Netvox R312 Manuel utilisateur

Model：R312

Wireless Doorbell Button

R312

User Manual

This document contains proprietary technical information which is the property of NETVOX

Technology. It shall be maintained in strict confidence and shall not be disclosed to other parties, in

whole or in part, without written permission of NETVOX Technology. The specifications are subject

to change without prior notice.

Table of Content

1. Introduction................................................................................................ 2

2. Appearance................................................................................................. 3

3. Main Features............................................................................................. 3

4. Set up Instruction....................................................................................... 4

5. Data Report ................................................................................................ 6

6. Installation.................................................................................................11

7. Important Maintenance Instruction.......................................................... 13

1. Introduction

The R312 is a doorbell button device for Netvox ClassA type devices based on the LoRaWAN open

protocol and is compatible with the LoRaWAN protocol.

LoRa Wireless Technology:

LoRa is a wireless communication technology famous for its long-distance transmission and low

power consumption. Compared with other communication methods, LoRa spread spectrum

modulation technique greatly extend the communication distance. It can be widely used in any use

case that requires long-distance and low-data wireless communications. For example, automatic

meter reading, building automation equipment, wireless security systems, industrial monitoring. It

has features like small size, low power consumption, long transmission distance, strong

anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure

interoperability between devices and gateways from different manufacturers.

2. Appearance

3. Main Features

Compatible with LoRaWAN

2 sections of 3V CR2450 button battery power supply

Doorbell status detection

Simple operation and setting

Protection class IP30

Compatible with LoRaWANTM Class A

Frequency hopping spread spectrum

Configuration parameters can be configured via a third-party software platform, data can be read

and alerts can be set via SMS text and email (optional)

Applicable to third-party platforms: Actility/ThingPark, TTN, MyDevices/Cayenne

Improved power management for longer battery life

Battery Life:

⁻Please refer to web: http://www.netvox.com.tw/electric/electric_calc.html

⁻At this website, users can find battery life time for various models at different

configurations.

1. Actual range may vary depending on environment.

2. Battery life is determined by sensor reporting frequency and other variables.

Doorbell Button

Function Key

Indicator

4. Set up Instruction

On/Off

Power on

Insert batteries (users may need a screwdriver to open)

Insert two sections of 3V CR2450 button batteries and close the battery

cover.

Note: Require 2 button batteries to supply power at the same time.

Turn on Press any function key and indicator flashes once meaning it is turned on

successfully.

Turn off

(Restore to factory setting)

Press and hold the function key for 5 seconds and green indicator flashes

20 times.

Power off Remove Batteries.

Note:

1. Remove and insert the battery; the device memorizes previous on/off

state by default.

2. On/off interval is suggested to be about 10 seconds to avoid the

interference of capacitor inductance and other energy storage

components.

3. If press any function key and insert batteries at the same time, it will

enter engineer testing mode.

Network Joining

Never joined the network

Turn on the device to search the network.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Had joined the network

(not restore to the factory setting)

Turn on the device to search the previous network.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Fail to join the network Suggest to check the device verification information on the gateway or

consult your platform server provider.

Function Key

Press and hold for 5 seconds

Restore to factory setting / Turn off

The green indicator flashes 20 times: success

The green indicator remains off: fail

Press once

The device is in the network: green indicator flashes once and sends a

report

The device is not in the network: green indicator remains off

Press doorbell button

Trigger the doorbell alarm

Note: Users can configure the button pressing time to send alarm by

command

Sleeping Mode

The device is on and in the

network

Sleeping period: Min Interval.

When the reportchange exceeds setting value or the state changes: send a

data report according to Min Interval.

Low Voltage Warning

Low Voltage 2.4V

5. Data Report

Report configuration and sending cycle are as follows:

Min Interval

(Unit:second)

Max Interval

(Unit:second) Reportable Change Current Change≥

Reportable Change

Current Change＜

Reportable Change

Any number

between 1~65535

Any number

between 1~65535 Can not be 0. Report

per Min Interval

Report

per Max Interval

The device will immediately send a version packet report along with an uplink packet including

doorbell alarm.

The device sends data in the default configuration before any configuration is done.

Default setting

Maximum time: 3600s

Minimum time: 3600s

BatteryChange: 0x01 (0.1V)

Doorbell button trigger:

Press the doorbell button and immediately send a report.

R312 was pressed, Alarm=1

R312 was not pressed, Alarm=0

Note:

1. The actual data sending cycle of the device is subject to the programming configuration

before shipment.

2. The interval between two reports must be the minimum time

The data report can be decoded by the Netvox LoraWAN Application Command

document and http://www.netvox.com.cn:8888/page/index

Example of ConfigureCmd

FPort：0x07

Bytes 1 1 Var (Fix =9 Bytes)

CmdID DeviceType NetvoxPayLoadData

CmdID– 1 byte

DeviceType– 1 byte – Device Type of Device

NetvoxPayLoadData– var bytes (Max=9bytes)

(1) Command Configuration:

MinTime = 1min、MaxTime = 1min、BatteryChange = 0.1v

Downlink：0155003C003C0100000000 003C(Hex) = 60(Dec)

Response：

8155000000000000000000（Configuration success）

8155010000000000000000（Configuration failure）

Description Device CmdID Device

Type NetvoxPayLoadData

Config

ReportReq

R312

0x01

0x55

MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

Battery

Change

(1byte Unit:0.1v)

Reserved

(4Bytes,Fixed

0x00)

Config

ReportRsp 0x81 Status

(0x00_success)

Reserved

(8Bytes,Fixed 0x00)

ReadConfig

ReportReq 0x02 Reserved

(9Bytes,Fixed 0x00)

ReadConfig

ReportRsp 0x82 MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

Battery

Change

(1byte Unit:0.1v)

Reserved

(4Bytes,Fixed

0x00)

(2) Read Configuration:

Downlink：0255000000000000000000

Response：8255003C003C0100000000（Current configuration）

Example of Button Press Time

FPort：0x0D

Default Press Time：0x00

(3) Command Configuration:

Trigger doorbell after press button 2 seconds

Downlink：0102 *Please notice port number is 0x0D (13) when downlink command

Response：

8100（Configuration success）

8101（Configuration failure）

(4) Read Configuration:

Downlink：02

Response：

8202（Current configuration）

Description

CmdID

PayLoad

(Fix byte,1byte)

SetButtonPressTimeReq 0x01

PressTime

(1byte,

0x00_QuickPush_Less then 1 Second,

0x01_1 Second push,

0x02_2 Seconds push,

0x03_3 Seconds push,

0x04_4 Seconds push,

0x05_5 Seconds push,

Other value is reserved)

SetButtonPressTimeRsp 0x81 Status

(0x00_Success

0x01_Failure)

GetButtonPressTimeReq 0x02

GetButtonPressTimeRsp 0x82

PressTime

(1byte,

0x00_QuickPush_Less then 1 Second,

0x01_1 Second push,

0x02_2 Seconds push,

0x03_3 Seconds push,

0x04_4 Seconds push,

0x05_5 Seconds push,

Other value is reserved)

Example for MinTime/MaxTime logic:

Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e.

BatteryVoltageChange=0.1V

MaxTime MaxTime

Sleeping(MinTime) Sleeping(MinTime)

Note: MaxTime=MinTime. Data will only be report according to MaxTime (MinTime) duration

regardless BtteryVoltageChange value.

Example#2 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e.

BatteryVoltageChange= 0.1V.

MaxTime

Sleeping(MinTime) sleeping sleeping sleeping

0H 15th M 30th M 45th M 1H

Wakes up and

collects data

2.8V

Does not report

Wakes up and

collects data

2.8V

Does not report

Wakes up and

collects data

REPORT 2.8V

Wake up and

collects data

REPORTS 2.8V

Wakes up and collects data

REPORTS 2.8V

Wakes up and collects data

REPORTS 2.8V

Wakes up and

collects data

2.8V

Does not report

Wakes up and

collects data

REPORT 2.8V

Table des matières

Autres manuels netvox Accessoires

netvox

netvox R313G Manuel utilisateur

netvox

netvox R718EB Manuel utilisateur

netvox

netvox R311CA Manuel utilisateur

netvox

netvox R718LB2 Manuel utilisateur

netvox

netvox R718PA Series Manuel utilisateur

netvox

netvox R718F2 Manuel utilisateur

netvox

netvox R718E Manuel utilisateur

netvox

netvox R718PB13 Manuel utilisateur

netvox

netvox RB11E Manuel utilisateur

netvox

netvox RA0730 Manuel utilisateur

netvox

netvox R718VB Manuel utilisateur

netvox

netvox R718G Manuel utilisateur

netvox

netvox R718PE Manuel utilisateur

netvox

netvox RA0711 Manuel utilisateur

netvox

netvox R718PB15A Manuel utilisateur

netvox

netvox ZB11C1 Manuel utilisateur

netvox

netvox R718A Manuel utilisateur

netvox

netvox R311G Manuel utilisateur

netvox

netvox R313DA Manuel utilisateur

netvox

netvox R311FA Manuel utilisateur

netvox

netvox R816B Manuel utilisateur

netvox

netvox R718F2 Manuel utilisateur

netvox

netvox Z809B Manuel utilisateur

netvox

netvox R311K Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

netvox R312 Manuel utilisateur

Manuels Accessoires populaires d'autres marques