Nordson Rhino SD3 Guide de référence

RhinoSD3/XD3

Pneumatic Unloaders

Customer Product Manual

Part 1617021-01

Issued 04/20

NORDSON CORPORATION •AMHERST, OHIO •USA

For parts and technical support, call the Industrial Coating

Systems Customer Support Center at (800) 433-9319 or

contact your local Nordson representative.

This document is subject to change without notice.

Check http://emanuals.nordson.com for the latest version.

Part 1617021-01 E2020 Nordson Corporation

Nordson Corporation welcomes requests for information, comments, and

inquiries about its products. General information about Nordson can be

found on the Internet using the following address:

http://www.nordson.com.

Address all correspondence to:

Nordson Corporation

Attn: Customer Service

555 Jackson Street

Amherst, OH 44001

Notice

This is a Nordson Corporation publication which is protected by copyright.

Original copyright date 2020. No part of this document may be

photocopied, reproduced, or translated to another language without the

prior written consent of Nordson Corporation. The information contained

in this publication is subject to change without notice.

Trademarks

Rhino, Nordson, and the Nordson logo are registered trademarks of

Nordson Corporation.

All other trademarks are the property of their respective owners.

Table of Contents i

Part 1617021-01

E2020 Nordson Corporation

Table of Contents

Safety 1-1..................................................

Introduction 1-1.............................................

Qualified Personnel 1-1......................................

Intended Use 1-1...........................................

Regulations and Approvals 1-1...............................

Personal Safety 1-2.........................................

High-Pressure Fluids 1-2..................................

Fire Safety 1-3.............................................

Halogenated Hydrocarbon Solvent Hazards 1-4..............

Action in the Event of a Malfunction 1-4........................

Disposal 1-4...............................................

Safety Labels 1-5...........................................

Overview 2-1...............................................

Introduction 2-1.............................................

Specifications 2-1...........................................

Dimensions and Weight 2-1................................

Connections 2-2..........................................

Operating Sound Levels 2-2................................

Air Requirements 2-3......................................

Unloader Components 2-4....................................

55-Gallon Unloader 2-4...................................

5-Gallon Unloader 2-6.....................................

Hydraulic Section 2-8...................................

Pneumatic Control Module 2-9...........................

Follower Modules 2-10...................................

Interconnect Hose Module 2-11...........................

Hydraulic Section Pump Outlet Manifold 2-12................

Pneumatic Container Level Sensors 2-13...................

Bleeder or Ball Valve (System Configuration Dependant) 2-14.

Light Tower (System Configuration Dependant) 2-15..........

Conveyor (System Configuration Dependant) 2-16...........

Material Output Gauge

(System Configuration Dependant) 2-17....................

Pressure Relief Valve (System Configuration Dependant) 2-18.

Air Motor Pressure Relief Valve 2-19.......................

Follower Grid Plate (System Configuration Dependant) 2-20...

Container Hold-Down (System Configuration Dependant) 2-21.

Consumable Items 2-22.......................................

Adhesives, Sealants, and Lubricants 2-22.....................

Solvent Chamber Fluid 2-22.................................

Installation 3-1.............................................

Installation Procedure 3-1....................................

Unpack the Unloader 3-1...................................

Install the Unloader 3-2....................................

Table of Contents

Part 1617021-01 E2020 Nordson Corporation

Operation 4-1..............................................

First-Time Startup 4-1........................................

Container Change Procedure 4-5..............................

Pump Operation 4-8.........................................

Basic Operation 4-8.......................................

Pneumatic Controls 4-8....................................

Air Motor Supply 4-8......................................

Elevator and Blow-Off Air Supply 4-9........................

Maintenance 4-10............................................

Troubleshooting 5-1........................................

Parts and Repair 6-1........................................

Introduction 6-1.............................................

Unloader Modules 6-1.....................................

Reference Documentation 6-3..............................

55-Gallon Unloader 6-3..................................

5-Gallon Unloader 6-4...................................

Change Record i

Part 1617021-01

E2020 Nordson Corporation

Change Record

Revision Date Change

01 07/19 Initial release.

Change Record

Part 1617021-01 E2020 Nordson Corporation

Safety 1-1

Part 1617021-01

E2020 Nordson Corporation

Section 1

Safety

Introduction

Read and follow these safety instructions. Task- and equipment-specific

warnings, cautions, and instructions are included in equipment

documentation where appropriate.

Make sure all equipment documentation, including these instructions, is

accessible to persons operating or servicing equipment.

Qualified Personnel

Equipment owners are responsible for making sure that Nordson equipment

is installed, operated, and serviced by qualified personnel. Qualified

personnel are those employees or contractors who are trained to safely

perform their assigned tasks. They are familiar with all relevant safety rules

and regulations and are physically capable of performing their assigned

tasks.

Intended Use

Use of Nordson equipment in ways other than those described in the

documentation supplied with the equipment may result in injury to persons

or damage to property.

Some examples of unintended use of equipment include

Susing incompatible materials

Smaking unauthorized modifications

Sremoving or bypassing safety guards or interlocks

Susing incompatible or damaged parts

Susing unapproved auxiliary equipment

Soperating equipment in excess of maximum ratings

Regulations and Approvals

Make sure all equipment is rated and approved for the environment in which

it is used. Any approvals obtained for Nordson equipment will be voided if

instructions for installation, operation, and service are not followed.

Safety

1-2

Part 1617021-01 E2020 Nordson Corporation

Personal Safety

To prevent injury, follow these instructions.

SDo not operate or service equipment unless you are qualified.

SDo not operate equipment unless safety guards, doors, or covers are

intact and automatic interlocks are operating properly. Do not bypass or

disarm any safety devices.

SKeep clear of moving equipment. Before adjusting or servicing moving

equipment, shut off the power supply and wait until the equipment

comes to a complete stop. Lock out power and secure the equipment to

prevent unexpected movement.

SRelieve (bleed off) hydraulic and pneumatic pressure before adjusting or

servicing pressurized systems or components. Disconnect, lock out,

and tag switches before servicing electrical equipment.

SWhile operating manual spray guns, make sure you are grounded.

Wear electrically conductive gloves or a grounding strap connected to

the gun handle or other true earth ground. Do not wear or carry metallic

objects such as jewelry or tools.

SIf you receive even a slight electrical shock, shut down all electrical or

electrostatic equipment immediately. Do not restart the equipment until

the problem has been identified and corrected.

SObtain and read Safety Data Sheets (SDS) for all materials used.

Follow the manufacturer’s instructions for safe handling and use of

materials, and use recommended personal protection devices.

SMake sure the spray area is adequately ventilated.

STo prevent injury, be aware of less-obvious dangers in the workplace

that often cannot be completely eliminated, such as hot surfaces, sharp

edges, energized electrical circuits, and moving parts that cannot be

enclosed or otherwise guarded for practical reasons.

High-Pressure Fluids

High-pressure fluids, unless they are safely contained, are extremely

hazardous. Always relieve fluid pressure before adjusting or servicing high

pressure equipment. A jet of high-pressure fluid can cut like a knife and

cause serious bodily injury, amputation, or death. Fluids penetrating the

skin can also cause toxic poisoning.

If you suffer a fluid injection injury, seek medical care immediately. If

possible, provide a copy of the SDS for the injected fluid to the health care

provider.

Safety 1-3

Part 1617021-01

E2020 Nordson Corporation

The National Spray Equipment Manufacturers Association has created a

wallet card that you should carry when you are operating high-pressure

spray equipment. These cards are supplied with your equipment. The

following is the text of this card:

WARNING: Any injury caused by high pressure liquid can be serious. If

you are injured or even suspect an injury:

SGo to an emergency room immediately.

STell the doctor that you suspect an injection injury.

SShow them this card

STell them what kind of material you were spraying

MEDICAL ALERT—AIRLESS SPRAY WOUNDS: NOTE TO PHYSICIAN

Injection in the skin is a serious traumatic injury. It is important to treat the

injury surgically as soon as possible. Do not delay treatment to research

toxicity. Toxicity is a concern with some exotic coatings injected directly into

the bloodstream.

Consultation with a plastic surgeon or a reconstructive hand surgeon may

be advisable.

The seriousness of the wound depends on where the injury is on the body,

whether the substance hit something on its way in and deflected causing

more damage, and many other variables including skin microflora residing

in the paint or gun which are blasted into the wound. If the injected paint

contains acrylic latex and titanium dioxide that damage the tissue’s

resistance to infection, bacterial growth will flourish. The treatment that

doctors recommend for an injection injury to the hand includes immediate

decompression of the closed vascular compartments of the hand to release

the underlying tissue distended by the injected paint, judicious wound

debridement, and immediate antibiotic treatment.

Fire Safety

To avoid a fire or explosion, follow these instructions.

SGround all conductive equipment. Use only grounded air and fluid

hoses. Check equipment and workpiece grounding devices regularly.

Resistance to ground must not exceed one megohm.

SShut down all equipment immediately if you notice static sparking or

arcing. Do not restart the equipment until the cause has been identified

and corrected.

SDo not smoke, weld, grind, or use open flames where flammable

materials are being used or stored.

SDo not heat materials to temperatures above those recommended by

the manufacturer. Make sure heat monitoring and limiting devices are

working properly.

Safety

1-4

Part 1617021-01 E2020 Nordson Corporation

Fire Safety (contd)

SProvide adequate ventilation to prevent dangerous concentrations of

volatile particles or vapors. Refer to local codes or your material SDS

for guidance.

SDo not disconnect live electrical circuits when working with flammable

materials. Shut off power at a disconnect switch first to prevent

sparking.

SKnow where emergency stop buttons, shutoff valves, and fire

extinguishers are located. If a fire starts in a spray booth, immediately

shut off the spray system and exhaust fans.

SShut off electrostatic power and ground the charging system before

adjusting, cleaning, or repairing electrostatic equipment.

SClean, maintain, test, and repair equipment according to the instructions

in your equipment documentation.

SUse only replacement parts that are designed for use with original

equipment. Contact your Nordson representative for parts information

and advice.

Halogenated Hydrocarbon Solvent Hazards

Do not use halogenated hydrocarbon solvents in a pressurized system that

contains aluminum components. Under pressure, these solvents can react

with aluminum and explode, causing injury, death, or property damage.

Halogenated hydrocarbon solvents contain one or more of the following

elements:

Element Symbol Prefix

Fluorine F “Fluoro-”

Chlorine Cl “Chloro-”

Bromine Br “Bromo-”

Iodine I “Iodo-”

Check your material SDS or contact your material supplier for more

information. If you must use halogenated hydrocarbon solvents, contact

your Nordson representative for information about compatible Nordson

components.

Action in the Event of a Malfunction

If a system or any equipment in a system malfunctions, shut off the system

immediately and perform the following steps:

SDisconnect and lock out system electrical power. Close hydraulic and

pneumatic shutoff valves and relieve pressures.

SIdentify the reason for the malfunction and correct it before restarting the

system.

Disposal

Dispose of equipment and materials used in operation and servicing

according to local codes.

Autres manuels pour Rhino SD3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Nordson Pompe à eau

Nordson

Nordson PermaFlo 830 Guide de référence

Nordson

Nordson Rhino SD3 Guide de référence

Nordson

Nordson PermaFlo Series Guide de référence

Nordson

Nordson Rhino SD2 Guide de référence

Nordson

Nordson Prodigy Generation II Manuel utilisateur

Nordson

Nordson Rhino XD2 Manuel utilisateur

Nordson

Nordson PermaFlo 815 Manuel utilisateur

Nordson

Nordson 100 PLUS FB Manuel utilisateur

Nordson

Nordson 1604629 Manuel utilisateur

Nordson

Nordson BM 200 Manuel de la liste des pièces

Nordson

Nordson 32 Manuel utilisateur

Nordson

Nordson VDK-MIDI TYPE 6 Manuel utilisateur

Nordson

Nordson Rhino SD Manuel utilisateur

Nordson

Nordson cp Manuel utilisateur

Nordson

Nordson StediFlo 57:1 Guide de référence

Nordson

Nordson Spectrum VT Feed Center Manuel utilisateur

Nordson

Nordson HD+ Manuel utilisateur

Nordson

Nordson Rhino XD2 Manuel utilisateur

Nordson

Nordson Prodigy HDLV Manuel utilisateur

Nordson

Nordson High Flow FB Manuel utilisateur

Nordson

Nordson 2300 Manuel utilisateur

Nordson

Nordson Tribomatic 635598 Manuel utilisateur

Nordson

Nordson EP2 Manuel utilisateur

Nordson

Nordson 25B Guide de référence

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur