NiteRider Evolution Manuel utilisateur

Halogen

NiMH

USER GUIDE

Evolution

NiteRider and Evolution are trademarks of NiteRider, Inc.

All other trademarks are the property of their respective owners.

The information in this document is subject to change without notice.

DISCOVER THE NIGHT!

Thank you for choosing the Evolution™ system from NiteRider,

the innovator in technical lighting systems. The Evolution is an

easy-to-use, high-intensity halogen system that can be

mounted to the frame or helmet.

To get the most from your NiteRider light, we urge you to

familiarize yourself with the following safety and operation

instructions.

PROTECTING

YOUR INVESTMENT

When not in use, always disconnect the headlamp from the

battery. To unplug, grasp the connector, not the cable.

Properly charge your battery to maximize its lifespan (see

“Battery Charging and Care” on page 10). To avoid damaging

your system, only charge your NiteRider battery with the

appropriate NiteRider charger.

While the Evolution will perform in wet weather conditions,

submerging it in water will damage the system. If you need a

submersible light, NiteRider manufactures industrial-grade

dive light systems. For information, contact NiteRider Dive

Lights at 858.268.3850 or visit www.niteriderdive.com.

RIDING AT NIGHT

While the Evolution will improve your control and enjoyment of

night riding, please remember that cycling at night is an

inherently dangerous activity. In addition to using your lighting

system properly and riding with extreme caution, NiteRider

urges you to:

• never ride alone

• always let someone know where you are going

• wear a helmet and reﬂective clothing

• carry an auxiliary light and emergency supplies.

NiteRider, Inc.

8205 Ronson Road, Suite E

San Diego, CA 92111 USA

800.466.8366

www.niterider.com

SUPPORT

If you experience difﬁculties during product installation or

operation, NiteRider provides free telephone support on

weekdays from 8:00 AM to 4:30 PM (Paciﬁc Time) at

800.466.8366, ext. 4. You may also e-mail us at

support@niterider.com.

WARRANTY

NiteRider stands behind its products with the following

warranties:

• Lifetime warranty on all mechanical components

• 1 year on cables and connectors, electronic components,

and printed circuit boards

• 180 days on rechargeable batteries

• 90 days on overnight chargers

• 60 days on halogen bulbs

To repair or replace your product while under warranty, return

it (postage prepaid and insured with original sales receipt) to

the address below. Out-of-warranty repair service is also

available. For complete warranty information, please visit our

website.

TABLE OF CONTENTS

Parts List and Identification

. . . . . . . . . . . . . . . . . . . . . . 4

Quick Start

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting the Headlamp

. . . . . . . . . . . . . . . . . . . . . . . . . 6

Universal Handlebar Mount . . . . . . . . . . . . . . . . . . . . . . 6

Helmet Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Inserting the Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting the Battery

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Frame Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pocket or Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Battery Charging and Care

. . . . . . . . . . . . . . . . . . . . . 10

Using the 9-hour Overnight Charger . . . . . . . . . . . . . . 10

Battery Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Run Time

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PARTS LIST

AND IDENTIFICATION

Please verify the contents of your Evolution system:

A. 10 Watt-6 Volt halogen headlamp

B. 4.0 Ah-6 Volt NiMH battery (pocket/frame mount)

C. Universal handlebar mount

D. Helmet mount

E. 9-hour overnight charger

F. 36” helmet cord

G. Velcro cable tie

QUICK START

1. Charge the battery for nine hours before the ﬁrst use. To

maximize the life of the battery, it is important to disconnect

the battery from the charger immediately after charging.

See “Using the 9-hour Overnight Charger” on page 10.

2. To mount the headlamp and battery, see “Mounting the

Headlamp” on page 6 and “Mounting the Battery” on

page 8.

3. Connect the battery to the headlamp or helmet cord.

4. To turn the lamp on and off, press and release the

headlamp power button.

MOUNTING THE HEADLAMP

The Evolution headlamp can be mounted to the handlebar or

a helmet.

Universal Handlebar Mount

The Universal Handlebar Mount (UHM) is designed to ﬁt on

virtually any handlebar. Included with the mount is a 2.5-mm

Allen wrench, a pair of black rubber bumpers already in

place, and a thin rubber shim to customize the ﬁt on large

handlebars up to 32 mm in diameter.

Turn the knob counter-clockwise, allowing the hinge to swing

open. Place the mount on the handlebar on the left side the

stem, orienting the rectangular notch in the slider clip to the

rear. Swing the hinge down to make contact with the

handlebar. Swing the hex bolt up, seating the knob into its

recess. Turn the knob clockwise to tighten and secure the

mount to the handlebar.

The UHM can be adjusted to accommodate any handlebar

angle. By loosening the 2.5 x 30 mm Allen screw, you can

move the swing arm back and forth to straighten the

headlamp. Tighten the 2.5 x 30 mm screw after the

adjustment.

NOTCH

SWING ARM

2.5 x 30 MM

SCREW

HINGE

KNOB

HEX BOLT

SLIDER CLIP

2.5 x 12 MM

SCREW

To pivot the headlamp, loosen the 2.5 x 12 mm screw located

under the slider clip and swing arm and rotate the headlamp

to the desired position. Make this adjustment before

tightening the 2.5 x 30 mm screw.

Helmet Mount

1. Unclamp the straps on each side

of the helmet mount and pull

them free.

2. Position the plastic mounting

plate as close to the centerline of

the helmet as possible, orienting

the parallel grooves on the slider

clip to the rear.

3. Feed each strap into and out of

two helmet vents, circling each

strap back to the upper edge of

the corresponding clamp.

4. Fasten the straps by inserting

them into the clamps.

Inserting the Headlamp into

the Handlebar or Helmet Mount

Insert the headlamp mount into the handlebar or helmet

mount slider clip from the rear of the slider clip forward.

Gently rocking the lamp as you slide it may help. Do not push

the release lever when inserting the headlamp into the slider

clip; let the lamp snap into place by itself.

To remove the headlamp, push the release lever and slide the

lamp backward.

Note

: After mounting the headlamp, adjust the headlamp so

it illuminates the road properly without distracting oncoming

riders.

MOUNTING THE BATTERY

The battery can be mounted to the bike frame or placed in a

jersey pocket, hydration pack, or fanny pack.

Warning

: For safety reasons, a cyclist should never be

tethered to the bike. If the headlamp is mounted to the

helmet, do not mount the battery to the frame. Conversely, if

the headlamp is mounted to the handlebar, do not place the

battery in a pocket or pack.

Frame Mount

1. Thread the wide Velcro tie

through the slots on the top of

the battery clip.

2. Attach the concave surface of

the battery to a safe, convenient

location on the frame (typically

under the top or down tube),

placing the Velcro strap over

the tube but under any shift or

brake cables.

3. Secure the handlebar cord to

the frame using the thin Velcro

tie. Make sure the cord does

not interfere with any moving

parts.

Pocket or Pack

1. Route the helmet cord through a

helmet vent or along the outside of

the helmet using the thin Velcro tie

to secure the cord.

2. Connect the helmet cord to the

battery, making sure the cord does

not interfere with any moving parts.

3. Simply place the battery in a

pocket or pack.

Table des matières

Autres manuels NiteRider Accessoires pour vélos

NiteRider

NiteRider PRO Series Manuel utilisateur

NiteRider

NiteRider PRO 2800 Manuel utilisateur

NiteRider

NiteRider MiNewt Dual Manuel utilisateur

NiteRider

NiteRider PRO 1800 Race Manuel utilisateur

NiteRider

NiteRider Pro Series Manuel utilisateur

NiteRider

NiteRider LUMINA MAX 2500 Manuel utilisateur

NiteRider

NiteRider RoadRat Manuel utilisateur

NiteRider

NiteRider Solas 250 Manuel utilisateur

NiteRider

NiteRider Lumina Micro 220 Manuel utilisateur

NiteRider

NiteRider Evolution Smart Manuel utilisateur

NiteRider

NiteRider MiNewt Mini 300-USB Manuel utilisateur

NiteRider

NiteRider PRO 1400 RACE Manuel utilisateur

NiteRider

NiteRider PRO 2200 RACE Manuel utilisateur

NiteRider

NiteRider FireStorm Manuel utilisateur

NiteRider

NiteRider PRO 2800 ENDURO REMOTE Manuel utilisateur

NiteRider

NiteRider MiNewt.200 Manuel utilisateur

NiteRider

NiteRider PRO 3600 DIY REMOTE Manuel utilisateur

Manuels Accessoires pour vélos populaires d'autres marques

Sigma

Sigma BC 16.16 Manuel utilisateur

Playcore

Playcore Dero Setbacks Manuel utilisateur

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuel utilisateur

Cateye

Cateye RAPID X2 Manuel utilisateur

buratti meccanica

buratti meccanica Clorofilla Trail Manuel utilisateur

Shimano

Shimano SG-8R20 Mode d'emploi

BOB

BOB YAK Manuel utilisateur

APLIC

APLIC 303303/20190717TW012 Manuel utilisateur

SRAM

SRAM AXS BlipBox Manuel utilisateur

Garmin

Garmin EDGE 500 Manuel utilisateur

Shimano

Shimano FD-RX810 Manuel utilisateur

Cateye

Cateye V2C - Manuel d'instructions

KMART

KMART 43115907 Manuel utilisateur

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuel utilisateur

NVO Components

NVO Components STEM Manuel utilisateur

DAXYS

DAXYS BP188 Manuel utilisateur

XLC

XLC BV-W17 Manuel utilisateur

Deda Elementi

Deda Elementi SUPERBOX Manuel utilisateur