NHR S05-R Manuel utilisateur

S05-R User’s Manual

S05-R User’s Manual (ZigBee HA Profile) Ver. 1.11

Nietzsche Enterprise reserves the right to make changes and improvements to its products without notice.

Contact Information: Email: zigbeenhr@shop, Website: www.shop-wifi.com/wireless-sensors

Content

1) Package Content and S05-R View ................................................................................................. 2

2) Installing Mounting for S05-R and Initial Power On...................................................................... 3

3) Joining S05-R to the Network ....................................................................................................... 4

4) Removing S05-R from the Parent’s Network................................................................................ 4

5) Testing Communication Quality and Joining an End Device Using S05-R .................................... 5

6) Removing an End Device from the Parent’s Network .................................................................. 5

7) ZigBee Reset.................................................................................................................................. 5

8) S05-R LED Status and S1 Link Switch Actions ............................................................................... 6

9) Product Specifications .................................................................................................................. 7

S05-R User’s Manual

Congratulations for choosing a world-class ZigBee range extender. This manual is designed to

help set up and get the most from the sensor in a few short minutes.

Safety notice: Please read and follow the instructions before using this product

To prevent electrical shock or fire, do not disassemble or expose the unit to liquids of any kind

Only use attachments and / or accessories specified by the manufacturer

1 Package Content and S05-R View

NHR S05-R range extender

Power adaptor

Mounting fixtures

(mounting cradle; 2 wall plugs; 2 screws)

Important: To ensure IP66 waterproof and dust tight operations, both cover and connector must be

fully tightened (clockwise).

Anti-UV Plastic

Enclosure

Link Switch (S1)

IP 66 Waterproof &

Dust Tight Cover

IP66 Waterproof &

Dust Tight Connector

Power Cable

Status LED

Product Serial Number &

Unique MAC Address

S05-R User’s Manual

2 Installing Mounting for S05-R and Initial Power On

Requirements:

Mounting fixtures

Drill with 5mm (approx. 0.2 inches) drill bit size (if using wall plugs) or 3.5mm (approx. 0.14

inches) drill bit size (if not using wall plugs)

Size 1 Phillips screwdriver

a) Locate S05-R with at least 15cm (approx. 6 inches) spacing on each side (except on mounting side)

avoiding the following sources of interference: direct sunlight, air ﬂow from vents, fans, doors,

windows, heaters, sources of steam, oil vapor, etc.

b) If necessary, pre-drill mounting holes using mounting cradle for alignment, then use appropriate

drill bit –5mm (approx. 0.2 inches) if using wall plugs or 3.5mm (approx. 0.14 inches) if not using

wall plugs.

c) If necessary, insert wall plugs into the 2 holes and use size 1 Phillips screwdriver to fasten the

screws securing the mounting cradle. Note: pay careful attention to the orientation of the

mounting cradle.

d) Install and remove S05-R by placing it into and lifting it out of the cradle.

Install - Remove -

Note: For optimal wireless performance, ensure S05-R is installed with antenna straight up.

e) Connect S05-R’s USB connector to USB power adaptor and plug into a live AC mains socket. The

status LED on S05-R (through translucent cover) should start flashing to indicate its current state:

Green LED

Status

1 flash every 5 seconds

Ready to join a parent device

1 flash every 2 seconds

Already joined a parent device and functioning normally

2 flashes every 5 seconds

Already joined but unable find a parent device in the same network

S05-R User’s Manual

3 Joining S05-R to the Network

Requirements:

Parent device, such as coordinator (eg. WZB-01USBC, WZB-02485C), gateway (eg. G07-W,

WZB-05ET), or router (eg. WZB-01USBR, WZB-02485R)

a) Ensure parent device is powered on (see relevant device’s manual).

b) Power on S05-R (see “Installing Mounting for S05-R and Initial Power On” section) ensuring it is in

Ready to Join status (green LED flash once every 5 seconds).

c) Enable Permit Join status on parent device (see relevant device’s manual) and check S05-R joined

the parent device.

d) If S05-R has successfully joined the parent device, S05-R will show Successfully Joined status (green

LED flash 3 times) then Normal Operations status (green LED flash once every 2 seconds).

If S05-R does not show Normal Operations status (green LED flash once every 2 seconds), then it has

not successfully joined. Repeat above steps until S05-R has joined successfully. If S05-R has still not

joined after a few attempts, check it is within the operational range of 500m (line of sight) from the

parent device and away from other 2.4GHz devices that might interfere with its operations.

If S05-R has joined successfully, but shows Disconnected status (green LED flashes twice every 5

seconds), then check parent device is correctly powered on. If the parent device is functioning

correctly, S05-R may be out of range or experiencing interference, additional extender(s) may need to

be added to ensure good connections.

4 Removing S05-R from the Parent’s Network

Requirements:

Sharp pointed tool

a) Ensure parent device is powered on (see relevant device’s manual).

b) Ensure S05-R is powered on (see “Installing Mounting for S05-R and Initial Power On” section) and

has already joined the parent’s network (green LED flash once every 2 seconds).

c) Twist the base counterclockwise to gain internal access to the transmitter, being careful when

separating the base to ensure the power cable connector stays connected.

d) Use a sharp pointed tool to apply 3 quick presses to the S1 link switch, S05-R will show Removing

status (red LED rapid flash for up to 30 seconds) or until successful removal (green LED flash once).

e) If S05-R has been successfully removed, S05-R will show Ready to Join status (green LED flash once

every 5 seconds).

S05-R User’s Manual

5 Testing Communication Quality and Joining an End Device Using S05-R

Requirements:

Sharp pointed tool

a) Ensure S05-R is powered on (see “Installing Mounting for S05-R and Initial Power On” section) and

has already joined the parent’s network (green LED flash once every 2 seconds).

b) Twist the base counterclockwise to gain internal access to the transmitter, being careful when

separating the base to ensure the power cable connector stays connected.

c) Use a sharp pointed tool to apply 1 quick press to the S1 link switch on S05-R to initiate Nearest

Router Communication Quality (NRCQ), the status is indicated below:

S05-R LED

Status

Green LED for 5 seconds

Good NRCQ –No additional extender required

Green & Red LED alternating for 5 seconds

Fair NRCQ –Additional extender(s) recommended

Red LED for 5 seconds

Poor NRCQ –Additional extender(s) required

d) After 10 seconds of NRCQ, S05-R will enter Permit Join status for 60 seconds (green LED flash twice

every 3 seconds), other devices may join the network via S05-R during this period.

e) If a device joined the network, S05-R’s will show Device Joined status (red LED flash twice).

f) After 60 seconds of Permit Join status, S05-R will revert to Normal Operations status (green LED

flash once every 2 seconds).

6 Removing an End Device from the Parent’s Network

Initiate end device remove (see relevant device’s manual), if the end device was successfully removed,

S05-R will show Device Removed (red LED flash 3 times).

7 ZigBee Reset

In the case where the parent devices (coordinator, gateway, or router) for S05-R are no longer

available or have been reset, S05-R will need to be reset by applying a 5-second press to the S1 link

switch, the green & red LEDs will both come ON during the reset, then S05-R should show Ready to

Join status (green LED flash once every 5 seconds).

Recommendation: It is strongly recommended to disconnect S05-R from the power source if it is not

in use to reduce wireless traffic & interference and unintended joining to a network.

S05-R User’s Manual

8 S05-R LED Status and S1 Link Switch Actions

The S05-R LED status can be seen through the translucent cover and is summarized below:

S05-R LED

Status

Green LED:

1 flash every 5 seconds

Ready to Join –ready to join network of parent device

(coordinator, gateway, or router)

Green LED:

3 flashes (one time)

Successfully Joined –joined network of parent device

Green LED:

1 flash every 2 seconds

Normal Operations –joined network of parent device and

functioning normally

Green LED:

2 flashes every 5 seconds

Disconnected –joined network, but unable to find any

parent device of the network

Green LED:

ON for 5 seconds

Good NRCQ –no additional extender required

Green & RED LED:

Alternate for 5 seconds

Fair NRCQ –additional extender(s) recommended

Red LED:

ON for 5 seconds

Poor NRCQ –additional extender(s) required

Green LED:

2 flashes every 3 seconds

Permit Join –permit requests from other devices (routers /

end devices) to join the network

Red LED:

2 flashes (one time)

Device Joined –device (router / end device) joined the

network

Red LED:

3 flashes (one time)

Device Removed –device (router / end device) successfully

removed from the network

Red LED:

Rapid flashing up to 30 seconds

Removing –being removed from the network of the parent

device

Green & Red LED:

ZigBee Reset –reset to factory default, remove all ZigBee

network linkages

The S05-R S1 link switch actions are summarized below:

Operation

S1 Link Switch Actions

NRCQ (first 10 seconds)

Permit Join (next 60 seconds)

Press once

Remove from Network

Press 3 times within 1.5 seconds

ZigBee Reset

Press and hold for 5 seconds

S05-R User’s Manual

9 Product Specifications

Thank you for choosing the S05-R. We are looking forward to working with you!

Wireless Protocol

Compliant IEEE 802.15.4 ZigBee2007/PRO HA Profile

Operating Frequency

2.4GHz ISM Band

Transmission Range

500m (1640ft) line of sight

RF Output Power

18dBm

Receiver Sensitivity

-92dBm

Power Consumption

0.3W

Power Supply

DC5V

Network Topology

Star / Tree / Mesh

Operating Environment

-10˚C to 50˚C (14˚F to 121˚F), 0-95% RH

Dimensions

130(H) x 50()mm (5.1(H) x 1.9() inches)

Weight

265 g (9.34 oz)

Certifications

CE / FCC / NCC, IP66 grade waterproof & dust tight protection

Table des matières

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur