Norco BIS-6540HD Manuel utilisateur
BIS-6540HD
Full HD Compact Signage Platform
USER' Manual V1.0
Shenzhen NORCO Intelligent Technology Co., Ltd.:0755-27331166
Beijing：010-82671166
Shanghai：021-61212088
Nanjing: 025-58015489
Chengdu：028-85259319
Shenyang：024-23960846
Xi’an：029-88338386
Nanjing: 025-58015489
Wuhan：027-87858983
Tianjin：022-23727100
Singapore：65-68530809
Netherlands：31-040-2668554
Web：www.norco.cn
BIS-6540HD
Full HD Compact Signage Platform
USER' Manual V1.0
Place/Data: HONG KONG/2009
Shenzhen NORCO Intelligent Technology Co.,Ltd.
Shenzhen NORCO Intelligent Technology Co.,Ltd.
BIS-6540HD Full HD Compact Signage Platform
Data: 2009
Trade Name：Shenzhen NORCO Intelligent Technology Co.,Ltd.
Model Name：BIS-6540HD
Responsible Party：Shenzhen NORCO Intelligent Technology Co.,Ltd.
Equipment Classification：FCC Class B Subassembly
TypeofProduct：BIS-6540HD Full HD Compact Signage Platform
Manufacturer：Shenzhen NORCO Intelligent Technology Co.,Ltd.
Copyright
With the exception of showing the accessories of product configuration,
this manual do not create any commitment of our company. We retained the
rights to change it without prior notice. We will not be responsible for any
installation, the result of improper use of direct, indirect, intentional or
unintentional damage or hidden dangers.
Before buying products, please learn about product performance from
the seller to see if it is in line with your needs. NORCO is a registered
trademark of Shenzhen NORCO Intelligent Technology CO.,Ltd. Other
trademarks involved in this manual, their ownership are owned by its
respective owners. The contents of this manual are protected by copyright
law. All rights are strictly reserved. Any form of unauthorized reproduction
including but not limited to carbon copy, facsimile transmission and
electronic copy or email should be destroyed immediately.
Safety Instructions
1：Please read these safety instructions carefully。
2：Before inserting or removing expansion cards, re-assembling or
re-configuring, disconnect the computer and peripherals from their power
sources to prevent electric shock or system board damage。
3：Before attempting to move the product, the system must be
powered-down and the power cord must be disconnected from the power
source。
4：Before connecting or disconnecting any signal line, first turn off all power
resources and disconnect the power cord from power source。
5：To help avoid possible damage to system boards, wait at least 30
seconds after turning off the computer before re-turning on the computer。
6：Use cross head screwdriver to operate. A magnetic screwdriver is
recommended (magnet to collect screws).Do not leave any tools or
components inside the chassis.
7：Assure abundant cooling and streamline ventilation。
8：If anything unexpected exists during Equipment used, please contact the
professionals.
Contents
Chapter General Information....................................................................................... 1
1.1 Introduction ................................................................................................................. 1
1.2 Features...................................................................................................................... 1
1.3 Hardware Specification............................................................................................... 2
1.4 Dimensions Diagram .................................................................................................. 4
Chapter2 Hardware Functionality.............................................................................. 5
2.1 External I/O Connectors ............................................................................................. 5
2.2 Internal Structure ........................................................................................................ 6
2.3 Back Panel I/O Connectors ........................................................................................ 7
2.3.1 Serial Port（COM1,COM2）................................................................................... 7
2.3.2 USB Port（USB）................................................................................................... 7
2.3.3 Ethernet connector（LAN）.................................................................................... 8
2.3.4 PS2 Keyboard/Mouse Connector（MS，KB）....................................................... 9
2.3.5 Audio Jack（LINE-OUT，MIC-IN）........................................................................ 9
2.3.6 VGA Connector（VGA）....................................................................................... 10
2.3.7 DVI Connector（DVI）.......................................................................................... 10
2.3.8 Power input connector（POWER）...................................................................... 11
2.4 Inside connectors...................................................................................................... 12
2.4.1 IDE Connector（IDE1）........................................................................................ 12
2.4.2 SATA Connector&SATA Power Connector（SATA0，SATA1，S_PWR）............ 13
2.4.3 Parallel Por（LPT）.............................................................................................. 15
2.4.4 Onboard USB Ports（USB12，USB34，USB56）.............................................. 16
2.4.5 Expandsion Serial Ports（COM3-6，COM7-10）................................................ 17
2.4.6 IRDA interface（IRDA）........................................................................................ 19
2.4.7 GPIO（J10）......................................................................................................... 19
2.4.8 ATX PowerSupply Connector（ATX）................................................................... 21
2.4.9 Front Panel connector（J4）................................................................................ 22
Chapter3 Hardware Installation................................................................................ 24
3.1 Setting Jumpers........................................................................................................ 24
3.1.1 Clear CMOS（JCC）............................................................................................ 24
3.1.2 COM2 setting（J5，J6，J7）............................................................................... 25
3.1.3 CF Card Master/Slave Selection（JCF）.............................................................. 27
3.2 Installing the DDR SDRAM Memory Module ............................................................ 27
3.3 Installing the 2.5" Hard Disk Drive (HDD) ................................................................. 28
3.4 CF Card Installation .................................................................................................. 29
3.5 Installing Wall-Mount ................................................................................................ 30
3.6 Connecting Power .................................................................................................... 30
Chapter4 BIOS Setup..................................................................................................... 29
4.1 Standard CMOS Setup ............................................................................................. 30
4.2 Advanced BIOS Features ......................................................................................... 33
4.2.1 CPU Feature.......................................................................................................... 33
4.2.2 Removable Device Priority .................................................................................... 35
4.2.3 Hard Disk Boot Priority .......................................................................................... 35
4.2.4 CD-ROM Boot Priority ........................................................................................... 36
4.3 Advanced Chipset Features...................................................................................... 39
4.4 Integrated peripherals............................................................................................... 42
4.4.1 OnChip IDE Device................................................................................................ 43
4.4.2 Onboard Device..................................................................................................... 44
4.4.3 Super IO Device .................................................................................................... 45
4.4.4 F81216D[COM3-COM10] ...................................................................................... 48
4.4.5 USB Device Setting ............................................................................................... 50
4.5 Power Management Setup ....................................................................................... 51
4.6 PnP/PCI Configurations............................................................................................ 54
4.7 PC Health Status ...................................................................................................... 55
4.8 Frequency/Voltage Control ....................................................................................... 57
4.9 Load Fail-Safe Defaults ............................................................................................ 57
4.10 Load Optimized Defaults ........................................................................................ 58
4.11 Set Supervisor Password........................................................................................ 59
4.12 Set User Password ................................................................................................. 59
4.13 Save&Exit Setup..................................................................................................... 60
4.14 Exit Without Saving................................................................................................. 61
Appendix.............................................................................................................................. 63
Appendix 1: Driver Installation ........................................................................................ 63
Appendix 2：Watchdog programmer guide.................................................................... 64
Appendix3：GPIO Instruction......................................................................................... 66
Appendix 4: Glossary...................................................................................................... 67
Packing List
Thank you very much for choosing our products. Please check your
package completely as the following item checklist first, if you find any
components lost or damaged, please contact your retailer.
■BIS-6540HD
■User’s Manual
■Drive Disk
■Power cord
■Power adapter
■Wall-Mount
■Screw
1pcs
1pcs
1pcs
1pcs
1set
1set
9pcs
Table des matières
Autres manuels Norco Ordinateur de bureau
Norco
Norco BIS-6660C Manuel utilisateur
Norco
Norco BIS-1280 Manuel utilisateur
Norco
Norco BIS-6680H Manuel utilisateur
Norco
Norco BIS-1280A40 Manuel utilisateur
Norco
Norco EMB-3531 Manuel utilisateur
Norco
Norco BIS-6620 Manuel utilisateur
Norco
Norco EMB-7570 Manuel utilisateur
Norco
Norco BIS-6622 II Manuel utilisateur
Norco
Norco BIS-6620 Manuel utilisateur
Norco
Norco EMB-7535 Manuel utilisateur
