NoiseKen LSS-6000 Series Manuel utilisateur

INSTRUCTION MANUAL

INJECTIONUNIT

ForLIGHTENINGSURGESIMULATOTR

LSS-6000SERIES

MODEL:LSS-INJ6400SIG

NOISELABORATORYCO.,LTD. 2.01Edition

AEE00146-00E-1B

NOTICE

The contents of this booklet are subject to change without prior notice.

No part of this booklet may be reproduced or transferred, in any form, for any purpose,

without the permission of Noise Laboratory Co., Ltd.

The contents of this booklet have been thoroughly checked. However, if a doubtful point,

an error in writing or a missing is found, please contact us.

Noise Laboratory Co., Ltd. shall have no liability for any trouble resulting from the

misuse or improper handling of this product regardless of the contents of this booklet or

arising from the repair or remodeling of this product by a third party other than Noise

Laboratory Co., Ltd. or its authorized person.

Noise Laboratory Co., Ltd. shall have no liability for any trouble resulting from the

remodeling or modification of this product.

In no event shall Noise Laboratory Co., Ltd. be liable for any results arising from the use

of this produc

IMPORTANT SAFETY PRECAUTIONS

The following is very important matters in order to safely handle this product (called the unit

hereafter). Read carefully and strictly observe them.

1. As the unit outputs high voltage (6600V maximum) and great current

(157A maximum) by surge from LSS-6000 series, carefully handle it.

Mishandlingorcarelessoperationmayresultin a fatalwound.

2. Use of the unit and the lightning surge simulator (LSS-6000 series) unit

in an explosive area such as "No fire" area etc. is prohibited. If used in

such an area, it is liable to cause combustion or ignition due to

discharge.

3. Any person who has an implanted pacemaker in the body should not

operate this unit. Furthermore, such a person should not enter the test

area while this unit is operating.

4. Test equipment to be used with this unit should be capable of insulating against

at least a voltage of 6600V. The equipment under test (called EUT hereafter)

using this unit should be performed in a protective enclosure or cover against

scatteringbroken pieces, fireelectricshock,etc.

5. When connecting this unit to accessories for test waveforms and test conditions,

optional equipment and other equipment, press STOP button of the lightening

surge simulator (LSS-6000 series) and check that lamp of STOP button is lighting

up beforehand. Otherwise, you may receive an electric shock. There may be

residual voltage even if the test is stopped. Therefore, start operation after a lapse

ofmorethan 3seconds.

<LSS-6000Series >

LSS-6010,LSS-6110:CombinationWaveGenerator

LSS-6030, LSS-6130: Combination Wave, 10/700µs Surge, 0.5µs/100kHz Ring

Wave Generator

Memorandum

2.APPLICATION FORM FOR INSTRUCTION MANUAL

Weplaceanorderforaninstructionmanual.

Model: LSS-INJ-6400SIG

Serial No.:

Applicant:

Companyname:

Address:

Department:

Personincharge:

TelNo.:

FaxNo.

Cut off this page "APPLICATION FORM FOR INSTRUCTION

MANUAL"from this volume andkeep itforfuture usewithcare.

When an INSTRUCTION MANUAL is required, fill in the above Application Form and

mailorfaxittothefollowingsalesdepartmentofourcompany.

To: NoiseLaboratoryCo.,Ltd.

1-4-4 Chiyoda Chuo-ku SagamiharaCity,

Kanagawa Pref., 252-0237 Japan

Tel: +81-(0)42-712-2051 Fax: +81-(0)42-712-2050

Cut

line

Memorandum

3. TABLE OF CONTENTS

1.IMPORTANT SAFETY PRECAUTIONS .................................................................. 1

2. APPLICATION FORM FOR INSTRUCTION MANUAL ....................... 3

3. TABLE OF CONTENTS

..................................................................................................... 5

4. PREFACE

.................................................................................................................................................. 6

4-1

PREFACE

............................................................................................................................................................... 6

4-2

UNCTIONSANDCAPABILITIES ........................................................................................................................... 6

5.BASICSAFETYPRECAUTIONS

......................................................................... 7

6. APPEARANCE OF THE UNIT

................................................................................ 9

7. HOW TO CONNECT EQUIPMENT

.............................................................. 11

7-1

ONNECTIONOF

EAR

ANEL

..................................................................................................................................11

7-2

ONNECTIONOF

RONT

ANEL

(

INCASEOF

LSS-6000

ERIES

) ..........................................................................11

7-3

ONNECTIONOFTHEFRONTPANEL

(

INCASEOF

LSS-6230) .................................................................................12

7-3

ETTING

HEN

RRESTORS

OUPLING

....................................................................................................................13

7-4

ETTING

HEN

APACITORS

OUPLING

...................................................................................................................15

8. BLOCK CHART

............................................................................................................................ 17

9. SPECIFICATIONS

.................................................................................................................... 18

10. ACCESSORIES

........................................................................................................................ 19

11. WARRANTY

................................................................................................................................... 20

12. MAINTENANCE

....................................................................................................................... 22

13. NOISE LABORATORY SUPPORT NETWORK

................. 23

4. PREFACE

4-1

PREFACE

We thank you for your purchase of the injection unit for the Lightening Surge Simulator LSS-6000

series:LSS-INJ6400SIG.ThismanualcontainshowtousetheLSS-INJ6400SIGandotherimportant

information. In order to obtain the highest performance from your LSS-INJ6400SIG, thoroughly

understandthecontentsofthismanualanduseasreadyreferenceforoperation.

The unit is the injection unit for tests for interconnection lines described in IEC61000-4-5.

Notice

The unit is just only for Lightening Surge Simulator (LSS-6000

Series).

For details about how to use Lightening Surge Simulator

(LSS-6000 Series), refer to the instruction manual of each

model.

4-2

Functionsand capabilities

1. The unit is used for the surge immunity tests for interconnection lines described

in IEC61000-4-5.

2. EUT’s power capacity is DC50V/1A. The unit can be used to inject high voltage

surge (maximum 6600V) to interconnection lines.

3. Bypassing 20mH inductor is available by connecting the connection plug in the

accessory to the inductor bypass terminal.

4. The protective arrestor in the accessory is attachable between each line and

ground.

5.BASICSAFETYPRECAUTIONS

1. As the unit outputs high voltage (6600V maximum) and great current

(157A maximum) by surge from LSS-6000 series, carefully handle it.

Mishandling or careless operation may result in a fatal wound. Do not touch the

surge in connector, DC line out connector, DC line in terminal in conducting

testsbecausehigh voltage isgenerated.

2. Use of the unit and the lightning surge simulator (LSS-6000 series) unit

in an explosive area such as "No fire" area etc is prohibited. If used in

such an area, it is liable to cause combustion or ignition due to

discharge.

3. Any person who has an implanted pacemaker in the body should not

operate this unit. Furthermore, such a person should not enter the test

area while this unit is operating. Otherwise, the electronic medical device

can malfunction so that can result fatal.

4. Mishandling or careless operation may result in fatal wounds.

5. Test equipment to be used with this unit should be capable of insulating against

at least a voltage of 6600V. The equipment under test (called EUT hereafter)

using this unit should be performed in a protective enclosure or cover against

scatteringbroken pieces, fireelectricshock,etc.

6. Do not touch surge in cables, line out cables etc. Otherwise, a fatal

accident may happen.

7. In case of touching the surge in connector, the socket of DC line out (the

hole for inserting the connection plug), and DC line in terminals just after

conducting tests, as it takes about 3 seconds for automatic elimination

of electricity of the lightening surge simulator, do not touch them for this

interval.

8. Never fail to connect PE terminal to the FG terminal of the lightening

surge simulator by PE cable (accessory).

9. EUT can be electrified by high voltage after injecting surge. Eliminate

electricity of EUT before touching it.

10. In case of touching DC line out connector, never fail to make high

voltage circuit “OFF” status by pressing STOP button or EMERGENCY

button.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NoiseKen Équipement de test

NoiseKen

NoiseKen 01-00006A Manuel utilisateur

NoiseKen

NoiseKen ESS-801 Manuel utilisateur

NoiseKen

NoiseKen LSS-F02 Series Manuel utilisateur

NoiseKen

NoiseKen GT-30R Manuel utilisateur

NoiseKen

NoiseKen FNS-AX4-A20-N2447 Manuel utilisateur

NoiseKen

NoiseKen 03-00074A Manuel utilisateur

NoiseKen

NoiseKen INS-AX2 Series Manuel utilisateur

NoiseKen

NoiseKen LSS-720B2 Manuel utilisateur

NoiseKen

NoiseKen ESS-S3011 Manuel utilisateur

NoiseKen

NoiseKen LSS-F03 Series Manuel utilisateur

NoiseKen

NoiseKen EPS-02Ev3 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur