Newport 0901 Manuel utilisateur

USER’S GUIDE

±15 V Current-Limited Power Supply

Model 0901

phone: (877) 835-9620

e-mail: tech@newport.com • www.newport.com

EU Declaration of Conformity

We declare that the accompanying product, identified with the CE mark,

complies with requirements of the Electromagnetic Compatibility Directive

2004/108/EC and the Low V oltage Directive 2006/95/EC.

Model Numbers: 0901

Year mark afﬁxed: 2013

Type of Equipment: Electrical equipment for measurement, control and

laboratory use in industrial locations.

Manufacturer: Newport Corporation

1791 Deere A venue

Irvine, CA 92606

Standards Applied:

Compliance was demonstrated to the following standards to the extent

applicable:

BS EN61326-1: 2005/2006 “Electrical equipment for measurement, control and

laboratory use – EMC requirements” for use in a controlled electromagnetic

environment.

This equipment meets the CISPR 11:2011 radiated and conducted emission

limits.

BS EN 61010-1:2011, “Safety requirements for electrical equipment for

measurement, control and laboratory use”.

Mark Carroll

Sr. Director, Instruments Business,

Newport Corporation

Warranty

Newport Corporation guarantees its products to be free of defects for one

year from the date of shipment. This is in lieu of all other guarantees,

expressed or implied, and does not cover incidental or consequential loss.

Information in this document is subject to change without notice. Copyright

logo and symbol are registered trademarks of Newport Corporation

Document Number 90061076 Rev. A

Model 0901 User Guide

Contents

Warranty........................................................................................2

Important User Safety Information ................................4

General Warnings ............................................. 4

Definitions and Symbols .................................. 5

Environmental Specifications ......................... 5

Contact Information ......................................... 6

Introduction.................................................................................7

Getting Started ............................................................ 8

Voltage and Fuse Selection .............................. 8

Operation..................................................................................10

Output Characteristics ................................... 10

Cables .............................................................. 11

Customer Service ...............................................................12

Technical Support ........................................... 12

Service ............................................................. 12

IMPORTANT USER SAFETY INFORMATION

–DO NOT DISCARD

General warning in the event of a hazard

• Donotposition this device insuch amanner that

would make it difficult to disconnect the power cord

from the device or the power source.

• Position the equipment so that access tothe mains

disconnect ON/OFF switch on the front panel readily

available.

• Pushthe powerON/OFFswitch inthe frontofthe

device to OFF position to turn OFF the power to

the internal electronics. The OFF position: push the

actuator or switch rocker arm so the “O” depressed.

(To connect power to device, push the actuator or

switch rocker arm so the “1” depressed).

• Fullydisconnect the powercordofthe device from

MAIN power.

Grounding and Powering the device

• Verifythat the line voltage setting onthe rearofthe

Power Supply Model 0901 matches the local Main

Power from the power cord.

• Verifythat properfuses installed foramps andtime

delay.

• Toavoid electronic shock, connect the instrument to

properly earth-ground, 3-prong receptacles by using

the supplied power cord only . Failure to observe this

precaution can reduce equipment performance.

General warning and precaution

• Donotattempttooperatethisequipmentifthereis

evidence of shipping damage or you suspect the unit is

damaged.

• Theusershouldnotattemptanymaintenanceor

service of the device beyond the procedures outlined in

this manual. Any problem that cannot be resolved

should be referred to Newport Technical Support.

Model 0901 User Guide

Deﬁnitions and Symbols

The following terms and symbols are used in this

documentation and appear on the Model 0901 Power

Supply where safety-related issues occur.

Electronic shock – This symbol indicates a hazard

arising from dangerous voltage. Any mishandling could

result in irreparable damage to the equipment and

personnel injury .

ON Symbol – This symbol represents Power On

OFF Symbol – This symbol represents Power Off

Attention – Refer to the operator instructions of manual

before operating equipment.

Voltage Requirements 100/120/220/240 ~VAC, 47.5-66Hz

Electrical Ratings 100-120~VAC, 0.5A; and 220-

240~VAC, 0.25A (47.5-660Hz)

Size (H x W x D) [in. (mm)] 3.5 (90.0) x 7.65 (195.0) x 8.0 (200.0)

Mainframe Weight [lb (Kg)] 6.5 (2.8)

Operating Temperature 10ºC to 40ºC (<90% humidity non-

condensing)

Storage T emperature 0ºC to + 50ºC (<90% humidity non-

condensing)

Relative Humidity , Storage <90% humidity non-condensing

Altitude <3000 meters (10000 feet)

Installation Category II

Pollution Degree 2

Use Location Indoor use only

Environment Speciﬁcation

The power entry module requires two 5x20 mm, Slo-Blo fuses. The table

below identifies the correct voltage selector switch setting and fuse rating

for several common AC power .

Input Power Voltage

Switch Setting Fuse Type

100 VAC 100 A

120 VAC 120 A

220 VAC 220 B

240 VAC 240 B

Fuse Type A: Slo-Blo, 250 V , 0.5 A, i 2t ≥ 1.985 A2s, 5 mm x 20 mm

Fuse Type B: Slo-Blo, 250 V , 0.4 A, i 2t ≥ 1.36 A2s, 5 mm x 20 mm

Note: The AC power module requires two fuses. The fuse speciﬁcations must match all listed

speciﬁcation requirements to ensure proper operation.

Model 0901 User Guide

Introduction

The Newport Model 0901 Power Supply is a triple output,

low-noise, ±15-V DC power supply. It is intended for use

with all Newport brand products which require ±15-V DC,

and can also serve as a general purpose supply for laboratory

use. It is capable of simultaneously powering three devices,

each requiring ±15 V and up to 300 mA. Two of the outputs

are provided via three-pin M8 style connectors (compatible

with other Newport products), while the third uses banana

jacks. (See Figure 1.)

Figure 1: Model 0901 front panel.

Getting Started

Voltage and Fuse Selection

The Model 0901 can operate with an input of 100, 120,

220, or 240 V AC with AC frequencies of 47–63 Hz.

The unit is configured for 120 V AC at the factory; if it will

be used with a different AC voltage, this will need to be

selected on the power module on the back panel. The fuses

may also need to be changed. See below.

To check the voltage setting, look at the voltage indicator

on the AC power module on the back of the power

supply . (See Figure 2.)

Figure 2: Model 0901 rear panel showing AC power module & voltage indicator.

To change the voltage/fuses:

1. Make sure the power supply is turned off.

2. Disconnect the AC power cord.

3. Open the cover of the power module using a small

blade screwdriver or similar tool.

Model 0901 User Guide

Figure 3: Power module with the cover open

4. Remove the AC-voltage selection wheel from the unit.

Do not attempt to rotate the wheel while it is still

in the power module; the wheel must be removed,

turned, and then reinserted for proper operation.

(See Figure 3.)

5. Reinsert the wheel in the module so the desired AC

voltage can be viewed in the power-module window.

6. Ensure the proper fuses for the new AC voltage are

installed (see Table 1). Pull out fuse holders to replace

if needed.

7. Close the power-module cover.

8. Verify the proper voltage is showing through the

module window.

9. Reconnect the AC power cord.

Fuse Type A: Slo-Blo, 250 V, 0.5 A, i2t ≥ 1.985 A2s, 5 mm x 20 mm

Fuse Type B: Slo-Blo, 250 V, 0.4 A, i2t ≥ 1.36 A2s, 5 mm x 20 mm

Table 1: The AC power module requires two 5x20-mm, 250-V, Slo-Blo fuses. The current ratings of

the fuses should be as shown.

Input Power Voltage Setting Fuse Type

100 VAC 100 A

120 VAC 120 A

220 VAC 220 B

240 VAC 240 B

Operation

Output Characteristics

The outputs (three pairs of ±15 V) of the Model 0901

are all derived from a common linear supply, but each

incorporates independent current-limiting protection as

shown in Figure 4. As a result, the voltage on each

output differs slightly. The impedance of each output is

approximately 2 ohms, so an output will be reduced by

0.6 V when providing the full 300 mA. With no load,

outputs should be ±15 V ±3%.

When a load attempts to draw in excess of 300 – 330 mA

the protection is activated. This is accomplished by

reducing the voltage in order to limit the current to the

maximum rated current.

Figure 4: Block diagram and pin assignments (as seen on front panel) of the Model 0901 power

supply.

Table des matières

Autres manuels Newport Alimentation

Newport

Newport ORIEL INSTRUMENTS OPS-A150 Manuel utilisateur

Newport

Newport LDX-3232 Manuel utilisateur

Newport

Newport Oriel Instruments 70706 Manuel utilisateur

Newport

Newport iDRN-PS-1000 Manuel utilisateur

Newport

Newport Oriel OPS-Q250 Manuel utilisateur

Newport

Newport ORIEL INSTRUMENTS OPS-A150 Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur