New Air APH-4000PV Manuel utilisateur

Owner’s manual

OUTDOOR PATIO HEATER

APH-4000PV

APH-4000SV

IMPORTANT

Your safety is very important, please read this manual thoroughly before you

install, operate and maintain this heater. Retain this manual for future reference.

If you have questions about assembly, operation, servicing or repair of this

heater, please contact your selling dealer or call us directly, we will gladly provide

assistance as required.

Warning For Outdoor Use Only!

Table of Contents

Important Warning……………………………………………………… …………2

Introduction………………………………………………………………………….

Specification………………………………………………………………………...

Important Safety Precautions…………………………………………….…… . -5

Assembly…………………………………………………………………………....5

Tools required………………………………………………………………………5

Unpacking…………………………………………………………..………………5

Component List………………………………………………..…………………...6

LP gas hook up and installation of the cylinder…………………………………6

Assembly Instructions……………………………………….

………………….

7-9

Installation………………………………………..…………………………….…...9

Operation……………………………………..………………………...……….…10

Preparation before lighting………………………….……………………….…..

Leak Checking……………………………………….……………………………10

Lighting…………………………………………..………….. .………………..10-11

Setting Control………………………………………...…………………………..

Turn Off and Re-light……………………....………………………………….….

Turn Off and Shut Down………………………..………………………….…….

….

Storage…………………………………………..……………………….….…11-12

Maintenance………………………………………………...…………………….

…

Troubleshooting………………………………………….………………….….…1

Service and Warranty Information………………………………………….…...14

Warranty Terms……………………………………………………...……………14

IMPORTANT WARNING

♦ Warning

For your safety

Fuels used in gas or oil-fired appliances and the products of combustion of such

fuels, contain chemicals known to the State of California to cause cancer, birth

defects and other reproductive harm. California Health & Safety Code Sec.25249.6

♦ Warning

For your safety

Improper installation, adjustment, alteration, service or maintenance can cause

injury or property damage from hazards of fire, explosion, burn, asphyxiation,

carbon monoxide poisoning. Please be sure you understand all operating the

instructions before operate or service this heater. Read this installation,

operation and maintenance instructions thoroughly before installing or servicing

this equipment.

♦ Warning

For your safety

Follow the correct lighting and usage procedures. Handle metal parts with care

to avoid injuries. Never allow children to operate this heater.

♦ Warning

For your safety

Do not store or use gasoline or other flammable vapors and liquids, solid combustibles

in the vicinity of this appliance. Keep a safe distance away from the heater as

recommended by the instructions.

♦ Warning

For your safety

If you smell gas:

1.Shut off gas to the appliance.

2.Extinguish any open flame near the appliance.

.If odor continues, immediately call your gas supplier or local fire department.

Introduction

Thank you for choosing Outdoor Patio Heater. Please

take the time to read these instructions and follow each step carefully for safe

operation. Retain this manual for future reference. If you have any question

regarding this instruction, please stop and feel free to contact your selling dealer

or call our Customer Service Dept. directly for assistance.

Specification

Model No

Type of Gas LPG (Propane) only

Input rating 40,000 BTU/HR

Pressure 11” W.C.

Gas Supply Inlet Pressure to

Regulator Max.150 PSI, Min. 5 PSI

Gas Cylinder

A Standard 20 IB. propane gas cylinder

with a Type 1 QCC adapter only (not

included) .

Overall Height 90 Inches

Reflector Diameter 4 Inches

Ignition System Piezo Igniter

Electrical connections No required

Net Weight 64 IBS. (not including the cylinder)

Important Safety Precautions

To ensure safe use of your outdoor patio heater, you are requested to pay

close attention to these essential safety requirements.



This is a propane, direct-fired heater. It Means that all of the combustion

products enter the heated space. Even though this heater operates very

close to 100 percent combustion efficiency, but it still produces small

amounts of carbon monoxide. Carbon monoxide (called CO) is toxic. CO

can build up in a heated space and failure to provide adequate ventilation

could result in death. So, Always be sure there is plenty of fresh air when

the heater is in use. Always follow advice about ventilation in these

operating instructions. If any time gas odor is detected, shot off the

appliance immediately, find and correct the leak. Please set up the propane

supply with utmost care.



Alert both children and elders to the hazard of high surface emperatures.

Care must be taken for the supervision of children in the vicinity of an

operating or hot heater.



Your children and pets should be supervised when they are in area of

heater.



This outdoor patio heater must be used for outdoors only in a well

ventilated area and not be used in a vehicle or any enclosed building.



Always place the heater on a level stable surface.



Do not move, touch the heater while hot or burning.



Do not alter or modify the heater in any manner



Use only a U.S. Department of Transportation approved 20 pound

standard cylinder equipped with an TYPE 1 connection with QCC

(Quick Connect Coupler).



Use only with propane / LP Gas. Do not attempt to use any other fuel.



Always keep at least a 24 ‘’ clearance from any combustible material.



Do not use if the wind velocity is greater than 10 miles/hr.



Do not use if the environment temperature is below 40 F.



Do not spray aerosols near the heater while in use.



Do not clean heater with combustible or corrosive cleaners. Use warm, soapy

water.



Do not hang clothing or flammable materials either on or near heater



Do not move, touch the heater while it is hot or in operation.



Place the control knob on OFF position when heater is not in use and always

disconnect the gas cylinder at its main valve and store it outdoors where it is

not accessible to children. Never store a propane cylinder indoors



Always 45 minutes to cool down after use before attempting to move your

heater.



Use only the hose and regulator with the heater provided by the factory. Check

the regulator and hose assembly before each use. If you find an excessive

abrasion or hose is cut, please replace with the Regulator assembly listed on

the parts list right away.



Never use the heater if the ballast weight is not assembled into the base. The

base must be weighted to prevent possible tipping.



Inspect heater before each use and inspect annually by a qualified service

person. Do not operate a damaged heater.



Leak check only with soapy water when the initial assembly and after every

cylinder is replaced. All gas connections should be checked. Look for bubbles.

Never use flame!

Warning

When the heater is to be operated in the presence of other people, the user is

instructions, and of the hazards involved. If this heater is used in a commercial or

rental installation, it is the responsibility of the purchaser to check with the local

codes for properly acquainting with the safety precautions and instructions.

Failure to comply with the precautions and instructions provided with this

heater can result in death, serious bodily injury and property loss or

damage from hazards of fire, explosion, burn, asphyxiation, carbon

monoxide poisoning. Be sure you understand all operation instructions

before attempting to operate or service this heater.

1. Assembly

Note The assembly of this heater requires basic mechanical skills. Proper

assembly is the responsibility of the installer. All service and repair should

be done by a qualified person.

1.1

Tools required

8mm, 10mm, 11mm, 12mm Socket

#2 & # Phillips Head Screwdriver

Pliers or Channel Lock Pliers

Crescent or Open End Wrenches

Caution

Do not use Teflon Tape or any thread sealing compounds where connections

between heater head to Fuel-Tube and Regulator / Hose assembly to Fuel-

Tube.

1.2 Unpacking



Remove the Fuel-tube, the Post and Heater burner assembly from the

Box 2 of 2.



Take out the heater burner assembly from the base assembly by removing the

three Hex-Nuts, Flat washers and Lock washers, then screw the nuts and

washers back onto the bolts at the top of the burner assembly.



Remove all shipping packaging foam on the components.



Check the fasteners, Regulator assembly and the Owner’s Manual provided

by the factory.



Remove the Reflector from the Box 1 of 2.



Check the heater for any shipping damage, if any is found, immediately

contact and return this heater to the dealer or distributor where purchased.



Retain all packaging material and carton until heater warranty has expired.

Any warranty returns require original packing and carton.

1.3 Component List

(see Figure 1)



Reflector



Burner assembly



Base assembly with the



allast weight & Bracket





uel -line



Cylinder decorative cover



Post / the Slip socket cover



Regulator / hose assembly



Fastener package



Owner’s manual



Wheel Kit (optional part)

(

Figure 1)

1.4 LP gas hook up and

installation of the cylinde

1.4.1 Gas requirements:



Our heater is designed to use LP gas only, never substitute gases.





he heater comes with a regulator/hose assembly for hook up to a standard

20 pound (5 gallon) LP Overfill Protection Device and Type 1 fitting equipped

gas cylinder. The LP cylinder is not included. You need to purchase a filled

LP Cylinder that must be constructed and marked in accordance with

specifications of the U.S. Department of Transportation. Do not use dented or

rusty LP cylinder by your LP supplier.



Never use an LP cylinder with a damaged valve.



Do not modify the Regulator / hose assembly.

1.4.2 LP gas hook up (see Figure 2)

The heater is designed to house a 20 pound gas

cylinder on the base assembly.



Lift the cylinder decorative cover and

rest it on the triangular Socket.



Place the LP cylinder into the housing

on the Base, then attach the Regulator

/ hose assembly to the LP cylinder

valve. The regulator and the Cylinder

have right-handed threads (clockwise to

tighten).

Be sure this connection is tight but do

not over tighten on the LP cylinder valve. (Figure 2)

1.5 Assembly Instructions

Step 1

. Set the burner assembly on a flat

surface. Remove the protective end cap

from the only one end of the male flared

fitting at the end of the fuel line. Leave

the other end cap on to protect the fitting

while you are doing this assembly. Screw

the male flared fitting into the inlet fitting

at the base of the burner head and tighten

using a ¾ wrench. Be sure that the

connection is tight (do not over-tighten).

See Figure 3

(Figure 3)

Note The connection between the fuel line and the burner inlet fitting is brass-to

brass connection. This connection doesn’t require any thread sealing

compounds. The flare design of the threads provides a gas tight seal.

Step 2.

Carefully slide the post

(Note:

the Slip socket cover

has been assembled to the

post) over the fuel line. The post

fit one way only because the

holes drilled different positions.

The end of the post that connects

to the burner head has four

holes drilled about ½” below

the top of the post. That other

end of the post that will connect

to the support socket has four

holes drilled about 11/2” from

the other end of the post. Attach

the post to the burner assembly

using four Pan Head (Phillips) screws,

Flat washers and Lock washers. Make

sure that the setscrews firmly grip the

post. See Figure 4. (Figure 4)

Step 3.

If you prefer the heater

comes with the wheel kit, you

need to purchase them from your

selling dealer. You can attach

the wheel kit with the

fasteners provided now.

See Figure 5.

Step 4.

Place the cylinder

decorative cover over the

base assembly / brackets.

(

(Figure 5)

Step 5.

Please carefully insert the

Post/Slip Socket Cover assembly

with the fuel line into the post support

socket assembly. Be sure that the lower

end of the fuel line passes through the

hole in the post support plate. Using

four Pan Head (Phillips) screws, Flat

washers secure the post / the slip socket

cover into the post support socket. (Do

not use lock washers at this connection).

Make sure the setscrews through the

Post and the slip socket cover firmly

grip the post. See Figure 6

(

(Figure 6)

Step 6.

Carefully lift up the cylinder

decorative cover. Tilt the cylinder

decorative cover and rest it on the

post support Socket by against the

Hex-bolts. Make sure that the

cylinder decorative cover is in a

stable position. Never allow it slides!

See Figure 7

Step 7.

Remove the other protective end cap

from the fuel line inlet fitting. Hold the fuel line

inlet fitting with an ¾ wrench and gently hand-

tighten the female fitting at the hose & regulator

assembly to the fuel line inlet fitting, then securely

tighten with another ¾” wrench. These fittings

should be tightened in a clockwise direction.

Do no over-tighten.

See Figure 7. (Figure 7)

Step 8.

Connect an approved propane cylinder to regulator / hose assembly.

Properly tighten the regulator’s hand wheel and connection device to tank

valve. o not use tools.

First check for leaks

Be sure the fittings at the end of the feed line going into the burner head and

other end of the fuel feed line where the hose is attached are tight.

Leak test with a soapy solution by mixing one part liquid soap solution with two

parts water only. Do not use flame!

1. Turn the Control Knob to the “OFF” position. Open the LP cylinder valve.

2. Apply a soapy solution to these connections. Bubbles will form if the

connection is leaking. You will need to reconnect and leak test again. Upon

completion of the leak test, turn off the LP cylinder valve and disconnect and

remove the cylinder. Go to the next step.

Step 9.

Tilt the heater over to a proper

position (or using one of the shipping

Styrofoam inserts to prop up the top half

of the heater). Secure the reflector

onto Emitter by using the three Hex-

Nuts, Flat washers and Lock washers.

Make sure that the nuts are tight properly.

Stand the heater upright. As shown in

Figure 8. (Figure 8)

Step 10.

The cylinder Must be secured in the base and chained in the upright position to

keep it from falling or being knocked over.

2. Installation

This heater is intended for use outdoors only! Don’t be used on any moving

objects and any enclosed areas!

2.1 Installation warning

The installation must conform with local, state and federal codes. In

absents of such codes, install in accordance with the current American

National Standard (ANSI) / National Fire Protection Association (NFPA)

publication “ Standard for the Storage and Handling of Liquefied Petroleum

Gases” ANSI / NFPA 58-Latest Revision, and “ National Fuel Gas Code”

ANSOZ22 .1.

2.2 Minimum clearances

Minimum 24” clearances from combustible materials must be maintained at

all times while the heater is in operation.

3. Operation

3.1 Preparation before lighting

.1.1 Check any possible shipping damage of the heater. If any is found,

immediately contact your selling dealer or call us directly.

.1.2 Please review thoroughly and be sure you understand all of the “safety

precautions and warnings”.

.1. Make sure control knob is at “OFF” position.

.1.4 Place the LP cylinder onto the Cylinder Base. Connect the Regulator /

hose assembly to the cylinder by rotating the Regulator’s hand wheel

clockwise into the cylinder’s valve and securely tighten.

.1.5 If attempting to relight a hot heater, always wait until the heater is cool.

3.2 Leak Checking



Check all of gas connections in the heater with soapy water.



Apply soap solution to all propane connections, especially the fuel connections

between the Regulator connection device to the Cylinder valve, the fitting at

the end of the Fuel Line to the Burner Head and the other end of the Fuel Line

to the Hose assembly.



Inspect all propane connections, look for bubbles.



If bubbles appear, there is a leak. Disconnect and reconnect, try again.



If no bubbles appear, the connection is safe, continue the next step: Lighting.



If the leak persists, turn cylinder valve OFF and contact your selling

dealer or

call our Customer Service Dept. directly for assistance

and advice.

Warning



Perform Leak test outdoors only.



Never leak test when smoking.



Do not use a flame to check for leaks.

3.3 Lighting

3.3.1 To light the pilot



Lift the cylinder cover from the base and set it the stable position. Turn the

cylinder valve on.



The first step is to purge the fuel line when a new or refilled propane cylinder is

installed.



Gently depress the control knob at the faceplate panel and rotate it to “PILOT”

Autres manuels pour APH-4000PV

Ce manuel convient aux modèles suivants

Autres manuels New Air Chauffage de terrasse

New Air

New Air APH-4000PV Manuel utilisateur

Manuels Chauffage de terrasse populaires d'autres marques

empasa

empasa HMXD-E-NHS Manuel utilisateur

Sunred

Sunred Indus Manuel utilisateur

HEAT1

HEAT1 ECO pro-line 2300W Manuel utilisateur

Heatmaxx

Heatmaxx SRPH98 Manuel utilisateur

Sunjoy

Sunjoy A30600640 Manuel utilisateur

Event Furniture

Event Furniture 16091 Guide de dépannage

Prem-I-Air

Prem-I-Air EH1462 Manuel utilisateur

Blumfeldt

Blumfeldt 10028637 Manuel utilisateur

Sunjoy

Sunjoy L-PH011PSS-2 Manuel utilisateur

Melissa

Melissa 670-202 Manuel utilisateur

Quality Heating

Quality Heating THE-12DW Manuel utilisateur

DCS

DCS PHFS-P4 Guide d'installation

EUROM

EUROM 334241 Manuel utilisateur

Lava Heat

Lava Heat Venetian Manuel utilisateur

EHS Ltd.

EHS Ltd. HQH-2000W Manuel utilisateur

VONROC

VONROC ALICUDI PH515AC Manuel utilisateur

OZONA

OZONA Heatflow IF010997 Manuel d'exploitation et d'entretien

theBBQshop

theBBQshop 51611010 Guide de configuration