Network Technologies XTENDEX Series Manuel utilisateur

MAN063 Rev Date 10/4/2006

ST-C5DVI-150

150 FOOT DVI VIDEO EXTENDER

Installation and Operation Manual

Software Version 1.2

XTENDEXTM Series

NETWORK

TECHNOLOGIES

INCORPORATED

Tel:330-562-7070

Fax:330-562-1999

1275 Danner Dr

Aurora, OH 44202

www.networktechinc.com

NTI R

TRADEMARK

EXTENDEX is a trademark of Network Technologies Inc in the U.S. and other countries.

retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

TABLE OF CONTENTS

Introduction......................................................................................................................................................................1

Materials..........................................................................................................................................................................1

Features and Functions...................................................................................................................................................2

Limitations .......................................................................................................................................................................3

Preparation for Installation ..............................................................................................................................................3

Installation .......................................................................................................................................................................4

Installing The Remote Unit ..........................................................................................................................................4

Connect the CAT5e cables..........................................................................................................................................4

Installing The Local Unit ..............................................................................................................................................5

Connect The CAT5e/6 Cables.....................................................................................................................................5

Plug-in and Boot Up.....................................................................................................................................................6

DDC Data Configuration..................................................................................................................................................6

Technical Specifications..................................................................................................................................................7

Interconnection Cable Wiring Method.............................................................................................................................7

Troubleshooting...............................................................................................................................................................8

Warranty Information.......................................................................................................................................................8

TABLE OF FIGURES

Figure 1- Connect the Extended Components to the Remote Unit....................................................................................................4

Figure 2- Connect the CAT5e cable to the Remote Unit....................................................................................................................4

Figure 3- Connect the XTENDEX Local Unit to the source and local user.........................................................................................5

Figure 4- Connect CAT5 cable to Local Unit......................................................................................................................................5

Figure 5- Connect the AC adapter to the Local Unit ..........................................................................................................................6

Figure 6- Configure the XTENDEX for Local Monitor DDC Data Transfer.........................................................................................6

Figure 7- View looking into RJ45 female............................................................................................................................................7

NTI XTENDEX DVI Video Extender

INTRODUCTION

The XTENDEX Series CAT5 DVI Video Extender (XTENDEX) is designed to enable the video output from one digital video

source to be viewed by two users, one local and one remote. The remote monitor can be located as much as 150 feet away

from a CPU via Category 5/5e/ or 6 (CAT5) twisted-pair cable. The local user monitor will be located near the video source CPU.

The XTENDEX Series Extender is extremely simple to install and has been thoroughly tested to insure reliable performance.

Through the use of CAT5 cable it is possible to economically increase the flexibility of a computer system. Here are some of the

features and ways this can benefit any workplace:

•Allows the placement of a DVI-enabled monitor in a location where only these parts are needed without having the video

source there too, taking up valuable space

•Allows DVI video to be viewed by both a local and remote user (up to 150 feet away)

•Provides crisp and clear resolution up to 1920 x 1200 @ 100 feet (see page 7 for more details)

•Video quality, for varying lengths of cable, is automatically adjustable providing optimum image quality

•Transmits single link DVI-D signal over two CAT5 cables.

•Built-in surge protection.

•Only one power supply is necessary to power both the Local and Remote units.

•Supports local and remote DVI monitors.

•Compatible with DDWG DVI standard.

•HDCP Compliant

•Supports the DDC2B protocol.

MATERIALS

Materials Included with this kit:

9NTI XTENDEX Local Unit

9NTI XTENDEX Remote Unit

9DVI-D-MM-S-2M 2 meter male-male DVI video cable

9120VAC or 240VAC at 50 or 60Hz-5VDC/2.0A AC Adapter

9This owner's manual

Additional materials may be required but are not supplied:

¾CAT5 unshielded twisted-pair cables terminated with RJ45 connectors wired straight thru- pin 1 to pin 1, etc. (see pg. 8 for

proper EIA/TIA 568 B wiring method)

¾DVI male-male cables to connect the monitor(s) to the Remote and Local units (Order NTI # DVI-IS-xx-MM where x=3, 6, or

10 foot cable). Both DVI-I and DVI-D type cables can be used for this connection.

Contact your nearest NTI distributor or NTI directly for all of your KVM needs at 800-RGB-TECH (800-742-8324) in US & Canada

or 330-562-7070 (Worldwide) or at our website at http://www.networktechinc.com and we will be happy to be of assistance.

NTI XTENDEX DVI Video Extender

FEATURES AND FUNCTIONS

1. Yellow LED- illuminates when video input is available and starts blinking when the input is synchronized

2. DDC/Pwr - RJ45 connector- for connecting the CAT5 cable between the Local and Remote units to carry DDC data from the

remote video display and to carry power to the Remote unit.

3. Green LED- power indicator- illuminates when power has been supplied to the unit

4. 5VDC- 2.0A- connection jack for the AC adapter

5. Dipswitches- for configuring the DDC source to be either the local or remote video display device

6. Video- RJ45 connector- for connecting the CAT5 cable to carry the video signal between the Local and Remote units

7. Video In- DVI female video connector- for connecting a video cable between the Local Unit and the video source

8. Video Out- DVI female video connector- for connecting the local user's DVI display device

9. Video Out- DVI female video connector- for connecting the remote user's DVI display device

ST-C5DVI-150 Local Unit

(Front View) (Rear View)

ST-C5DVI-150 Remote Unit

(Front View) (Rear View)

NTI R

Netw ork Tech nologies Inc

XTENDEX

45 6 8

6 9

NTI R

Network Technologies Inc

XTENDEX

NTI R

Netwo rk Technolo gies Inc

XTENDEX

NTI R

Netw ork Tech nologies Inc

XTENDEX

NTI XTENDEX DVI Video Extender

LIMITATIONS

•Hot-plugging of monitors is supported provided monitors were originally connected at power-up.

•CAT5 shielded cables are not recommended for use with this extender.

PREPARATION FOR INSTALLATION

•Locations should be chosen for the monitors that also have space to connect the Remote and Local units within the distance

provided by the cables. If extension cables are needed, contact NTI for the cables required.

•The CAT5 cables must be run to the locations where the Remote and Local units will be connected. Be careful to route the

cables away from any sources of magnetic fields or electrical interference that might reduce the quality of the video signal

(i.e. AC motors, welding equipment, fluorescent lighting, etc.).

•All cables should be installed in such a way that they do not cause stress on their connections to the equipment. Extended

lengths of cable hanging from a connection may interfere with the quality of that connection. Secure cables as needed to

minimize this.

•Properly shut down and disconnect the power from the video source and monitors to be separated. If other equipment is

involved whose connections are being interrupted, be sure to refer to the instruction manuals for that equipment for proper

disconnection and re-connection procedures before proceeding.

Digital

Multi-Scan

Monitor

Local User

Digital

Multi-Scan

Monitor

Remote User

Up to 150 Feet

CAT5 Cable

Local

Unit Remote

Unit

ST-C5DVI-150 ST-C5DVI-150

DVI-D-MM-S-2M

Cable

DVI-IS-xx-MM

Cable

TYPICAL APPLICATION

adapter

(supplied)

Digital Video

Source CAT5 Cable

DVI-IS-xx-MM

Cable

NTI XTENDEX DVI Video Extender

ST-C5DVI-150 Remote Unit

(Front View)

CAT5 Cable to

Local Unit

"Video"

CAT5 Cable to

Local Unit

"DDC/Pwr"

NTI R

Netw ork Tech nologies Inc

XTENDEX

INSTALLATION

Installing The Remote Unit

1. Position the Remote Unit such that the CAT5 cable and the monitor cables can each reach the Remote Unit without

putting strain on the cables.

2. Connect the monitor cable to the female DVI video connector labeled "Video Out" on the Remote Unit.

Figure 1- Connect the extended video display to the Remote Unit

Connect the CAT5 cables

Make sure the CAT5 cables (two required) have been installed in accordance with the

“Preparation for Installation” instructions on page 3. Connect the CAT5 cables to

the “Cat5” ports on the Remote Unit. (See Fig. 2.) When properly inserted the

CAT5 cable ends should snap into place.

Note: The two cables must be connected to like ports at each end of

the cables. I.e. It is important that one cable is connected between the

"VIDEO" port at the Remote Unit and the same port at the Local Unit.

The other CAT5 cable must connected between the "DDC/PWR" ports of the

Remote and Local Units. Powering the units with the cables crossed

may damage them.

WARNING: Never connect the XTENDEX to an

Ethernet card, Ethernet router, hub or switch or other

Ethernet RJ45 connector of an Ethernet device. Damage to

devices connected to the Ethernet may result.

Figure 2- Connect the CAT5 cable to the Remote Unit

Digital

Multi-Scan

Monitor

(Rear View)

DVI-IS-xx-MM

Remote User Display

ST-C5DVI-150 Remote Unit

NTI R

Netw ork Tech nologies Inc

XTENDEX

NTI XTENDEX DVI Video Extender

Front View of Local Unit

CAT5 Cable to

Remote Unit

"DDC/Pwr"

CAT5 Cable to

Remote Unit

"Video"

NTI R

Network Technologies Inc

XTENDEX

Installing The Local Unit

1. Make connections for a local user (optional). Connect the cable from the local user's DVI monitor to the female

DVI "Video Out" port on the Local Unit.

2. Connect the DVI-D-MM-S-2M cable between the video source and the "Video In" connector on the Local Unit.

Figure 3- Connect the XTENDEX Local Unit to the source and local video display

Connect the CAT5 Cables

Connect the CAT5 cables to the “Cat5” ports on the Local Unit. (See Fig. 4.)

When properly inserted the cable ends should snap into place. Be sure to connect

the cable from the Remote Unit "Video Cat5" port to the "Video Cat5" port on the

Local Unit and to connect the cable from the Remote Unit "DDC/PWR" port to

the "DDC/PWR" port on the Local Unit. DO NOT get them mixed up or damage

to the unit may occur.

Note: The two cables must be connected to like ports at each end of the

cables. Powering the unit with the cables crossed may damage it.

WARNING: Never connect the XTENDEX to an Ethernet card,

Ethernet router, hub or switch or other Ethernet RJ45 connector of an

Ethernet device. Damage to devices connected to the Ethernet may

result.

Figure 4- Connect CAT5 cable to Local Unit

Rear View of Local Unit

DVI-D-MM-S-2M

Mating Face of

DVI-I Male

Digital Video Source

Mating Face of

DVI-I Female

Digital Video

Multi-Scan

Monitor

(supplied)

Local User Video Display

(Rear View)

NTI R

Netwo rk Techn ologies I nc

XTENDEX

DVI-IS-xx-MM

NTI XTENDEX DVI Video Extender

5 VDC

ADAPTER Barrel

(Inside

barrel)

(Outside

barrel)

Power Connector

2.1 mm x 5.5 mm Female

5VDC @ 2.0A OUTPUT

Front View of Local Unit

Yellow LED

Plug-in and Boot Up

1. Plug the power cord from the monitor into the power outlet.

2. Connect the AC adapter power connector to the 5VDC port on the Local Unit. Plug the AC adapter into a power outlet. The

green Power LED on the RJ45 connector of both the Remote and Local Units should illuminate, indicating that a proper

power connection has been made to them. (See Fig. 5.)

3. Turn ON the CPU and Monitors.

They should each react as if they

were directly connected to each other.

Note: The yellow LED on each RJ45

connector will illuminate when input video is

available and starts blinking when the video

is synchronized. (See Fig. 5)

Figure 5- Connect the AC adapter to the Local Unit

DDC DATA CONFIGURATION

By default, the XTENDEX is configured to transfer DDC data to the CPU (when the video source is a CPU) from the monitor

connected to the Remote Unit through the CAT5e cable attached to the "DDC/Pwr" port. In order for the CPU to receive this

data, the monitor connected to the Remote Unit must be powered ON before the CPU is powered ON.

Alternatively, the XTENDEX can be configured to transfer the DDC data from the monitor attached to the Local Unit. Follow

these steps to configure the XTENDEX:

1. Power OFF the CPU and monitors

2. Move the #1 slide switch on the front of the Local Unit up to "ON" (see Fig. 6 ).

3. Power ON the monitor connected to the Local Unit

4. Power ON the CPU.

FYI: The position of the #2 slide switch does not matter. It is not used.

Figure 6- Configure the XTENDEX for Local Monitor DDC Data Transfer

For Local

DDC data

spare

For Remote

DDC data

spare

NTI XTENDEX DVI Video Extender

TECHNICAL SPECIFICATIONS

Video

Video Compatibility PC Resolution up to 1920x1200 @60Hz / HDTV resolution up to 1080P

Video Connectors DVI-I Female

Input / Output Impedance 100 ohm differential

Digital Video data rate 1.65 Gbits

DVI Single Link Range 1920 x 1200

Video Maximum I/O Levels 1.2Vp-p

General

Interconnect Cable CAT5/5e/6 Solid UTP EIA/TIA 568 B wiring w/ male RJ45 connectors

Operating Temperature 0-40º C

Local Unit Power 120V or 240V at 50 or 60Hz-5VDC/2.0A via AC Adapter

Remote Unit Power powered by Local Unit through CAT5 cable

Local Current Consumption 700mA (max.)

Remote Current Consumption 700mA (max.)

Enclosure type Electro-galvanized steel black powder coated

Size (In.) WxDxH 3.5x3.1x1.1

Distances and Resolutions for CAT5,CAT5e and CAT6 Cables

Unshielded Twisted Pair (UTP) Resolutions

STP CABLE DISTANCE (feet) RESOLUTION

CAT5/5e 150 1024x768 at 60Hz

CAT5/5e 125 1280x1024 at 60Hz

CAT5/5e 100 1920x1200 at 60Hz

CAT6 150 1280x1024 at 60Hz

CAT6 125 1600x1200 at 60Hz

CAT6 100 1920x1200 at 60Hz

INTERCONNECTION CABLE WIRING METHOD

The CAT5 connection cables between the remote and local are terminated with RJ45 connectors and must be wired according to

the EIA/TIA 568 B industry standard. Wiring is as per the table and drawing below.

Pin Wire Color Pair Function

1 White/Orange 2 T

2 Orange 2 R

3 White/Green 3 T

4 Blue 1 R

5 White/Blue 1 T

6 Green 3 R

7 White/Brown 4 T

8 Brown 4 R

Figure 7- View looking into RJ45 female

Pair 2 Pair 1 Pair 4

Pair 3

Autres manuels pour XTENDEX Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Network Technologies Extenseur

Network Technologies

Network Technologies XTENDEX ST-C6USBH-300 Manuel utilisateur

Network Technologies

Network Technologies ST-C5USBV-300M Manuel utilisateur

Network Technologies

Network Technologies XTENDEX ST-C5V-600 Manuel utilisateur

Network Technologies

Network Technologies ST-C5KVM2ARS-1000S Manuel utilisateur

Network Technologies

Network Technologies XTENDEX ST-C5VA-WL500 Manuel utilisateur

Network Technologies

Network Technologies XTENDEX Series Manuel utilisateur

Network Technologies

Network Technologies XTENDEX Series Manuel utilisateur

Network Technologies

Network Technologies Xtendex USB-C5-200 Manuel utilisateur

Network Technologies

Network Technologies ST-C5USBD-250 Manuel utilisateur

Network Technologies

Network Technologies VOPEX-C5HDMI-4 Manuel utilisateur

Network Technologies

Network Technologies XTENDEX ST-C5KVM Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur