NOCO Genius G26000 Manuel utilisateur

Welcome. Thank you for buying the NOCO Genius®

G26000. Read and understand the User Guide before

operating the charger. For questions regarding our

chargers, view our comprehensive support information at

www.no.co/support. To contact NOCO for personalized

support (not available in all areas), visit www.no.co/connect.

What’s In The Box.

• G26000 Smart Charger

• (1) Battery Clamp Connectors

• (1) Eyelet Terminal Connectors

• User Guide

• Information Guide and Warranty

User Guide

G26000V2.0

PRIOR TO USE, READ AND UNDERSTAND

PRODUCT SAFETY INFORMATION.

Failure to follow the instructions may result

in ELECTRICAL SHOCK, EXPLOSION,

or FIRE, which may result in SERIOUS

INJURY, DEATH, DAMAGE TO DEVICE or

PROPERTY. Do not discard this information.

DANGER

Contacting NOCO.

About G26000. The NOCO Genius®G26000 represents

some of the most innovative and advanced technology on

the market, making each charge simple and easy. It is quite

possibly the safest and most efcient charger you will ever

use. The G26000 is designed for charging all types of 12V

& 16V lead-acid and 12V lithium-ion batteries, including

Wet (Flooded), Gel, MF (Maintenance-Free), CA (Calcium),

EFB (Enhanced Flooded Battery), AGM (Absorption Glass

Mat), and LIB (Lithium Ion) batteries. It is suitable for

charging battery capacities from 25 to 500 Amp-Hours and

maintaining all battery sizes.

Getting Started. Before using the charger, carefully

read the battery manufacturer’s specic precautions and

recommended rates of charge for the battery. Make sure

to determine the voltage and chemistry of the battery by

referring to your battery owner’s manual prior to charging.

Mounting. The G26000 has four (4) external holes for

mounting. Mount the charger in a desired location with

#10 self-drill screws. Make sure there are no obstructions

behind the mounting surface. It is important to keep in mind

the distance to the battery. The DC cable length from the

charger, with either the battery clamp or eyelet terminal

connectors, is approximately 75-inches (1,900mm). Allow

for 12-inches (304mm) of slack between connections.

Charging Modes. The G26000 has eleven (11) modes:

Standby, 12V NORM, 12V COLD/AGM, 24V NORM,

24V COLD/AGM, 12V LITHIUM, 12V AGM+, 16V AGM,

16V LITHIUM, 13.6V SUPPLY and 12V REPAIR, plus

JumpCharge for engine starting. Some charge modes

must be pressed and held for three (3) seconds to enter

the mode. These “Press and Hold” modes are advanced

charging modes that require your full attention before

selecting. “Press and Hold” are indicated on the charger by

1.800.456.6626

[email protected]

30339 Diamond Parkway, #102

Glenwillow, OH 44139

United States of America

Phone:

Email:

Mailing Address:

222

a red line. It is important to understand the differences

and purpose of each charge mode. Do not operate the

charger until you conrm the appropriate charge mode

for your battery. Below is a brief description:

Mode Explanation

12V

NORM

Standby

12V

COLD/

AGM

14.8V | 26A | 50-500Ah Batteries

24V

NORM

29V | 13A | 25-250Ah Batteries

29.6V | 13A | 25-250Ah Batteries

No Power

14.5V | 26A | 50-500Ah Batteries

24V

COLD/

AGM

In Standby mode, the charger is not

charging or providing any power to

the battery. Energy Save is activated

during this mode, drawing microscopic

power from the electrical outlet. When

selected, an orange LED will illuminate.

For charging 12-volt Wet Cell, Gel Cell,

Enhanced Flooded, Maintenance-Free

and Calcium batteries. When selected,

a white LED will illuminate.

For charging 12-volt batteries in cold

temperatures below 50ºF (10ºC) or

AGM batteries. When selected, a blue

LED will illuminate.

For charging 24-volt Wet Cell, Gel Cell,

Enhanced Flooded, Maintenance-Free

and Calcium batteries. When selected,

a white LED will illuminate.

For charging 24-volt batteries in cold

temperatures below 50ºF (10ºC) or

AGM batteries. When selected, a blue

LED will illuminate.

Mode Explanation

12V

AGM+

16V

AGM

12V

LITHIUM

15.5V | 26A | 50-500Ah Batteries

13.6V | 5A | Max 6A

19.45V | 20A | 25-250Ah Batteries

14.2V | 26A | 50-500Ah Batteries

16.5V | 1.5A | Any Capacity

19.6V | 20A | 25-250Ah Batteries

12V

REPAIR

16V

LITHIUM

For charging 12-volt advanced AGM

batteries, which requires a higher

than normal charging voltage. When

selected, a blue LED will illuminate.

For charging 16-volt AGM batteries,

which are commonly used in racing

vehicles. When selected, a blue LED

will illuminate.

For charging 12-volt lithium-ion

batteries, including lithium iron

phosphate. When selected, a blue

LED will illuminate.

An advanced battery recovery mode

for repairing and storing, old, idle,

damaged, stratied or sulfated

batteries. When selected, a red LED

will illuminate and ash

For charging 16-volt lithium-ion

batteries, including lithium iron

phosphate, which are commonly used

in racing vehicles. When selected, a

blue LED will illuminate.

13.6V

SUPPLY

Converts to a DC power supply for

powering any 12VDC device, like a tire

inator, oil changer, or as a memory

retainer when replacing a battery. When

selected, a red LED will illuminate.

Press & Hold

444

Using 12V Lithium. [Press & Hold]

12V Lithium charge mode is designed for 12-volt

lithium-ion batteries only, including lithium iron

phosphate.

CAUTION. USE THIS MODE WITH CARE. THIS MODE

IS FOR 12-VOLT LITHIUM BATTERIES ONLY. LITHIUM-

ION BATTERIES ARE MADE AND CONSTRUCTED

IN DIFFERENT WAYS AND SOME MAY OR MAY NOT

CONTAIN A BATTERY MANAGEMENT SYSTEM (BMS).

CONSULT THE LITHIUM BATTERY MANUFACTURER

BEFORE CHARGING AND ASK FOR RECOMMENDED

CHARGING RATES AND VOLTAGES. SOME LITHIUM-

ION BATTERIES MAY BE UNSTABLE AND

UNSUITABLE FOR CHARGING.

Using 12V AGM+. [Press & Hold]

12V AGM+ charge mode is designed for 12-volt

advanced AGM batteries only. Advanced AGM batteries

are a new battery technology typically found in start-stop

micro-hybrid vehicles. These batteries accept a higher

than normal charging voltage around 15.5-volts. 12V

AGM+ charge mode is NOT suitable for traditional AGM

batteries. Consult the battery manufacturer before using

this mode.

CAUTION. USE THIS MODE WITH CARE. THIS

MODE IS FOR 12-VOLT LEAD-ACID ADVANCED

AGM BATTERIES ONLY. THIS MODE USES A HIGH

CHARGING VOLTAGE AND MAY CAUSE SOME WATER

LOSS IN WET (FLOODED) CELL BATTERIES OR

OVERCHARGE IN SOME BATTERIES.

Using 16V Lithium. [Press & Hold]

16V Lithium charge mode is for 16V lithium-ion batteries

only, including lithium iron phosphate batteries. 16-volt

lithium-ion batteries are commonly found in racing

vehicles, where the alternator might be removed, or used

to improve the performance of the injector or fuel pump.

CAUTION. THIS MODE IS FOR 16-VOLT LITHIUM

BATTERIES ONLY. LITHIUM-ION BATTERIES ARE

MADE AND CONSTRUCTED IN DIFFERENT WAYS

AND SOME MAY OR MAY NOT CONTAIN A BATTERY

MANAGEMENT SYSTEM (BMS). CONSULT THE LITHIUM

BATTERY MANUFACTURER BEFORE CHARGING AND

ASK FOR RECOMMENDED CHARGING RATES AND

VOLTAGES. SOME LITHIUM-ION BATTERIES MAY BE

UNSTABLE AND UNSUITABLE FOR CHARGING.

Using 16V AGM. [Press & Hold]

16V AGM charge mode is for 16V AGM batteries only. 16-

volt AGM batteries are commonly found in racing vehicles,

where the alternator might be removed, or used to improve

the performance of the injector or fuel pump.

CAUTION. USE THIS MODE WITH CARE. THIS MODE

IS FOR 16-VOLT AGM BATTERIES ONLY. DO NOT USE

ON A 12-VOLT BATTERY. CONSULT THE BATTERY

MANUFACTURER BEFORE CHARGING AND ASK FOR

RECOMMENDED CHARGING RATES AND VOLTAGES.

Using 13.6V Supply. [Press & Hold]

13.6V Supply converts the charger to a constant current,

constant voltage DC power supply. It can be used to power

12VDC devices, including; tire inators, oil changers, coffee

pots, seat heaters and more. As a power supply, it can also

be used to retain a vehicle’s on-board computer settings

during battery repair or replacement. 13.6V Supply provides

13.6-volts at 5A with overload protection at 6A (Max).

CAUTION. THIS MODE IS FOR 12-VOLT LEAD-ACID

BATTERIES ONLY. PRIOR TO USE, READ YOUR 12VDC

DEVICE MANUAL TO DETERMINE IF IT IS SUITABLE FOR

USE WITH THIS MODE. BOTH THE SPARK PROOF AND

REVERSE POLARITY SAFETY FEATURES ARE DISABLED

IN THIS MODE. DO NOT ALLOW THE POSITIVE AND

NEGATIVE BATTERY CLAMP OR EYELET TERMINAL

CONNECTORS TO TOUCH OR CONNECT TO EACH

OTHER AS THE CHARGER COULD GENERATE SPARKS.

CHECK THE POLARITY OF THE BATTERY TERMINALS

BEFORE USING THIS MODE.

Using 12V Repair. [Press & Hold]

12V Repair is an advanced battery recovery mode for

repairing and storing, old, idle, damaged, stratied or

sulfated batteries. Not all batteries can be recovered.

666

Batteries tend to become damaged if kept at a low

charge and/or never given the opportunity to receive

a full charge. The most common battery problems are

battery sulfation and stratication. Both battery sulfation

and stratication will articially raise the open circuit

voltage of the battery, causing the battery to appear

fully charged, while providing low capacity. Use 12V

Repair in attempt to reverse these problems. For optimal

results, take the 12-volt battery through a full charge

cycle, bringing the battery to full charge, before using

this mode. 12V Repair can take up to four (4) hours to

complete the recovery process and will return to Standby

when completed.

CAUTION. USE THIS MODE WITH CARE. THIS MODE

IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. THIS

MODE USES A HIGH CHARGING VOLTAGE AND MAY

CAUSE SOME WATER LOSS IN WET (FLOODED)

CELL BATTERIES. BE ADVISED, SOME BATTERIES

AND ELECTRONICS MAY BE SENSITIVE TO HIGH

CHARGING VOLTAGES. TO MINIMIZE RISKS TO

ELECTRONICS, DISCONNECT THE BATTERY BEFORE

USING THIS MODE.

JumpCharge.

JumpCharge is an innovative new feature for

jumpstarting low-voltage or dead vehicle batteries.

The JumpCharge process is much different than your

traditional battery charger with an “engine start” feature.

JumpCharge uses precision charge control to avoid

overloading the battery that shortens the life of your

battery.

To operate JumpCharge, the charger must be

connected to a 12-volt battery with the Battery Clamp

Connectors connected. Press the JumpCharge button

to begin jumpstarting your vehicle.

Once initiated, the Charge LEDs will begin showing the

progress of the JumpCharge from 25% to 100%.When

using this mode, the Charge LEDs do not display the

battery’s state-of-charge (SOC), only the JumpCharge

progress. Once the 100% green LED is illuminated solid,

and the 25%, 50% and 75% Charge LEDs are “off”, the

JumpCharge process is completed and your are ready to

start your vehicle. For optimal results, allow JumpCharge to

complete its ve (5) minute charge.

If unsuccessful when starting your vehicle, let the battery

rest for fteen (15) minutes and try JumpCharge again.

Most vehicles will start with one (1) JumpCharge, but

larger vehicles with dual battery systems, may require an

additional JumpCharge. If when pressing the JumpCharge

button, an Error Condition (Error LED and Standby LED

ashing) illuminates, the battery is below 2-volts. To

JumpCharge a battery below 2-volts, press and hold the

JumpCharge button for three (3) seconds, and JumpCharge

will being jumpstarting your battery.

CAUTION. USE THIS MODE WITH CARE. THIS MODE

IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. DO

NOT USE JUMPCHARGE MORE THAN TWO (2) TIMES

WITHIN A TWENTY-HOUR (24) HOUR PERIOD. IF TWO

(2) JUMPCHARGES CANNOT SUCCESSFULLY START

YOUR VEHICLE, HAVE YOUR BATTERY EVALUATED BY A

LOCAL BATTERY STORE.

Connecting to the Battery.

Do not connect the AC power plug until all other connections

are made. Identify the correct polarity of the battery terminals

on the battery. The positive battery terminal is typically

marked by these letters or symbol (POS,P,+). The negative

battery terminal is typically marked by these letters or symbol

(NEG,N,-). Do not make any connections to the carburetor,

fuel lines, or thin, sheet metal parts. The below instructions

are for a negative ground system (most common). If your

vehicle is a positive ground system (very uncommon), follow

Mode Explanation

Delivers 30A for ve (5) minutes to

jumpstart your dead vehicle battery.

When selected, a white LED will

illuminate. (Red Manual Mode)

5Min | 30A | 50-400Ah Batteries

Jump

CHARGE

888

the below instructions in reverse order.

1.) Connect the positive (red) battery clamp or eyelet

terminal connector to the positive (POS,P,+) battery

terminal.

2.) Connect the negative (black) battery clamp or eyelet

terminal connector to the negative (NEG,N,-) battery

terminal or vehicle chassis.

3.) Connect the battery charger’s AC power plug into a

suitable electrical outlet. Do not face the battery when

making this connection.

4.) When disconnecting the battery charger, disconnect

in the reverse sequence, removing the negative rst (or

positive rst for positive ground systems).

Begin Charging.

1.) Verify the voltage and chemistry of the battery.

2.) Conrm that you have connected the battery clamps

or eyelet terminal connectors properly and the AC power

plug is plugged into an electrical outlet.

3.) The charger will begin in Standby mode, indicated by

an orange LED. In Standby, the charger is not providing

any power.

4.) Press the mode button to toggle to the appropriate

charge mode (press and hold for three seconds to enter

an advanced charge mode) for the voltage and chemistry

of your battery.

5.) The mode LED will illuminate the selected charge

mode and the Charge LEDs will illuminate (depending on

the health of the battery) indicating the charging process

has started.

6.) The charger can now be left connected to the battery

at all times to provide maintenance charging.

LED Explanation

Maintenance

Green LED

25%

Red LED

The 25% Charge LED will slowly

pulse “on” and “off”, when the

battery is less than 25% fully

charged. When the battery is 25%

charged, the red Charge LED will

be solid.

50%

Red LED

During maintenance charging, the

100% Charge LED will pulse “on”

and “off” slowly. When the battery

is topped off and fully charged

again, the 100% Charge LED will

turn solid green. The charger can

be left connected to the battery

indenitely.

75%

Orange LED

The 50% Charge LED will slowly

pulse “on” and “off”, when the

battery is less than 50% fully

charged. When the battery is 50%

charged, the red Charge LED will

be solid.

The 75% Charge LED will slowly

pulse “on” and “off”, when the

battery is less than 75% fully

charged. When the battery is 75%

charged, the orange Charge LED

will be solid.

The 100% Charge LED will slowly

pulse “on” and “off”, when the

battery is less than 100% fully

charged. When the battery is fully

charged, the green LED will be solid,

and the 25%, 50% and 75% Charge

LEDs will turn “off”.

100%

Green LED

25% 50% 75% 100%

Understanding Charge LEDs.

The charger has four (4) Charge LEDs per bank - 25%,

50%, 75% and 100%. These Charge LEDs indicate the

connected battery(s) state-of-charge (SOC). See the

explanation below:

Autres manuels pour G26000

Table des matières

Langues :

Autres manuels NOCO Genius Chargeur de batteries

NOCO Genius

NOCO Genius G1100EU Manuel technique

NOCO Genius

NOCO Genius GENIUS2 Manuel technique

NOCO Genius

NOCO Genius G26000 Mode d’emploi

NOCO Genius

NOCO Genius Genius 2D Manuel technique

NOCO Genius

NOCO Genius GEN5X1 Manuel technique

NOCO Genius

NOCO Genius G7200 V2.0 Manuel utilisateur

NOCO Genius

NOCO Genius GENIUS1 Manuel technique

NOCO Genius

NOCO Genius G15000EU Manuel technique

NOCO Genius

NOCO Genius GENIUS 1 Manuel utilisateur

NOCO Genius

NOCO Genius GEN1 Mode d’emploi

NOCO Genius

NOCO Genius G750 Mode d’emploi

NOCO Genius

NOCO Genius Genius G1100 Manuel utilisateur

NOCO Genius

NOCO Genius GX2440 Manuel utilisateur

NOCO Genius

NOCO Genius GENIUS Series Manuel utilisateur

NOCO Genius

NOCO Genius GENIUS2 Manuel utilisateur

NOCO Genius

NOCO Genius GENIUS5 Manuel technique

NOCO Genius

NOCO Genius GENIUS10 Manuel technique

NOCO Genius

NOCO Genius Genius G7200 Manuel utilisateur

NOCO Genius

NOCO Genius GENIUS1AU Manuel technique

NOCO Genius

NOCO Genius GENIUS2X2 Manuel utilisateur

NOCO Genius

NOCO Genius G3500 Genius Manuel utilisateur

NOCO Genius

NOCO Genius G3500EU Manuel technique

NOCO Genius

NOCO Genius GENIUSPRO25 Manuel technique

NOCO Genius

NOCO Genius G26000 Manuel utilisateur

Manuels Chargeur de batteries populaires d'autres marques

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manuel utilisateur

Enelion

Enelion Vertica Manuel utilisateur

RCA

RCA CHU6 Manuel utilisateur

ANSMANN

ANSMANN ALCT 6/24-10 Manuel utilisateur

Hitachi

Hitachi UC 18YRSL Guide de dépannage

Olympus

Olympus B-20 LPC Manuel utilisateur

Exibel

Exibel ZH1708143 Manuel utilisateur

Lenmar

Lenmar Mach 1 Manuel utilisateur

CTEK

CTEK MXS 5.0 Manuel utilisateur

ABB

ABB HT842379 Manuel utilisateur

Nitecore

Nitecore Superb Charger SC4 Manuel utilisateur

Renogy

Renogy RBC2125DS-21W Manuel utilisateur

Braun

Braun BWC02M Manuel utilisateur

CTEK

CTEK MXS 3.6 Manuel utilisateur

Black & Decker

Black & Decker BDV090 Manuel utilisateur

Trinity

Trinity DPD Manuel utilisateur

Hulkman

Hulkman Sigma 1 Manuel utilisateur

IKEA

IKEA koppla Manuel utilisateur