Netvox R718MBC Manuel utilisateur

Model：R718MBC

Wireless Activity Timer

R718MBC

User Manual

Table of Content

1. Introduction................................................................................................................................................................ 2

2. Appearance................................................................................................................................................................. 3

3. Main Features............................................................................................................................................................. 3

4.Set up Instruction.........................................................................................................................................................3

4.1 Power on and Turn on / off...............................................................................................................................3

4.2 Join Into LoRa Network...................................................................................................................................4

4.3 Function Key.................................................................................................................................................... 4

4.4 Data Report.......................................................................................................................................................4

5. Restore to Factory Setting.......................................................................................................................................... 5

6. Sleeping Mode............................................................................................................................................................5

7. Low Voltage Alarming............................................................................................................................................... 6

8. Installation.................................................................................................................................................................. 6

9. Important Maintenance Instruction............................................................................................................................ 6

10. Relevant Products.....................................................................................................................................................7

1. Introduction

The R718MBC series equipment is a vibration alarm device for Netvox ClassA type equipment

based on the LoRaWAN open protocol. It can count time of the movement or vibration duration of

the equipment and is compatible with the LoRaWAN protocol.

LoRa Wireless Technology:

LoRa is a wireless communication technology dedicated to long distance and low power

consumption. Compared with other communication methods, LoRa spread spectrum modulation

method greatly increases to expand the communication distance. Widely used in long-distance,

low-data wireless communications. For example, automatic meter reading, building automation

equipment, wireless security systems, industrial monitoring. Main features include small size, low

power consumption, transmission distance, anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure

interoperability between devices and gateways from different manufacturers.

2. Appearance

Fig.1 R718MBC Appearance

3. Main Features

Compatible with LoRaWAN protocol.

Powered by 2 x ER14505 3.6V Lithium AA battery

Easy set up and installation

Detectable voltage value and device movement status

4.Set up Instruction

4.1 Power on and Turn on / off

(1) Power on: open the battery cover; insert two sections of 3.6V ER14505 AA batteries and close

the battery cover.

(2) Turn on: if the device had never joined in any network or at factory setting mode, after

powering on, the device is at off mode by default setting. Press and hold function key for 3 seconds

till the green indicator flashes once and release to turn on device.

(3) Turn off: Press and hold function key for 5 seconds till the green indicator flashes quickly and

release. The green indicator will flash 20 times to show that the device is turned off.

Note:

1. The interval between shutting down twice or power off/on is suggested to be about 10 seconds to

avoid the interference of capacitor inductance and other energy storage components.

2. Do not press function key and insert batteries in the same time, otherwise, it will enter engineer

testing mode.

3. Once the battery is removed, the device is at off mode by default setting.

4. Turn off operation is same with “Restore to Factory Setting” operation.

4.2 Join Into LoRa Network

To join the device into LoRa network to communicate with LoRa gateway.

The network operation is as following:

(1) If the device had never joined any network, turn on the device; it will search an available LoRa

network to join. The green indicator will stay on for 5 seconds to show it joins into the network,

otherwise, the green indicator will be off.

(2) If R718MBC had been joined into a LoRa network, remove and insert the batteries; it will repeat

step (1).

4.3 Function Key

(1) Press and hold function key for 5 seconds to reset to factory setting. After restoring to

factory setting successfully, the green indicator will flashes quickly 20 times.

(2) Press function key to turn on the device which is in the network and the green indicator will flash

once and the device will send a data report.

4.4 Data Report

When the device is turned on, it will immediately send a version package and a cluster report data.

Data will be reported once per hour by default setting.

Maximum time: 3600s

Minimum time: 3600s (Detect the current voltage value every 3600s by default setting)

Default reportchange:

Battery ---- 0x01 (0.1V)

Note.

1. The device periodically sends data according to the maximum interval.

The data content is: R718MBC last vibration duration.

2. 718MBC device will only report according to minimum interval when battery voltage changes.

·R718MBC vibration times report:

The device detects sudden movement or vibration to start timing, and ends the time after entering the

stationary state for 5 seconds, sends a report of the vibration duration, and restarts a new round of

detection, and the timing is cleared. If vibration continues to occur during this process, the 5 seconds

timing restarts until it reaches a standstill.

·You can change the device type and Active vibration threshold by using the gateway to send

commands.

R718MB DeviceType (1Bytes, 0x01_R718MBA, 0x02_R718MBB, 0x03_R718MBC), the default

value is the programming value.

Active vibration threshold range is 0x0003-0x00FF (default is 0x0003)

Data report configuration and sending period are as following:

5. Restore to Factory Setting

R718MBC saves data including network key information, configuration information, etc. To restore

to factory setting, users need to execute below operations.

1. Press and hold function key for 5 seconds till the green indicator flashes and then release; LED

flashes quickly 20 times.

2. R718MBC is at off mode by default setting after restoring to factory setting.

Note: The device operation of turning off is the same as the “Restore Factory Settings” operation.

6. Sleeping Mode

R718MBC is designed to enter sleeping mode for power-saving in some situations:

(A) While the device is in the network → the sleeping period is Min Interval. (During this

period, if the reportchange is larger than setting value, it will wake up and send a data report).

(B) When it is not in the network → R718MBC will enter sleeping mode and wake up every

15 seconds to search a network to join in the first two minutes. After two minutes, it will wake

up every 15 minutes to request to join the network.

If it’s at (B) status, to prevent this unwanted power consumption, we recommend that users

remove the batteries to power off the device.

Min. Interval

(Unit:second)

Max. Interval

(Unit:second)

Reportable

Change

Current Change≥

Reportable Change

Current Change ＜

Reportable Change

Any number

between 1~65535

Any number

between 1~65535 Can not be 0. Report

per Min. Interval

Report

per Max. Interval

7. Low Voltage Alarming

The operating voltage threshold is 3.2V. If the battery voltage is lower than 3.2V, R718MBC will

send a low-power warning to the LoRa network.

8. Installation

This product comes with waterproof function. When using it, the back of it can be adsorbed on the

iron surface, or the two ends can be fixed to the wall with screws.

Note: To install the battery, use a screwdriver or similar tool to assist in opening the battery cover.

9. Important Maintenance Instruction

Your device is a product of superior design and craftsmanship and should be used with care. The

following suggestions will help you use the warranty service effectively.

• Keep the equipment dry. Rain, moisture, and various liquids or moisture may contain minerals that

can corrode electronic circuits. In case the device is wet, please dry it completely.

• Do not use or store in dusty or dirty areas. This can damage its detachable parts and electronic

components.

• Do not store in excessive heat. High temperatures can shorten the life of electronic devices, destroy

batteries, and deform or melt some plastic parts.

• Do not store in a cold place. Otherwise, when the temperature rises to normal temperature,

moisture will form inside, which will destroy the board.

• Do not throw, knock or shake the device. Rough handling of equipment can destroy internal circuit

boards and delicate structures.

• Do not wash with strong chemicals, detergents or strong detergents.

• Do not apply with paint. Smudges can block debris in detachable parts and affect normal operation.

• Do not throw the battery into a fire to prevent the battery from exploding. Damaged batteries may

also explode.

All of the above suggestions apply equally to your device, battery and accessories. If any device is

not working properly.

Please take it to the nearest authorized service facility for repair.

10. Relevant Products

Model Function Appearance

R718MBC Detect the movement or vibration of the

device and triggers an alarm.

R718MBC Counts the number of movements or

vibrations of the device.

R718MBC Counts the movement or vibration duration

of the device.

Autres manuels pour R718MBC

Table des matières

Autres manuels netvox Minuteur

netvox

netvox R718MBC Manuel utilisateur

netvox

netvox R311FC Manuel utilisateur

Manuels Minuteur populaires d'autres marques

Intermatic

Intermatic P1131 Manuel utilisateur

Learning Resources

Learning Resources Time Tracker mini Manuel utilisateur

CEBEK

CEBEK I-215 Manuel utilisateur

Somogyi

Somogyi home TS MD 5 Manuel utilisateur

Profile

Profile 010200280 Manuel utilisateur

Gizmo

Gizmo T4 Manuel utilisateur

Tekmar

Tekmar Timer 031 Manuel utilisateur

Daikin

Daikin DST301B61 Manuel utilisateur

sisel

sisel ENDA ETM2432 Manuel utilisateur

B&Q

B&Q TE103 Manuel d'utilisation et d'entretien

Hozelock

Hozelock AC Plus 2700 Manuel utilisateur

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Manuel utilisateur

Tork

Tork TU40 Manuel utilisateur

Emos

Emos EMT400F Manuel utilisateur

FarmTek

FarmTek Polaris Manuel utilisateur

Maximum

Maximum CRONUS Manuel utilisateur

Uberhaus

Uberhaus TD133B Manuel utilisateur

Clas Ohlson

Clas Ohlson 31-3766 Manuel utilisateur