Neue IDSH604W Manuel utilisateur
IDSH604W
User Manual
EN
Dishwasher
Contents
Safety information 2
Safety instructions 3
Product description 4
Control panel 5
Programmes 5
Settings 6
Before first use 8
Daily use 9
Hints and tips 10
Care and cleaning 11
Troubleshooting 13
Technical information 15
GREAT BRITAIN – Customer Care and Service 16
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the supplied
instructions. The manufacturer is not responsible for any injuries or damages
that are the result of incorrect installation or usage. Always keep the
instructions in a safe and accessible location for future reference.
Children and vulnerable people safety
•This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a safe way and
understand the hazards involved.
•Do not let children play with the appliance.
•Keep detergents away from children.
•Keep children and pets away from the appliance when the door is open.
•Children shall not carry out cleaning and user maintenance of the
appliance without supervision.
General Safety
•This appliance is intended to be used in household and similar
applications such as:
–farm houses; staff kitchen areas in shops, offices and other working
environments;
–by clients in hotels, motels, bed & breakfast and other residential type
environments.
•Do not change the specification of this appliance.
•The operating water pressure (minimum and maximum) must be between
0.5 (0.05) / 8 (0.8) bar (MPa)
2
•Obey the maximum number of 13 place settings.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
Authorised Service Centre or similarly qualified persons in order to avoid a
hazard.
•Put the cutlery in the cutlery basket with the sharp ends pointing down or
put them in the cutlery drawer in a horizontal position with the sharp edges
down.
•Do not leave the appliance with the open door unattended to avoid
stepping accidentally onto it.
•Before any maintenance operation, deactivate the appliance and
disconnect the mains plug from the socket.
•Do not use high pressure water sprays and/or steam to clean the
appliance.
•If the appliance has ventilation openings in the base, they must not be
covered e.g. by a carpet.
•The appliance is to be connected to the water mains using the new
supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
Warning! Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C.
• Follow the installation instruction supplied with the
appliance.
• Always take care when moving the appliance as it is
heavy. Always use safety gloves and enclosed
footwear.
• Make sure that the appliance is installed below and
adjacent to safe structures.
Electrical connection
Warning! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the parameters on the rating plate
are compatible with the electrical ratings of the
mains power supply.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains plug
and to the mains cable. Should the mains cable
need to be replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains socket only at
the end of the installation. Make sure that there is
access to the mains plug after the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.
• Only for UK and Ireland. The appliance has a 13
amp mains plug. If it is necessary to change the
fuse in the mains plug, use fuse: 13 amp ASTA (BS
1362).
Water connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used for
a long time, where repair work has been carried out
or new devices fitted (water meters, etc.), let the
water flow until it is clean and clear.
• Ensure that there are no visible water leaks during
and after the first use of the appliance.
• If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains plug
3
from the mains socket. Contact the Authorised
Service Centre to replace the water inlet hose.
Use
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous. Obey the
safety instructions on the detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance until
the programme is complete. Some detergent may
remain on the dishes.
• The appliance can release hot steam if you open the
door while a programme operates.
• Do not put flammable products or items that are wet
with flammable products in, near or on the
appliance.
Service
• Contact the Authorised Service Centre to repair the
appliance. We recommend only the use of original
spare parts.
• When you contact the Authorised Service Centre,
ensure that you have the following information that
is available on the rating plate.
Model :
PNC :
Serial Number :
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets
to get closed in the appliance.
Product description
43
7
9 8
10 56
11
12
1Upper spray arm
2Lower spray arm
3Filters
4Rating plate
5Salt container
6Air vent
7Rinse aid dispenser
8Detergent dispenser
9Cutlery basket
10 Lower basket
4
11 Upper basket
Control panel
4
3
2
1
1On/off button
2Programme indicators
3Indicators
4Programme button
Indicators
Indicator Description
End indicator.
Salt indicator. It is always off while the programme operates.
Programmes
Programme Degree of soil
Type of load
Programme phases Consumption values
1)
Duration
(min)
Energy
(kWh)
Water
(l)
2) Normal soil
Crockery and cut-
lery
• Prewash
• Wash 50 °C
• Rinses
• Dry
227 1.039 11
Heavy soil
Crockery, cutlery,
pots and pans
• Prewash
• Wash 70 °C
• Rinses
• Dry
155 - 170 1.5 - 1.7 14-15
Normal soil
Crockery and cut-
lery
• Prewash
• Wash 65 °C
• Rinses
• Dry
130 - 140 1.4 - 1.6 15-17
5
Programme Degree of soil
Type of load
Programme phases Consumption values
1)
Duration
(min)
Energy
(kWh)
Water
(l)
3) Fresh soil
Crockery and cut-
lery
• Wash 60 °C or
65 °C
• Rinses
30 0.8 10
4) All • Prewash 14 0.1 5
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes
can change the values.
2) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with nor-
mal soil. (This is the standard programme for test institutes).
3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
4) Use this programme to quickly rinse the dishes. this prevents the remaining food to bond on the dishes and bad odours to
come out from the appliance. Do not use detergent with this programme.
Information for test institutes
For all the necessary information for test performance,
send an email to:
Write down the product number (PNC) that is on the
rating plate.
Settings
Programme selection mode and user mode
When the appliance is in programme selection mode it
is possible to set a programme and to enter the user
mode.
Settings available in the user mode:
• The level of water softener according to the water
hardness.
• Activation or deactivation of the acoustic signal for
the end of a programme.
• Activation or deactivation of AirDry.
As the appliance stores the saved settings, there is
no need to configure it before every cycle.
How to set the programme selection mode
The appliance is in programme selection mode when
the programme indicator flashes.
After activation, the appliance is in programme selection
mode by default. If not, set the programme selection
mode the following way:
Press and hold the programme button until the
appliance is in programme selection mode.
The water softener
The water softener removes minerals from the water
supply, which would have a detrimental effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in equivalent
scales.
The water softener should be adjusted according to the
hardness of the water in your area. Your local water
authority can advise you on the hardness of the water in
your area. It is important to set the right level of the
water softener to assure good washing results.
6
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l Clarke de-
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5 1 2)
1) Factory setting.
2) Do not use salt at this level.
Whether you use a standard detergent or multi-tabs
(with or without salt), set the proper water hardness
level to keep the salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
How to set the water softener level
The appliance must be in programme selection mode.
1. To enter the user mode, press and hold the
programme button until the indicator
flashes and the indicators and are on.
2. Wait until the indicators and are off and
the indicator flashes. The indicator
still flashes. The intermittent flashing of the
indicator shows the current setting.
• e.g. 5 flashes + pause + 5 flashes = level 5.
3. Press programme button repeatedly to change the
setting. Each pressing of the programme button
increases the level number. After reaching level 10,
the count starts again from level 1.
4. Press the on/off button to confirm the setting.
Acoustic signals
Acoustic signals sound when a malfunction of the
appliance occurs. It is not possible to deactivate these
acoustic signals.
There is also an acoustic signal that sounds when the
programme is completed. By default this acoustic signal
is deactivated but it is possible to activate it.
How to activate the acoustic signal for the end of
programme
The appliance must be in programme selection mode.
1. To enter the user mode, press and hold the
programme button until the indicator
flashes and indicators and are on.
2. Press the programme button immediately.
• The indicator and are on.
• The indicator flashes.
3. Wait until the indicator and are off. The
indicator still flashes.
• The indicator shows the current setting:
off = Acoustic signal off.
4. Press the programme button to change the setting.
• on = Acoustic signal on.
5. Press on/off confirm the setting.
AirDry
AirDry improves the drying results with less energy
consumption.
7
During the drying phase, the door opens
automatically and remains ajar.
Caution! Do not try to close the
appliance door within 2 minutes after
automatic opening. This can cause
damage to the appliance.
AirDry is automatically activated with all programmes
excluding .
Caution! If children have access to the
appliance, it is advised to deactivate
AirDry as opening the door may pose a
danger.
How to deactivate AirDry
The appliance must be in programme selection mode.
1. To enter the user mode, press and hold the
programme button until the indicator
flashes and indicators and are on.
2. Press the programme button twice.
• The indicators and are on.
• The indicator flashes.
3. Wait until the indicators and are off.
The indicator still flashes.
• The indicator shows the current setting:
off = AirDry is deactivated.
4. Press the programme button to change the setting.
• on = AirDry is activated .
5. Press on/off to confirm the setting.
Before first use
1. Make sure that the current level of the water
softener agrees with the hardness of the water
supply. If not, adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance. Do
not use detergent and do not load the baskets.
After starting a programme, it may take up to 5 minutes
for the appliance to recharge the resin in the water
softener. It seems that the appliance is not working. The
washing phase starts only after this procedure is
completed. The procedure is repeated periodically.
The salt container
Caution! Use rough salt designed for
dishwashers only. Fine salt increases the
risk of corrosion.
The salt is used to recharge the resin in the water
softener and to assure good washing results in daily
use.
How to fill the salt container
1. Turn the cap of the salt container counterclockwise
and remove it.
2. Put 1 litre of water in the salt container (Only for the
first time).
3. Fill the salt container with dishwasher salt.
4. Remove the salt around the opening of the salt
container.
8
5. Turn the cap of the salt container clockwise to
close the salt container.
Caution! Water and salt can come out of
the salt container when you fill it. After
you fill the salt container, immediately
start a programme to prevent corrosion.
How to fill the rinse aid dispenser
M
A
X
1
2
3
4
+
-
AB
D
C
E
Caution! Only use rinse aid specifically
designed for dishwashers.
1. Press the release button (D) to open the lid (C).
2. Pour the rinse aid in the dispenser (A) until the
liquid reaches the fill level 'max'.
3. Remove the spilled rinse aid with an absorbent
cloth to prevent too much foam.
4. Close the lid. Make sure that the release button
locks into position.
Fill the rinse aid dispenser when the
indicator (E) becomes clear.
You can turn the selector of the released
quantity (B) between position 1 (lowest
quantity) and position 4 or 6 (highest
quantity).
Daily use
1. Open the water tap.
2. Press the on/off button to activate the appliance.
Make sure that the appliance is in programme selection
mode.
• If the salt indicator is on, fill the salt container.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the type of
load and the degree of soil.
Using the detergent
20
30
BA D
C
1. Press the release button (B) to open the lid (C).
2. Put the detergent, in powder or tablets, in the
compartment (A).
3. If the programme has a prewash phase, put a small
quantity of detergent in the compartment (D).
4. Close the lid. Make sure that the release button
locks into position.
9
Using the multi-tablets
When you use tablets, that contain salt and rinse aid, do
not fill the salt container and the rinse aid dispenser.
1. Adjust the water softener to the lowest level.
2. Set the rinse aid dispenser to the lowest position.
Setting and starting a programme
Standby mode
The standby mode decreases energy consumption by
automatically deactivating the appliance when it is not
operating.
The mode activates:
• 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate the appliance.
Make sure that the appliance is in programme
selection mode.
3. Press the programme button repeatedly until the
indicator of the programme you want to select
starts flashing.
4. Close the appliance door to start the programme.
Opening the door while the appliance operates
Opening the door while a programme is running stops
the appliance. It may affect the energy consumption and
the programme duration. After closing the door, the
appliance continues from the point of interruption.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
Do not try to close the appliance door
within 2 minutes after AirDry
automatically opens it, as this may cause
damage to the appliance.
If, afterwards, the door is closed for
another 3 minutes, the running
programme ends.
Cancelling the programme
Press and hold the programme button until the
appliance is in programme selection mode.
Make sure that there is detergent in the detergent
dispenser before you start a new programme.
End of the programme
When the programme is completed the indicator is
on.
1. Press the on/off button or wait for the appliance to
switch to standby mode. If you open the door
before the activation of standby mode, the
appliance is automatically deactivated.
2. Close the water tap.
Hints and tips
General
The following hints will ensure optimal cleaning and
drying results in daily use and also help to protect the
environment.
• Remove larger residues of food from the dishes into
the waste bin.
• Do not pre-rinse dishes by hand. When needed, use
the prewash programme (if available) or select a
programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the
dishes can be completely reached and washed by
the water released from the spray arm nozzles.
Make sure that items do not touch or cover each
other.
• You can use dishwasher detergent, rinse aid and
salt separately or you can use the multi-tablets (e.g.
''3in1'', ''4in1'', ''All in 1''). Follow the instructions
written on the packaging.
• Select the programme according to the type of load
and degree of soil. With the ECO programme you
have the most efficient use of water and energy
consumption for crockery and cutlery with normal
soil.
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause damage to
the appliance.
• In areas with hard and very hard water we
recommend to use plain dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
• At least once a month run the appliance with the use
of appliance cleaner which is particularly suitable for
this purpose.
10
Table des matières
Autres manuels Neue Lave-vaisselle
