Nomadic Display HangTen Manuel

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Setup Instructions

HangTen

CONGRATULATIONS!

Like thousands of Nomadic Display owners around the world, you now own the

highest quality portable/modular display. Your Nomadic HangTen is specially

designed to give you the ultimate in versatility. Original, Classic (curved) and Plus

(straight) frame systems integrate to meet your growing exhibit demands. And your

100% satisfaction is guaranteed by Nomadic.

The Lifetime Warranty

Your HangTen frame is guaranteed for life. If it ever fails to

function Nomadic Display will repair it free of charge for as long

as you own it. Be sure to complete and return the enclosed

warranty card immediately.

Made by Nomadic Display

Superior in design and strength, your Nomadic Display is built in Nomadic’s own

manufacturing plants in the U.S. and Ireland. We use only premium grade materials

and take pride in maintaining the highest standards of craftsmanship. Your display

is delivered to you packed for maximum protection and quick assembly.

Nomadic Cares, Please Recycle

All Nomadic aluminum frames and cases can be recycled.

We recommend that you assemble and repack your display

prior to your ﬁrst event. It is important to follow each step in

the order indicated. If you need additional assistance or have

any questions, please call your nearest Nomadic LifeLine:

North America: Ireland/Europe:

800.732.9395 + 353.1.208.7261

United Kingdom:

07699 734215

TABLE OF CONTENTS

Frames

oFrame Setup ...................................................................... 2

Graphics

oGraphic & Light Setup ........................................................ 3

Accessories

oHeader Setup...................................................................... 4

oProduct Pedestal ................................................................ 5

oSmall Monitor & Keyboard Shelf Setup .............................. 6

oMedium Monitor Setup....................................................... 7

oLarge Monitor Setup........................................................... 8

oFin Setup, Original .............................................................. 9

oFin Setup, Classic/Plus ...................................................... 10

oVertical Proﬁle Setup .......................................................... 11

oStand-alone Counter Setup................................................ 12

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Connect top H1/H2 extrusion to top V1 and

V2 extrusions (track on top). Lock with hex

wrench.

Lift frame by support extrusion and walk it

back into an upright position.

Connect bottom H1/H2 extrusion to

bottom V1 and V2 extrusions (track on

bottom). Lock with hex wrench.

Your Original frame is now ready for

graphics.

Slide monitor extrusion into place. Lock with hex wrench at the top and

bottom.

Your Plus frame is now ready for

graphics.

Your Classic frame is now ready for

graphics.

Frame Setup Instructions

Place extrusions with locking hole facing

up and connect.

Monitor top to Monitor bottom

Top V1 to Bottom V1 / Top V2 to Bottom V2

Bottom H1 to Bottom H2 / Top H1 to Top H2*

Top H1 to Top H2*

If you have a header, slide H channel

above track. Lock tightly with hex wrench

provided.

Place foot upright on ﬂoor. Insert V1

extrusion into foot channel with locking

holes facing inward. Lock with hex

wrench. Repeat with V2 extrusion.

HangTen

Remove HangTen parts from black bag

and lay them out label side up. You will

build the frame on the ground facing

down.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Frames • 2

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Tuck the graphic edge from center out to

left and right corners along the top and

then bottom track.

Lights are connected to holes on the

top of your frame.

Fold excess corner fabric under and

press edge of fabric graphic onto

Velcro® on one side. Work your way

down the side of the frame.

Insert the peg base of the lights into a

hole on the top part of the frame.

Pull taut as you press edge of fabric

graphic onto Velcro®. Work your way

down the side of the frame. Repeat on

other side.

Your assembled HangTen display is now

ready for accessories.

Swivel ﬁxture to adjust position.

Graphic & Light Setup Instructions

Lift assembled frame into upright

position. Insert top corners of fabric

graphic plastic edge into the horizontal

track along the top H1/H2 extrusions.

Tuck the plastic edge into the horizontal

groove about 3” to secure the top two

corners.

Insert lower corners of fabric graphic into

the horizontal track along the bottom

H1/H2 extrusion. Tuck the plastic edge

into the horizontal groove about 3” to

secure bottom two corners.

HangTen

Follow steps on the “Frame Setup

Instructions”. Alwas use white cotton

gloves provided when handling fabric

graphics to prevent soiling.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Graphics • 3

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Insert standoffs into the header horizontal

bars about 1 1/2” from each edge. Turn

clockwise to tighten.

Guide holes in header graphic onto

standoffs.

Fasten front side with two standoff caps. Your header assembly is complete.

Header Setup Instructions

Follow steps on the “Graphic & Light

Instructions”.

Lay out header parts. Attach Header1/Header2 horizontal

bars to either side of the H channel.

Tighten with hex wrench provided.

HangTen

Follow steps on the “Frame Setup

Instructions”. Remember to slide the

“H” channel above the track.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Accessories • 4

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Guide pedestal top underside onto

extrusion. Once, aligned push down

to engage it.

Align groove on the rear of the graphic

with the extrusion.

Tighten underside with hex wrench

provided.

Insert the top brass connector into the

groove. Tighten standoff cap to lock

brass connector into the extrusion.

Repeat on bottom of graphic.

Loosely attach standoff cap to a brass

connector on either side of the top hole

in the graphic.

Brass connector should be on the rear

of the panel. Repeat on bottom hole of

graphic.

Your product pedestal assembly is

complete.

Product Pedestal Setup Instructions

Follow steps on the “Graphic & Light

Instructions”.

Lay out pedestal parts. Tap insert out of foot from underside.

Slide extrusion into front slot with

channel facing outward. Tighten inside

lock hole with hex wrench provided.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.

Accessories • 5

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Tighten with hex wrench provided.

Slide keyboard arm into channel on the

underside of the shelf.

Attach monitor plate to cam lock and

tighten with hex wrench provided.

Lock keyboard arm into place on both

sides of channel. Tighten with hex wrench

provided.

Bolt bracket to rear of monitor. Lift monitor into position by sliding

vertical connector onto rectangular

framework until it clicks into the spring,

with wider side on the top.

Your small monitor mount and keyboard

shelf assembly are complete.

Guide keyboard arm through slot in

front of graphic panel into the extru-

sion behind it. Tighten with hex wrench

provided.

Up to 22” Small Monitor/Keyboard Shelf Setup Instructions

Follow steps on the “Graphic & Light

Instructions”.

Lay out monitor and keyboard parts. Guide cam lock through slot in front of

graphic panel into the extrusion

behind it.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Accessories • 6

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Follow steps on the “Graphic & Light

Instructions”. Four bracket corners should

align with holes in graphic.

Your assembled medium monitor mount

should look like this without the monitor

or graphic attached.

Attach metal frame to black mount.

Secure 4 outside points through slots in

graphic panel with washers and tighten

wingnuts.

Bolt two rails to rear of monitor. Lift monitor into position by sliding the

vertical bars on the back of the monitor

onto the monitor bracket.

23”-37” Medium Monitor Mount Setup Instructions

Lay out medium monitor mount parts. Insert the 1” standoffs into the monitor

extrusion. Slide the standoffs so they

are spaced apart to accomodate the

monitor mount.

Place black monitor mount over the

standoffs and tighten wingnuts.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Accessories • 7

Revised: 03/05/12 North America: 800.732.9395 Europe: +353.98.66011

Guide cam lock through slot in front of

graphic panel into the vertical extrusion

behind the graphic.

Tighten both sides with allen wrench

provided.

Insert horizontal extrusion to rear of

monitor top extrusion in the desired

position and tighten locks. Tighten with

allen wrench provided.

Bolt two vertical rails to rear of monitor.

Repeat 2nd horizontal attachment to

2nd vertical extrusion. Tighten with allen

wrench provided.

Connect monitor bracket to the cam

lock.

Your assembled large monitor mount

should look like this without the monitor

or graphic attached.

Lift monitor into position by sliding

vertical rails onto the monitor bracket.

38”-46” Large Monitor Mount Setup Instructions

Slide 2nd monitor extrusion into place and

lock at top and bottom with hex wrench

provided.

Follow steps on the “Graphic & Light

Instructions”.

Lay out large monitor parts.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with Allen Wrench always give it a 3/4 turn clockwise until tight.

Accessories • 8

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Fins attach to rear of frame. Insert the

loosened brass connectors into the

extrusion channel at the back of the

display.

Tighten standoff caps. Make sure the

brass connector is locked before letting

go of the graphic ﬁn.

Your Origninal ﬁn assembly is complete.

Original Fin Setup Instructions

Follow steps on the “Graphic & Light

Instructions”.

Lay out pieces on the ground. Insert brass ﬁtting loosely onto rigid

graphic panel at the top and bottom

with cap.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.

Accessories • 9

Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011

Guide ﬁn into the edge mount standoff. Hold the ﬁn and tighten edge mount

standoff with hex wrench provided.

Repeat process with bottom ﬁn.

Your Classic/Plus ﬁn assembly is

complete.

Classic/Plus Fin Setup Instructions

Follow steps on the “Graphic & Light

Instructions”.

Lay out ﬁn parts. Fins attach to sides of Classic/Plus

frame. Insert edge mount standoffs in

holes on the side of frame. Tighten with

hex wrench provided.

HangTen

Follow steps on the “Frame Setup

Instructions”.

Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.

Accessories • 10

Table des matières

Autres manuels Nomadic Display Moniteur

Nomadic Display

Nomadic Display SPLUS-SP31 Manuel

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation