NEW MATTER Dragster Manuel utilisateur
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016 NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Dragster
Version 2.0
New Matter, 2016
Part number: 11070
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Hardware needed to complete this project:
Size Length Used Label
Screw, Type 25, Phillips Pan head, Thread Cutting #4-24 0.375” 14 A
Screw, Type 25, Phillips Pan head, Thread Cutting #6-20 0.375” 2 B
Screw, Type 25, Phillips Pan head, Thread Cutting #6-20 0.500” 2 C
Screw, Type 25, Phillips Pan head, Thread Cutting #6-20 0.750” 4 D
Rubberband, width 1/8” #33 3.500” 4
O-ring, width 1/8” #215 Ø1.300” 12
Nylon bearing (Unthreaded spacer w. ange) ID: 0.14”, OD: 0.17”
#6 0.250” 8
Drillbit (0.173”) #17 1
Suggestions on where to source the parts listed above:
www.fastnal.com, www.mcmaster.com, www.homedepot.com
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016 NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Ream the bore of the front
wheel with the drillbit. Ream
both front wheels.
Ream the bore of the rear
wheel with the drillbit. Ream
both rear wheels.
Ream the bore of the idler
gear with the drillbit. Ream
both idler gears.
1.0
2.0
3.0
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Ream the bore of the gear
spool with the drillbit. Ream
on both sides, do not drill
through the part.
Mount the ‘tires’ on the front
and rear wheels as shown in
step 5.0 through 5.7
Each wheel uses 3 o-rings.
Continue to assemble all
wheels.
4.0
5.0 5.4
5.1 5.5
5.2 5.6
5.3 5.7
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016 NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Insert a nylon bearing into
the rear wheel. Do this for
both rear wheels.
Insert a nylon bearing into
the front wheel. Do this for
both front wheels.
Insert a nylon bearing into
the idler gear. Do this for
both idler gears.
Insert two nylon bearings
into the gear spool, one on
each side.
6.0
7.0
8.0
9.0
6.1
7.1
8.1
9.1
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Install the idler gears onto
the gear beam. Use screw
labeled ‘C’. Make sure the
gears rotate freely.
Mount the gear beam to the
left side body peice using
one screw labeled ‘A’. Make
sure it rotates freely.
10.0
11.0
10.1
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016 NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Mount the other body piece
using one screw (‘A’). Make
sure the gearbeam moves
freely.
Install 2 screw (‘A’) into the
chassis as shown. These will
be used to adjust the center
distance of the gears. More
on that later.
12.0
13.0
13.1
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Attach the chassis to the up-
per assembly using 4 screws
(‘A’). 14.0
14.1
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016 NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Flip it over and mount the 2
spool beams using 4 screws
total (‘A’).
Note the slots in the beams.
They allow the gear cen-
ter distance to be tweaked.
More on that later.
15.0
15.1
NEW MATTER, DRAGSTER, 11070 VERSION 2.0, 2016
Attach the spool gear using
2 screws (‘B’). Check that it
rotates freely. 16.0
Attach the front rubberband
spool using 2 screws (‘A’). 17.0
16.1
17.1
