Nordson EFD ValveMate 8040 Manuel utilisateur

Quick Start Guide

ValveMate™8040

USA & Canada: 800.556.3484 or +1.401.431.7000

Europe: 0800 585733 or +44 (0) 1582 666334

Asia: +86 (21) 5854 2345

[email protected] www.nordsonefd.com

Electronic pdf files of Nordson EFD manuals are also

available at www.nordsonefd.com

Unpack the ValveMate 8040.

This is also a good time to activate the

one-year warranty. Register online at

www.nordsonefd.com/warranty/valves/one.

Mount the VM8040 and input power supply. The

ValveMate can be mounted either over or under a

cabinet or panel mounted using the bezel mount

(included).

Install and connect the power supply.

Connect the power supply cord to

the ValveMate input connector.

Secure with locking ring.

Install the air pressure regulator and air solenoids.

A. Connect the plant air supply to the inlet of

the filter regulator.

B. Connect the solenoid cable between the

solenoid and VM8040.

Connect the low air pressure sensor and tank

low level switches (if low level float provided

with reservoir) to ALARM IN. *See note below.

Connect the initiate I/O to the host machine control

circuitry or to the bench initiate switch.

Install the spray valves.

A. Mount the valves using

appropriate mounting

hardware.

B. Connect the valve control air hoses

to the appropriate solenoid outlets.

Connect the fluid reservoir.

A. Connect the fluid reservoir air pressure

regulator to the plant air supply using the air

hose and fitting supplied.

B. Connect the reservoir fluid lines to the valves.

Fill the fluid reservoir and secure the cover.

Locking ring

To plant air

Spring clamps

Panel mount bezel

*Note: Wire additional normally closed alarm sensors in series and connect to the ALARM

IN +/- terminals. If no alarm switch is used, the ALARM IN +/- terminals must

have a jumper installed to disable the ALARM feature.

Set the tank pressure to 5 psi (0.35 bar) for low

viscosity fluids and 15 psi (1.03 bar) for medium

viscosity fluids.

Set the spray valve stroke adjustment to 1/2 turn

open. This is a starting point only.

Place a container under the spray valve(s).

A. Using the MODE button, place the

VM8040 in mode.

B. Press the button and hold until

fluid flows and fluid lines are free of air. Then

set the flow rate using the valve stroke setting

and tank air pressure. Avoid high tank

pressures with low stroke settings.

C. Set the flow rate by counting drops to about

one per second as a starting point.

Adjusting the spray

A. Set the nozzle air pressure regulator to 10 psi.

B. Press the button and observe the

spray pattern.

C. Using the spray valve stroke adjustment and

tank air pressure, increase or decrease settings

to arrive at the desired spray pattern.

D. Using the MODE button, place the

controller into the mode.

E. Press the SEL button repeatedly until all

valve indicator lights are lit.

F. Enter a spray time of .050 seconds by pressing

the up or down arrow next to the LED screen.

G. With the container still under the valves, press

the CYCLE button to test the deposit

amount.

H. Increase or decrease the valve open time to

arrive at the correct deposit size. To equalize

all valves, press the SEL button to

highlight individual valves and use the valve

open time to equalize the output.

Final check list

A. Air pressure to solenoid pack is set to 80 psi (5.5 bar).

B. For spray valves, nozzle air regulator is set to 0 psi (0 bar).

C. Solenoids and I/O are wired correctly.

D. Valves and fluid reservoir are properly connected.

E. Power to the ValveMate is on, and indicator lamps and LED are lit.

Valve open time is the primary control of deposit size. It is

normal to end with different time settings for each valve.

TIP

Autres manuels pour ValveMate 8040

Autres manuels Nordson EFD Contrôleurs

Nordson EFD

Nordson EFD ValveMate 7140 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 8040 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 8000 Manuel utilisateur

Nordson EFD

Nordson EFD ProcessMate T10 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 9000 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 8040 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7140 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 9000 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7197PCP Manuel utilisateur

Nordson EFD

Nordson EFD PICO Controller 2+2 CH-V2 Series Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7100 Manuel utilisateur

Nordson EFD

Nordson EFD Liquidyn V10D Manuel utilisateur

Nordson EFD

Nordson EFD PICO Touch Series Manuel utilisateur

Nordson EFD

Nordson EFD V3 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 8040 Manuel utilisateur

Nordson EFD

Nordson EFD PICO Touch Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7140 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7100 Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7160RA Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7197PCP Manuel utilisateur

Nordson EFD

Nordson EFD ValveMate 7194 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur