Nice Titan 912L Manuel d'installation et d'exploitation
EN -Installation and reference manual
IMPORTANT -These instructions apply only to the 912L actuator. Control box
installation/operation is described in a separate control box manual.
Linear actuator
TITAN12L/12L1 912L
912L LA
TITAN 912L Linear Actuator
Installation Reference Manual
22
CONTENTS
SECTION 1: TITAN 912L ACTUATOR OVERVIEW .....................................3
SECTION 1: TOOLS NEEDED FOR INSTALLATION .................................4
SECTION 2: INSTALLATION SAFETY ........................................................4
SECTION 3: ACTUATOR - MECHANICAL INSTALLATION .......................5
3.1 MANUALLY SET GATE OPEN/CLOSE LIMITS .....................12
3.2 RUN ACTUATOR CABLE(S) TO CONTROL BOX .................13
3.3 936 CONTROL BOARD WIRING: PULL-TO-OPEN ...............14
3.4 936 CONTROL BOARD WIRING: PUSH-TO-OPEN ..............15
3.5 1050 CONTROL BOARD WIRING: PULL-TO-OPEN .............16
3.6 1050 CONTROL BOARD WIRING: PUSH-TO-OPEN ............17
3.7 SETTING ACTUATOR FINE LIMITS .......................................20
3.8 ACTUATOR CABLE REPLACEMENT WIRING ...................... 22
SECTION 4: PART DRAWINGS ....................................................................23
Warranty ..........................................................................................................24
TITAN 912L Linear Actuator
Installation Reference Manual
33
• TITAN 912L-1 = Actuator with 12’ harness
• TITAN 912L-2 = Actuator with 42’ harness
(dual gate only)
PIVOT ARM (P/N 1116)
ACTUATOR BOLT KIT
(P/N 1125)
GATE BRACKET,
BLACK
(P/N 10025215)
TITAN912L ACTUATOR PARTS IDENTIFICATION
PART# DESCRIPTION QTY
912L-1 Actuator With 12 foot Harness 1
912L-2 (DUAL GATE ONLY) Actuator With 42 foot Harness 1
1116 Pivot Arm 1
10025215 or PD0959A0000 Gate Bracket (Black) 1
1125 Actuator Bolt Kit 1
TITAN912L ACTUATOR SPECIFICATIONS
Drive Electromechanical Stainless Steel Screw
Gate Length And Weight Max. • Up to 600 lb. for 20 foot leaf (272 kg for 6 m)
• Up to 1000 lb for an 8 ft leaf (453 kg for 2.4 m)
Open/Close Time (To 90°) 14 - 16 seconds (adjustable)
Temperature Rating -4º to 122º F (-20º to 50º C)
Operating Voltage 12VDC
Actuator Dimensions (LxWxD) 43 x 4 x 6.75 inches (109.2x 10x 17.5 cm)
User Controls 936 or 1050 control board
Listed To Ul325 936, 1050, or Mercury 310 Control Boards:
Usage Class I, II, III, IV
Actuator Weight 19.75 pounds (8.96 kg)
Congratulations on selecting a Nice TITAN 912Lactuator. With proper selection, system design, installation and
maintenance this operator should provide years of reliable operation. This manual covers ONLY the installation
of the TITAN 912L actuator.
SECTION 1: TITAN 912L ACTUATOR OVERVIEW
IMPORTANT!
For control box installation, wiring, operation, maintenance instructions and all safety information,
refer to the appropriate control box installation manual used for the system being installed.
TITAN 912L Linear Actuator
Installation Reference Manual
44
Below is a list of tools necessary for installation of the Titan actuator:
• Welder (for pivot arm) unless optional bolt-on pivot arm (P/N 446) is used.
• Basic hand tools (screwdrivers, wrenches, pliers, etc..)
• Torx 25 tool (for removing actuator cover screws)
• Level (for ensuring pivot arm and actuator are level).
• Framing square (for determining pivot arm location)
• Torch/Chop Saw (for cutting pivot arm)
• Grinder (for sanding Pivot Arm)
SECTION 2: INSTALLATION SAFETY
SECTION 3: TOOLS NEEDED FOR INSTALLATION
WARNING
READALL SAFETYINFORMATION WHEN INSTALLINGASWING GATE SYSTEM! SEE EITHER OF THE
FOLLOWING MANUALS FOR SAFETY INFORMATION:
• CBOX936 Control Box Installation and Program Manual (with 936 controller).
• CBOX1050 Control Box Installation and Program Manual (with 1050 controller).
• MB1050 Control Box Installation an Program Manual (with 1050 controller).
• ACBOX/SolarBOX Installation and Program Manual (with Mercury 310 controller)
CAUTION
’Disconnect power at the control panel before making any electric service power connections.
’Be aware of all moving parts and avoid close proximity to any pinch points.
IMPORTANT!
’The gate operator installation is NOT a “do-it-yourself” project. Contract a qualied gate operator installation
company to install this system to ensure a safe and reliable installation.
’It is the responsibility of the property owner to ensure the installer is qualied to carry out the installation in
a safe and professional manner.
’Consult local government agencies for up-to-date rules and regulations to satisfy licensing, codes or
regulations that regulate automated gate system design and installation.
’The gate for which the gate operator is intended to be used should itself be installed correctly so that it is
level and plumb and the gate opens easily and evenly.
’Note that Nice swing gate systems are not intended for installation on an incline.
TITAN 912L Linear Actuator
Installation Reference Manual
55
LEFT SIDE VERTICAL VIEW
FIG-1A: "PULL TO OPEN" PIVOT ARM INSTALLATION
INSTALL PIVOT ARM TO GATE: PULL-TO-OPEN
1A
1. Securely mount the pivot arm to the hinge post (FIG-1A).
2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are
taken from the center of pivot of the gate hinge.
3. It is strongly recommended to weld the pivot arm to the hinge post.
TOP VIEW
6” 6”
13” 13”
SECTION 4: ACTUATOR - MECHANICAL INSTALLATION
PIVOTARM PIVOTARM
PIVOTARM
1/2”
HINGE POST
CENTER OF HINGE
CENTER LINE OF
ATTACHMENT POINT
FOR GATE BRACKET
CENTER OF HINGE
GATE CLOSED
DIRECTION OF OPENING
HINGE POST HINGE POST
NOTICE
Welding is much
preferred, but Nice
offers an optional
bolt-on pivot arm
(P/N 446) for when
welding is not
possible.
CAUTION
Never weld parts to the gate or posts when the control board
is powered to avoid irrepairable damage to the circuit board!
TITAN 912L Linear Actuator
Installation Reference Manual
66
FIG-1B: "PUSH TO OPEN" PIVOT ARM INSTALLATION
1B
1. Securely mount the pivot arm to the hinge post (FIG-1B).
2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are
taken from the center of pivot of the gate hinge.
3. It is strongly recommended to weld the pivot arm to the metal post.
INSTALL PIVOT ARM TO GATE: PUSH-TO-OPEN
TOP VIEW
6” 6”
11” 11”
PIVOTARM
PIVOTARM
PIVOTARM
1/2”
HINGE POST
CENTER OF
HINGE
HINGE POST HINGE POST
CENTER LINE OF
ATTACHMENT POINT
FOR GATE BRACKET
CENTER OF HINGE
GATE CLOSED
DIRECTION OF OPENING
LEFT SIDE VERTICAL VIEW
CAUTION
Never weld parts to the gate or posts when the control board
is powered to avoid irrepairable damage to the circuit board!
NOTICE
Welding is much
preferred, but Nice
offers an optional
bolt-on pivot arm
(P/N 446) for when
welding is not
possible.
TITAN 912L Linear Actuator
Installation Reference Manual
77
2MOUNT ACTUATOR TO PIVOT ARM
FIG-2A: INSTALLING ACTUATOR TO PIVOT ARM
FIG-2B: LEVEL ACTUATOR
(GATE OPEN)
FIG-2C: LEVEL ACTUATOR
(GATE CLOSED)
1. Mount actuator to pivot arm as shown in FIG-2A using 1/2” bolt and lock nut. Tighten until secure.
2. Use bubble level to ensure actuator is level and plumb in both open and closed positions.
1/2”x 3.5” BOLT
ACTUATOR
1/2”LOCK NUT
PIVOTARM
PIVOTARM
CABLE LOOP
LEVEL
LEVEL
LEVEL
LEVEL
ACTUATOR
IMPORTANT!
’When using a bubble level to ensure pivot arm/
actuator are plumb and level, check in both open
and close positions per FIG-2B and 2C.
’Ensure that actuator mounting hardware is tight
enough to prevent movement, vibration, wobble,
or shifting when the actuator is in operation.
’Note cable loop (FIG-2C) to allow strain relief for
cable during actuator0 movement.
TITAN 912L Linear Actuator
Installation Reference Manual
88
AFFIX GATE BRACKET TO ACTUATOR ARM
3
1/2”x 2” PIVOT BOLT
1/2”x 2” PIVOT BOLT
GATE BRACKET
(SIDE VIEW)
GATE BRACKET
ACTUATOR
ARM
1/2” LOCK NUT
WASHER (ZINC)
ACTUATOR
ARM
FIG-3A: AFFIXING GATE BRACKET TO ACTUATOR ARM
FIG-3B: GATE BRACKET HARDWARE REQUIREMENTS
WASHER
WASHER
(STAINLESS STEEL)
LOCK NUT
If the gate bracket is not already installed on the actuator arm, mount gate bracket to actuator arm with the
pivot bolt, nut, and washers per images below.
WASHER
TITAN 912L Linear Actuator
Installation Reference Manual
99
1. Place gate in:
a) CLOSED position for PUSH-TO-OPEN congurations (FIG-4A).
b) OPEN position for PULL-TO-OPEN conguration (FIG-4B).
2. With actuator arm fully retracted, rotate entire actuator on the pivot arm around until the gate bracket
attached to the actuator is positioned on a supporting structure of gate.
3. Mark position of gate bracket on gate or clamp into position.
4POSITION GATE BRACKET ON GATE
GATE OPEN (PULL-TO-OPEN)
FIG-4B: PULL-TO-OPEN GATE BRACKET LOCATION
ACTUATOR
PIVOT
ARM GATE BRACKET
LOCATION
TRAFFIC DIRECTION
ARMATURE FULLY
RETRACTED
WALL
HINGE
HINGE
POST
FIG-4A: PUSH-TO-OPEN GATE BRACKET LOCATION
GATE CLOSED (PUSH-TO-OPEN)
GATE BRACKET
LOCATION
TRAFFIC
DIRECTION
ARMATURE FULLY
RETRACTED
WALL
HINGE
POST HINGE
PIVOTARM
ACTUATOR
TITAN 912L Linear Actuator
Installation Reference Manual
1010
1. Weld the gate bracket to the gate supporting structure (FIG-5A) or use supplied 3/8” bolts and
nuts from kit (FIG-5B).
2. If welding is not possible, drill two holes to match bracket mounting holes and afx with two
3/8”x2.5” screws and 3/8” nuts included in the kit (FIG-5B).
FIG-5A: GATE BRACKET WELDED TO GATE
FIG-5B: GATE BRACKET AND HARDWARE (BLACK BRACKET SHOWN)
5AFFIX GATE BRACKET TO GATE
GATE BRACKET
3/8”x2.5” HEX BOLT (x2)
WELD
3/8” NUT (x2)
IMPORTANT!
Ensure bracket centerline is 1/2” above the top of the pivot arm.
IMPORTANT!
Use a bubble level to assure after mounting that actuator is level and plumb.
CAUTION
Never weld parts to the gate or posts when the control board
is powered to avoid irrepairable damage to the circuit board!
NOTICE
Attach gate bracklet
only to structural
supports. If unsure of
exact bracket location,
tack weld or clamp until
gate can be tested.
Autres manuels pour Titan 912L
3
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Nice Contrôleurs
Nice
Nice Elero ExitSafe 28 388.0001 Manuel utilisateur
Nice
Nice MG3000 Manuel utilisateur
Nice
Nice Mercury 310 Manuel utilisateur
Nice
Nice ROX600 Caractéristiques techniques
Nice
Nice Apollo 816 LA Manuel d'installation et d'exploitation
Nice
Nice PLUTO PL 4000 Manuel de l'installateur
Nice
Nice To-Max Manuel du produit
Nice
Nice Robus 600 Manuel de la liste des pièces
Nice
Nice One-Max Manuel du produit
Nice
Nice UST1K-1.1kW Guide de démarrage rapide
Nice
Nice GEFEN GF-AVIP-MC Manuel utilisateur
Nice
Nice ROBO PLUS Manuel de service
Nice
Nice Mercury 310 Mode d’emploi
Nice
Nice HySecurity 1500 Series Manuel d'installation et d'exploitation
Nice
Nice SPA30 Manuel de service
Nice
Nice M-BOARD Guide de démarrage rapide
Nice
Nice 1551 Manuel utilisateur
Nice
Nice METRO ME 3000 Manuel utilisateur
Nice
Nice Patio Series Caractéristiques techniques
Nice
Nice Max Manuel du produit
