Nokia BH-217 Manuel utilisateur

Nokia Bluetooth Headset BH-217

Issue 1.0

DECLARATION OF CONFORMITY

Hereby, NOKIA CORPORATION declares

that this BH-217 product is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/

EC. A copy of the Declaration of

Conformity can be found at http://

www.nokia.com/phones/

declaration_of_conformity/.

Bluetooth is a registered trademark of

Bluetooth SIG, Inc.

Introduction

With the Nokia Bluetooth Headset

BH-217, you can make and answer

calls hands-free with your

compatible mobile device.

Read this user guide carefully before

using the headset. Also, read the

user guide for the device that you

connect to the headset.

Warning: The connector of

the clip and car cradle may

contain a small amount of

nickel. Persons who are

sensitised to nickel may

have symptoms from prolonged skin

contact with the connector.

Bluetooth compatibility

The headset is compliant with the

Bluetooth Specification 2.1 + EDR

supporting the Headset Profile 1.1

and Hands-Free Profile 1.5. Check

with the manufacturers of other

devices to determine their

compatibility with this device.

Get started

The headset contains the following

parts shown on the title page:

multifunction key (1), earloop (2),

indicator light (3), earpiece (4),

microphone (5), and charger

connector (6).

Before using the headset, you must

charge the battery and pair the

headset with a compatible device.

Compatible chargers

This device is intended for use when

supplied with power from the

following chargers: AC-3, AC-4, AC-

5, AC-8, DC-4 and DC-9. The exact

charger model number may vary

depending on the type of plug. The

plug variant is identified by one of

the following: E, X, AR, U, A, C, K, or

Charge the battery

1. Connect the charger to a wall

outlet.

2. Connect the charger cable to the

charger connector.

To charge the headset when it is

in the clip or car cradle, insert

the lower end of the headset into

the clip or car cradle (12), and

connect the charger cable to the

charger connector on the clip or

cradle (13).

The red indicator light is

displayed during charging.

Charging the battery fully may

take up to 2 hours.

3. When the battery is fully

charged, the green indicator

light is displayed. Disconnect the

charger from the headset (or

from the clip or car cradle), then

from the wall outlet.

The fully charged battery has power

for up to 5 hours of talk time. When

you keep the headset in the clip or

car cradle, the fully charged battery

has power for up to 3 months of

standby time. When you use the

headset without the clip or cradle,

the standby time is up to 100 hours.

To check the battery charge when

the headset is not connected to a

charger, press the multifunction key

when the headset is connected to a

mobile device. If the indicator light

is green, the charge level is

sufficient. If the light is yellow, you

may need to recharge the battery

soon. If the light is red, recharge the

battery.

When the battery charge is low, the

headset beeps every 5 minutes, the

red indicator light flashes, and if

voice prompts are activated, there is

an audible notification. If voice

prompts are activated, there is also

an audible notification when the

battery is completely discharged.

Switch the headset on

Remove the headset from the clip or

car cradle. If the headset is not in

the clip or cradle, press the

multifunction key. The headset

beeps, and the green indicator light

flashes slowly while the headset

tries to connect to the last or two

last connected devices.

When the headset is connected to

at least one device and is ready for

use, the blue indicator light flashes

slowly. If the headset has not been

paired with a device, it

automatically enters pairing mode.

Switch the headset off

Place the headset into the clip or car

cradle, or press and hold the

multifunction key for about 5

seconds. The headset beeps, and the

red indicator light is briefly

displayed.

If the headset is not connected to a

device within about 30 minutes, it

switches off automatically.

Pair and connect the headset

Before using the headset, you must

pair and connect it to a compatible

device.

You can pair the headset with up to

eight devices, but you can connect

it to a maximum of two devices at a

time.

To pair and connect the headset to a

device:

1. Make sure your mobile device is

switched on and the headset is

off.

2. If the headset has not been

previously paired with a device,

switch on the headset. The

headset enters pairing mode, and

the blue indicator light starts to

flash quickly.

If the headset has been

previously paired with a device,

make sure the headset is

switched off and not placed in

the clip or car cradle, and press

and hold the multifunction key

for about 5 seconds until the

blue indicator light starts to

flash quickly.

3. Within about 3 minutes, activate

Bluetooth on your device, and

set it to search for Bluetooth

devices. For details, see the user

guide of your mobile device.

4. Select the headset from the list

of found devices.

5. If necessary, enter the passcode

0000 to pair and connect the

headset to your device.

In some devices, you may need to

make the connection separately

after pairing.

When the headset is connected to

at least one device and is ready for

use, the blue indicator light flashes

slowly.

To manually connect the headset to

the last used device, press and hold

the multifunction key for about 2

seconds (when no other device is

connected), or make the connection

in the Bluetooth menu of the device.

You may be able to set your device

so that the headset connects to it

automatically. To activate this

feature in a Nokia device, modify

the paired device settings in the

Bluetooth menu.

Basic use

Change the earpad

The headset may be provided with

different sized earpads. Select the

earpad that fits the best and is the

most comfortable for your ear.

To change the earpad, pull the

current earpad from the earpiece,

and push the new earpad into place

(7).

Place the headset on the ear

To use the headset with the earloop,

attach the earloop to it (11). To

detach the earloop, gently pull it

from the headset.

You can rotate the earpad to keep

the headset securely in the ear (8).

For example, if you use the headset

on the right ear, you may need to

rotate the earpad to the right for

the best fit. If you wear an earring,

make sure it is not accidentally

attached to the earpad.

To place the headset on the ear,

slide the earloop behind your ear (9),

and gently push the earpiece

against your ear. Point the headset

towards your mouth (10).

Store in the clip or car cradle

When you do not keep the headset

on your ear, store it in the clip or car

cradle. When the headset is in the

clip or cradle, it is switched off.

When you remove the headset from

the clip or cradle, the headset

automatically switches on.

To place the headset into the clip or

cradle, slide the headset into place

(14). To remove the headset, slide it

out.

Install the car cradle

When you install the cradle in a car,

make sure it does not interfere with

or hinder the steering or braking

systems or other systems used in the

operation of the vehicle (for

example, airbags) or disturb your

field of vision while driving. Check

that the deployment of the airbag is

not blocked or impaired in any way.

To install the car cradle, peel off the

protective sheet from the cradle,

and press the cradle against a flat

surface so that it stays firmly in

place. Do not install the cradle in a

place where you might come in

contact with it in the event of an

accident or collision.

Use the car cradle

When you use the headset with the

cradle in a car, obey all local laws.

Always keep your hands free to

operate the vehicle while driving.

Your first consideration while

driving should be road safety. Only

operate the headset or car cradle if

it is safe to do so under all driving

conditions.

Periodically check that the adhesive

at the bottom of the car cradle is

firmly attached, especially if the

ambient temperature changes a lot.

It is recommended that you do not

leave the car cradle inside the

vehicle in direct sunlight or in

excessive heat.

Adjust volume

The headset automatically adjusts

the volume according to ambient

noise. To manually adjust the

volume, use the volume controls of

the connected device.

The selected volume level is saved

for the device that is currently

connected to the headset.

Calls

To make a call, use your mobile

device in the normal way when the

headset is connected to it.

To redial the number you last called

(if your mobile device supports this

feature with the headset), when no

call is in progress, press the

multifunction key twice when the

headset is not in the clip or car

cradle.

To activate voice dialling (if your

mobile device supports this feature

with the headset), when no call is in

progress, press and hold the

multifunction key for about 2

seconds when the headset is not in

the clip or cradle. Proceed as

described in the user guide of the

mobile device.

To answer a call, remove the

headset from the clip or cradle. If

the headset is not in the clip or

cradle, press the multifunction key.

To reject a call, press the

multifunction key twice, or place

the headset into the clip or cradle.

To end a call, place the headset into

the clip or cradle, or press the

multifunction key when the headset

is not in the clip or cradle.

To switch a call between the

headset and a compatible

connected device, press and hold

the multifunction key for about 2

seconds.

Connect to two devices

The headset can be connected to

two devices at the same time.

Pair and connect to two devices

To pair the headset with two

devices, switch on the headset,

activate pairing mode, and pair it

with the first device. Switch off the

headset, activate pairing mode, and

pair it with the second device.

To connect the headset to the two

devices, switch the headset off and

back on.

Handle calls

If the headset can connect to two

devices at the same time and you

use redialling or voice dialling, the

call is made on the device that you

last used to make a call when the

headset was connected to it.

To answer a call on one connected

device and end the active call on the

other device, press the

multifunction key.

Autres manuels pour BH-217

Table des matières

Autres manuels Nokia casque

Nokia

Nokia Bluetooth Headset BH-701 Manuel utilisateur

Nokia

Nokia BH-106 Black Manuel utilisateur

Nokia

Nokia Hs-45 - And Ad-57 Xpressmusic Stereo Headset 5310 3.5mm... Manuel utilisateur

Nokia

Nokia HS 36W Manuel utilisateur

Nokia

Nokia BH 604 - Headset - Binaural Manuel utilisateur

Nokia

Nokia Luna Manuel utilisateur

Nokia

Nokia N-GAGE Manuel utilisateur

Nokia

Nokia Comm Band + CB-201 Manuel utilisateur

Nokia

Nokia BH-118 Manuel utilisateur

Nokia

Nokia BH-101 Manuel utilisateur

Nokia

Nokia BH 202 - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia BH-304 Manuel utilisateur

Nokia

Nokia BH-803 - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia BH-302 Manuel utilisateur

Nokia

Nokia BH 103 - Headset - In-ear ear-bud Manuel utilisateur

Nokia

Nokia BH-607 Manuel utilisateur

Nokia

Nokia BH-940 Manuel utilisateur

Nokia

Nokia BH-905I Manuel utilisateur

Nokia

Nokia BH 212 - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia BH105 - Bluetooth Headset Ice Manuel utilisateur

Nokia

Nokia BH-106 Black Manuel utilisateur

Nokia

Nokia HS-29 Manuel utilisateur

Nokia

Nokia BH-200 Manuel utilisateur

Nokia

Nokia BH-902 Manuel utilisateur

Manuels casque populaires d'autres marques

Sena

Sena SMH10 Manuel utilisateur

IASUS

IASUS Stealth IA-NT4-BASIC-BT Manuel utilisateur

Sennheiser

Sennheiser EPOS ADAPT 230 Manuel utilisateur

Doro

Doro Flexus HS2005 Manuel utilisateur

GE 98971 Manuel utilisateur

Hama

Hama 00184070 Manuel utilisateur

Plantronics

Plantronics Blackwire 3200 Series Manuel utilisateur

Blue Tiger

Blue Tiger Advantage PLUS Manuel utilisateur

Jawbone

Jawbone Icon Manuel utilisateur

Jabra

Jabra FR 20 Manuel utilisateur

Roxcore

Roxcore Flow A+ Manuel utilisateur

Turtle Beach

Turtle Beach XP 510 Manuel utilisateur

Philips

Philips SHB6101 Manuel utilisateur

Jabra

Jabra PRO 9460 Duo Manuel utilisateur

HyperX

HyperX HyperX Cloud Flight Manuel utilisateur

Bose

Bose MIE2 Mobile Manuel utilisateur

Jabra

Jabra Steel Manuel utilisateur

HyperX

HyperX cloud ii Manuel utilisateur