NewMar PC-10 Guide de configuration
The PC noise filter is designed to reduce electrical noise, which is generated by engines and
electronic accessories, allowing receivers and audio equipment to operate properly. Functioning as
a power conditioner, this model filters both the positive and negative leads in the system and can be
applied at the noise source and/or at the affected equipment.
Sources of noise which the PC will effectively filter include: fluorescent lights, radars, fans,
blowers, pumps, converters, inverters, autopilots or other electronic equipment which draws up to
10 or 25 amps (depending on model). By applying filters at the source, the noise can be silenced
before it can contaminate the entire system.
When installed in the power line to electronics which are affected by interference, the PC suppresses
residual noise which may be present in the system. This allows proper operation of VHF radios,
depth sounders, loud hailers, AM/FM receivers and stereo systems.
A brief analysis of your system may be worthwhile to determine the best location for your filters.
One method used to identify noise sources is to switch on accessories one at a time noting the
effects upon your electronic gear. If noise is detected when a particular item is turned on, it is best to
filter that device at the source. If one source cannot be identified, it may be best to install the filter(s)
close to the affected unit(s).
After you have determined the best location in the system, locate a flat surface close to the power
line that requires filtering. For best results, the filter should be within 24" of the device you are
filtering. The case does not require grounding, so it is acceptable to mount the filter on either
metallic or non-metallic surfaces. Securely attach the filter using the hardware provided, noting the
input and output leads (see diagram).
Shut off power to the power leads at the battery or distribution panel. Identify the positive and
negative power leads and cut at an appropriate point. Noting input and output and carefully
observing correct polarity, use the wire splices provided to attach the filter leads to the power leads.
(See diagram for typical installation.)
MAXIMUM INPUT VOLTAGE (both models): 50 VDC
MAXIMUM INPUT/OUTPUT CURRENT:
15 AMPS INTERMITTENT, 5 MINUTES MAX, 20% DUTY
10 AMPS CONTINUOUS, 100% DUTY
35 AMPS INTERMITTENT, 5 MINUTES MAX, 20% DUTY
25 AMPS CONTINUOUS, 100% DUTY
FILTERED FREQUENCY RANGE (both models): AUDIO - 200 MHz
PC-10:
PC-25:
PC Noise Filters
Models: PC-10, PC-25
GENERAL INFORMATION
INSTALLATION
RATINGS
CAUTION: Correct polarity and input/output connection must be maintained.
Failure to do so may result in damage to the filter and/or equipment being filtered.
M-PCINST-C
As of Jun. 2018
R
DC Power OnboardSM
www.newmarpower.com
Phone: 714-751-0488
Fax: 714-896-9679
E-Mail: techservice@newmarpower.com
15272 Newsboy Circle,
Huntington Beach,
CA 92649
1.38"
(35.0mm)
RED
INOUT
ORANGE
BLACK BLACK
PC-Filter
Transceiver
Stereo, etc.
RED
IN
OUT
ORANGE
BLACK
BLACK
Motor
PC-Filter
2.08"
(53.0mm)
Fig. 2) Typical Installation
When Filtering Noise Source
Fig. 1) Typical Installation
When Filtering Affected Equipment
PC-25
Schematic And Dimensions
RED
BLACK
IN OUT
BLACK
ORANGE
R
DC Power OnboardSM
www.newmarpower.com
Phone: 714-751-0488
Fax: 714-896-9679
E-Mail: techservice@newmarpower.com
15272 Newsboy Circle,
Huntington Beach,
CA 92649
RED
BLACK
IN OUT
BLACK
ORANGE
PC-10
Schematic And Dimensions
Note: WIRE LENGTH is the length
of the wire run from the Input to the Output
of the PC-10 unit
combined
Up to 10'
26' - 40'
#12 2.1f
#14 f1.6
11' - 25'
#10 2.6f
Note: WIRE LENGTH is the length
of the wire run from the Input to the Output
of the PC-25 unit
combined
WIRE SIZE TABLE
WIRE SIZE TABLE
Up to 10'
Wire Length Size (AWG) Size (mm)
Wire Length Size (AWG) Size (mm)
26' - 40'
#10 2.6f
#12 2.1f
11' - 25'
#8 3.3f
M-PCINST-C
As of Jun. 2018
(+) Orange
(+) Red
2.99"
(76.0mm)
2.49"
(63 4mm).
f0 22"(5 6mm)x4plcs..
2.88" (73.2mm)
3.49" (88.8mm)
(--) Black
(--) Black
PC-10
POWER CONDITIONER
NOISE FILTER
10 AMPS, 6-48 VDC
POS OR NEG GND
ORANGE
BLACK
RED
BLACK
INPUT
OUTPUT
HUNTINGTON BEACH, CA. USA
AWG#14
x 2
AWG#14
x 2
f0 22"(5 6mm). . x4plcs
3.59" (91.2mm)
4.2" (106.8mm)
(--) Black
(+) Red
3.23"
(82.0mm)
2.61"
(66.4mm)
(+) Orange
(--) Black
HUNTINGTON BEACH, CA. USA
AWG#12
x 2
AWG#12
x 2
Ce manuel convient aux modèles suivants
1
Autres manuels NewMar Équipement d'enregistrement
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
