go

PROGRAMMING

BUTTONS

POWER LED

Wind: 0.0 (mph)

1: 15 2: 15

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 7 November 2018

4.2.3 CLEAR Button

The CLEAR button performs the following actions:

1. If the user is in an editable field, the field will be set to the lowest possible value.

2. If the user is viewing the Max Wind Speed, the recorded value will be erased.

3. If the unit is alarming, all delay counters will be cleared.

4.2.4 GO Button

Press GO from any menu to return to

operating mode.

If the unit is already in operating mode, press GO to pause the system and disable all alarms.

4.3 Programming

Press the GO button until the display shows the operating mode screen (see GO Button, above).

1. Press MENU to enter programming mode. Use the UP or DOWN buttons to reach the Wind

Alarms Menu (see illustration below, left side).

Wind Alarms(mph)

1: 15 2: 15

Wind Alarms(mph)

1: 15 2: 15

Wind Alarms(mph)

1: 15 2: 15

MENU MENU

Wind Alarms Menu Program channel #1 Program channel #2

2. Press MENU again. A blinking block cursor will be displayed on the channel #1 value. (see

Program channel #1, above). Press the UP or DOWN buttons to change the wind speed

threshold for channel #1.

3. Press MENU again. The blinking block cursor will move to channel #2 (see Program channel #2,

above). Press the UP or DOWN buttons to change the value.

4. Press MENU again to get back to the Wind Alarms menu.

5. Press UP to switch to the Alarm Delays menu.

6. Program the alarm delays in the same manner as you did the wind alarms.

7. When you are done setting the alarm delays, press GO to return to operating mode.

4.4 DIP Switch Settings

The DIP switches are pre-set at the factory and should not need to be adjusted. However, sometimes

during installation they get changed accidentally.

1. The Dual Set Point controller is designed to operate as either a Wind alarm or Temperature

alarm. The DIP switch marked "Wt" determines which mode is selected. Set this switch to OFF

for wind alarms.

2. Set the "Wu" switch to OFF for wind speed in miles per hour (MPH). Set the switch ON for

kilometers per hour (KPH).

3. The "Tu" switch sets the temperature units. This is not relevant to the wind alarms, so it doesn't

matter how this switch is set.

Wind: 0.0 (mph)

1: 15 2: 15

System Paused

GO to resume

Operating Mode

Paused Mode

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 8 November 2018

4. The "Si" (silent) switch determines whether the internal buzzer operates. The normal setting is

OFF which allows the buzzer to operate. The ON setting silences the buzzer.

The controller checks the positions of the DIP switches when the unit initializes during power-up. It is

necessary to disconnect the AC Adapter for a few seconds and then re-connect power for the unit to

change modes.

5 ANEMOMETER INSTALLATION

WARNING: Avoid overhead power lines whenever possible. If there are overhead power lines, use

extreme care to prevent contact with the power lines while installing the equipment. NovaLynx

recommends using only experienced equipment installers to avoid injury.

5.1 Anemometer Siting Considerations

Choose a mounting location for the wind sensor that is free of obstructions since nearby objects can

create eddy currents that will affect the wind measurements. Try to locate the wind sensor so that the

nearest object is 10 x T away from the wind sensor mast, where T is the height of the object.

Roof mounted sensors should be placed on the upwind side of the building and away from all exhaust

vents. If the sensor is located on top of a building the sensor height should be 1.5 x H, where H is the

height of the building.

In all cases when the wind sensor data is to be correlated to National Weather Service data or World

Meteorological Organization data, the standard exposure is 33 feet (10 meters) above the ground.

5.2 Anemometer Mounting

CAUTION: Always be careful when working on equipment that is mounted above you. Do not allow

others to stand below when equipment is being installed as falling objects can be hazardous.

The 200-WS-01B anemometer is often mounted to the top of the supporting mast. A mounting arm

(Part number 200-153) is available for mounting to the side of the mast or tower. The base of the

sensor accepts ¾" IPS pipe size or any other 1" to 1-1/16" (25 to 27 mm) outside diameter pipe.

The mast should be easy to reach for servicing the sensor and should be properly anchored and

grounded. A tilt-down arrangement can eliminate the need for lifts or ladders during installation and

service.

If the supporting mast or tower is metal it should be properly grounded to minimize lightning damage.

Installations where nearby lightning strikes are likely should include a properly grounded lightning rod

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 9 November 2018

above the level of the sensor, preferably on a separate tower. It may be necessary in some locations to

contact a local contractor to ensure that local electrical codes have been met by the installer.

Position the wind sensor onto the end of the mast or mounting arm. Secure the sensor to the mast

using the set screws provided in the sensor base. Do not use excessive force when tightening the

screws. Tighten the screws until the sensor base can no longer be manually rotated.

5.3 Cable Installation

The PVC jacket of the cable will last for many years outdoors under normal circumstances. In harsh

environments it may be necessary to protect the cable with conduit.

Route the sensor cable down the mast and to the monitoring equipment in the most direct manner.

Leave a "drip loop" of cable below the entry point to the equipment enclosure to help keep moisture

out. Fasten the cable to the mast with cable ties to prevent whipping during high velocity winds. For

best results, use plastic cable ties that are resistant to ultra-violet radiation and place them at two foot

intervals. Do not over-tighten. Avoid sharp bends, excessive twisting, scrapes and nicks.

5.4 Anemometer Wire Diagram

Speed Signal

Speed Ground

Reed Switch

Red

Black

Clear

Earth Ground

3 PER REV

Wire Diagram for 200-WS-01B Wind Speed Sensor

NOTE: The shield wire in the sensor cable is electrically connected to the shaft holding the bearing /

cup assembly. The purpose is to bleed off static that would otherwise affect the sensor output.

Therefore it is important to earth ground the shield wire for best results.

5.5 Anemometer Maintenance

Wind sensors experience vibration due to high velocity wind. The vibration can loosen the mounting

screws or the support structure. Regular inspection of the mounting hardware is required to prevent

damage to the sensor.

NovaLynx Corporation________________________________________________________________________________

200-WS-21-A Page 10 November 2018

1. Tighten the mounting screws if necessary (do not strip the threads in the plastic base of the

sensor).

2. Spin the anemometer cup assembly. It should turn freely. A short spray of light oil such as

WD40 can be applied to the bearing located in the hub of the cup assembly.

3. Inspect the cable and ensure it is secured to the mast to prevent damage due to wind whipping.

4. A repair kit (Part number 2502-14-10B) is available in case one of the cup arms is broken.

6 WIND ALARM CONTROLLER INSTALLATION

6.1 Controller Location

To be effective the Wind Alarm controller must be in a location where one can view the display and hear

the alarm. At the same time it should not be accessible to unauthorized personnel. It will need to be

mounted near a 120VAC receptacle for power. If the controller is inside a building the sensor cable will

need to be routed outside so that the sensor can be exposed to the wind.

6.2 Controller Mounting

There are 4 knock-out locations inside the controller box for placing screws. It will be necessary to remove

the controller to access these points. After mounting the case to your wall or panel, use the provided caps

to cover the screw locations. This will help keep moisture from entering the box. Replace the controller

circuit board and secure it with the mounting screws.

Autres manuels pour 200-WS-01B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Novalynx Accessoires

Novalynx

Novalynx 200-WS-02E Manuel utilisateur

Novalynx

Novalynx 200-WS-02 Series Manuel utilisateur

Novalynx

Novalynx 260-2520 Manuel utilisateur

Novalynx

Novalynx 225-HMP60A Manuel utilisateur

Novalynx

Novalynx 200-WS-23-DP Manuel utilisateur

Novalynx

Novalynx 200-WS-01B Manuel utilisateur

Novalynx

Novalynx 200-WS-03D Manuel utilisateur

Novalynx

Novalynx 200-WS-22 Manuel utilisateur

Novalynx

Novalynx 200-WS-04 Manuel utilisateur

Novalynx

Novalynx 230-600C Manuel utilisateur

Novalynx

Novalynx 200-WS-02 Series Manuel utilisateur

Novalynx

Novalynx 200-WS-23 Manuel utilisateur

Novalynx

Novalynx 255-100 Manuel utilisateur

Novalynx

Novalynx 225-WS-32THA Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur