Net2Edge LIB-306 Manuel utilisateur

LIB-306 Carrier Ethernet (CE)

Network Interface Device (NID)

Install Guide

Rev. D

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 2 of 25

Safety Warnings and Cautions

These products are not intended for use in life support products where failure of a product could reasonably be

expected to result in death or personal injury. Anyone using this product in such an application without express written

consent of an officer of Net2Edge does so at their own risk, and agrees to fully indemnify Net2Edge for any damages

that may result from such use or sale.

Attention: this product, like all electronic products, uses semiconductors that can be damaged by ESD

(electrostatic discarge). Always observe appropriate precautions when handling.

Warning: Potential for damage to equipment or personal injury.

Warning: Risk of Electrical Shock

Functional grounding point

Protective grounding point

Special considerations

LIB-306 Install Guide -

Record of Revisions

Rev

Date

Description of Changes

12th December 2014

Initial release for LIB-306 software v 2.0.x.

1st May 2015

Updated to v 2.1.3 which adds DDMI, HQoS, JSON, LLDP-MED, MEP BFD, MPLS-TP,

PFC, Traffic Test Loop, UDLD, and Y.1564 support.

25th September 2015

Update the Rack Mount Installation information.

26th January 2017

Re-Branded Manual

Trademark notice

All trademarks and registered trademarks are the property of their respective owners. All other products or

service names used in this publication are for identification purposes only, and may be trademarks or

registered trademarks of their respective companies. All other trademarks or registered trademarks

mentioned herein are the property of their respective holders.

by any means (graphic, electronic, or mechanical) without written permission from Net2Edge.

Address comments on this product or manual to:

Net2Edge

Kulite House, Stroudley Road,

Basingstoke, RG24 8UG, UK.

Tel: +44 345 0130030

E-Mail: support@net2edge.com

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 3 of 25

Table of Contents

Safety Warnings and Cautions......................................................................................................................2

1. Introduction.................................................................................................................................................4

Product Description.......................................................................................................................................4

Models...........................................................................................................................................................4

Applications...................................................................................................................................................4

Features........................................................................................................................................................6

Specifications................................................................................................................................................7

Related Manuals and Help............................................................................................................................7

2. Installation...................................................................................................................................................8

Unpacking / Package Contents.....................................................................................................................8

Install Cautions and Warnings......................................................................................................................8

Installation Location ......................................................................................................................................8

Rack Mount Installation.............................................................................................................................8

Grounding and Wiring Recommendations....................................................................................................9

Back Panel....................................................................................................................................................9

Front Panel..................................................................................................................................................10

Connecting Power.......................................................................................................................................12

Installing SFP Modules and Fiber Cables...................................................................................................13

Installing SFPs.........................................................................................................................................13

Installing Copper Cables.............................................................................................................................14

Copper Cable Configuration....................................................................................................................14

Connecting Ethernet Cables ...................................................................................................................14

Connecting Via the Serial CONSOLE / CLI................................................................................................15

Connecting Via the MGMT Port / Web GUI................................................................................................15

Factory Defaults..........................................................................................................................................16

Login using PuTTY Terminal Emulator Software........................................................................................16

Login Using Telnet......................................................................................................................................17

Login Using the Web Interface....................................................................................................................17

Re-Access the Web GUI via CLI Commands.............................................................................................17

Switching MGMT / PORT 1 Modes.............................................................................................................18

Configure the Default Management Port as a Data Port ........................................................................18

Product Registration....................................................................................................................................19

3. Troubleshooting .......................................................................................................................................19

4. Service, Warranty and Tech Support......................................................................................................22

Contact Us ..................................................................................................................................................22

Warranty......................................................................................................................................................22

One-Year Limited Hardware Warranty ...........................................................................................22

Return Authorization .........................................................................................................................22

Return Instructions.............................................................................................................................22

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 4 of 25

European Regulations.............................................................................................................................24

Electrical Safety Warnings..........................................................................................................................25

1. Introduction

Product Description

Net2Edge’s managed LIB-306 NID provides advanced packet performance metering and service creation

aimed directly at customer premises and cell sites. The LIB-306 is optimized for business Ethernet and

mobile backhaul deployments.

The LIB-306 is a multi-service NID that provides SLA assurance and advanced fault management that is

MEF CE2.0 compliant. IEEE 802.1ag Service OAM, ITU Y.1731 Performance Monitoring and IEEE 802.3ah

Link OAM are standard features.

The LIB-306 supports advanced features such as IPv6 and IPv4, VLANs, QoS, bandwidth allocation, ring

protection, jumbo frames and numerous security features. The LIB-306 can be managed and provisioned

with Net2Edge Converge™EMS or via Web, CLI and SNMP (v1, v2c & v3). The LIB-306 supports

SSL/SSH, RADIUS, TACACS+, Management VLAN and ACL rules.

The LIB-306 offers AC or DC power inputs for operation in a variety of environments. The SFP ports are

triple speed and support 100Mbps, 1000Mbps or SGMII SFPs. CWDM and Bi-Di SFPs are also supported,

allowing for flexible network architectures.

Models

The LIB-306 models are described below.

Model

Description

LIB-306-24

2xTP 4xSFP NID: Two 10/100/1000Mbps RJ45 ports with four 100/1000Mbps SFP

ports. Includes IEEE 1588v2 with RFC 2544 Traffic Generation.

LIB-306-42

4xTP 2xSFP NID: Four 10/100/1000Mbps RJ45 ports with two 100/1000Mbps SFP

ports. Includes IEEE 1588v2 with RFC 2544 Traffic Generation.

Applications

The LIB-306 is designed to support a wide range of MEF-based Carrier Ethernet services to include:

MEF CE 2.0 Certified Services (E-LINE, E-LAN, E-ACCESS, E-TREE)

Mobile Backhaul

Business Ethernet

Fiber to the Premise (FTTP)

SLA Enforcement Performance Statistics

Migration to Packet Networks

QoS for Differentiated Services

Several LIB-306 application examples are provided below.

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 5 of 25

CE Services Example

Cloud Services Example

E-LAN Services Example

E-Line Services Example

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 6 of 25

Features

Two/four 10/100/1000Mbps Base–T ports. Four/two 100/1000Mbps SFP ports. Any port can be

network (NNI) or client (UNI).

Two of the SFP ports support a proprietary 2.5Gbps mode.

TP ports support IEEE 802.3az Energy Efficient Ethernet for power saving.

Full bandwidth 1000Mbps switching, non blocking.

SNMP v1, v2c, and v3.

IPv6 and IPv4 support.

VLAN (802.1Q) Q-in-Q (C-Tag / S-Tag).

RMON and Syslog.

OAM Support: IEEE 802.3ah Link OAM, IEEE 802.1ag Service OAM, ITU-T Y.1731 Performance

Monitoring, and MEF E-LMI.

Loop Protection: ITU G.8032 and IEEE RSTP, MSTP.

G.8031 Linear Protection switching

IEEE 1588v2 PTP (Precision Time Protocol).

DC or AC power input (12VDC Barrel connector or 2-Pin, 21-60VDC Terminal block).

Jumbo Frame Support (10240 bytes maximum).

Wire speed loopbacks.

RFC 2544 Traffic Generation and Reports.

Last Gasp/Dying Gasp notification via SNMP trap. Monitor Rx and Tx Dying Gasp for each port.

SNMP traps configurable: System (Warm Start, Cold Start); Interface (Link Up. Link Down, LLDP);

AAA (Authentication Fail); Switch (STP, RMON).

Alarm inputs/outputs: RJ-45 connector with 2-IN and 2-OUT, 10-30VDC, 40mA maximum; optically

isolated from main board. Alarm indications via Syslog and SNMP.

E-LINE (EPL and EVPL) / E-LAN (EP-LAN and EVP-LAN) / E-ACCESS (ACCESS EPL and EVPL)

/ E-TREE (EP-TREE and EVP-TREE).

UNI or NNI configuration.

TOS (Type of Service) and Diffserv (Differentiated services).

QoS (802.1p Quality of Service): 8 queues; strict priority and DWRR, shaping, policing, P-bit and

DSCP.

Management via Industry standard CLI, Web, SSH/SSL & SNMP (v1, v2c, v3).

Port configuration, status, statistics, and monitoring.

RADIUS, TACACS+ and ACL.

Remote backup / restore configuration / firmware upgrades.

L2CP (Layer 2 Control Protocol).

LLDP (Link Layer Discovery Protocol).

Port Mirroring and Remote Mirroring.

Link Aggregation Control Protocol (LACP).

DDMI (Digital Diagnostics Monitoring Interface).

HQoS (Hierarchical Quality of Service) with Guaranteed Bandwidth Rate.

JSON (JavaScript Object Notation) RPC.

LLDP-MED per TIA-1057.

MEP BFDs (Bidirection Forwarding Detections).

MEP Route Trace.

MPLS-TP (Multiprotocol Label Switching).

PFC (802.1Qbb Priority Flow Control)

Traffic Test Loop (Y.1564, RFC2544, and TT-Loop functions).

UDLD (Uni Directional Link Detection) protocol support (RFC 5171).

Y.1564 Tests and Reports.

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 7 of 25

Specifications

Standards: IEEE 802.3 for 10Base-T, IEEE 802.3u for 100Base-TX IEEE 802.3z for 1000Base-X, IEEE

802.3ab for 1000Base-T, IEEE 802.3x for Flow control, IEEE 802.3ad for LACP, (Link Aggregation Control

Protocol) IEEE 802.1p for COS (Class of Service), IEEE 802.1Q for VLAN Tagging, IEEE 802.1w for RSTP

(Rapid Spanning Tree Protocol), IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol), IEEE 802.1x for

Authentication, IEEE 802.1AB for LLDP (Link Layer Discovery Protocol), IEEE 802.3ah Link OAM, IEEE

802.1ag SOAM FM, IEEE 1588-2008 (v2) Precision Time Protocol (PTP), ITU Y.1731 PM.

Maximum MAC Addresses: 8K

Maximum VLANs: 4K VLANs

Maximum Frame Size: 1518-10240 bytes including FCS.

Memory: 8Mbit shared buffer memory

Data Rate Copper ports: (RJ-45): 10/100/1000 Mbps. SFP ports (empty): 100/1000 Mbps or SGMII.

Status LEDs: Power, Port Activity and Port Duplex

Dimensions Width: Width: 190mm, Depth: 217mm, Height: 43.5mm

Weight: (excluding packaging) 1Kg

Input Power AC: 1 x 100-240 VAC; 47-63Hz Auto-sensing PSU

DC: 1 x -18VDC to -75VDC PSU

Power Consumption: nominal power measurements with all interfaces connected and active, using

standard 1G MM SFP modules:

Maximum power consumption 10 watts

Environment: Operating Temperature -20°C to +55°C, Storage Temperature -40°C to +70°C, Humidity 5-

85% non-condensing

Warranty: 1 Year Hardware warranty, 90 days Software warranty.

Support: Support packages available for Technical Support, Hardware Support, Training, and Consulting.

Related Manuals and Help

The LIB-306 ships with a printed documentation postcard that points you to the online product

documentation. The LIB-306 documentation set includes:

LIB-306 Install Guide (this manual)

LIB-306 Web User Guide

LIB-306 CLI Reference

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 8 of 25

2. Installation

Unpacking / Package Contents

Carefully unpack the contents and verify that you have received these items in the packaging:

One LIB-306 NID

One country specific AC power cord (specific country variant chosen at time of order)

Save the packaging for future use.

Install Cautions and Warnings

Warning: Risk of Electrical Shock. Disconnect power before installing the LIB-306. Failure to

observe this warning could result in an electrical shock.

CAUTION Only qualified persons should install the LIB-306. Failure to observe this caution could

result in poor performance or damage to the equipment.

CAUTION Install the LIB-306 in an operating environment where the temperature range is from

-20°C to +55°C, with relative humidity of 5% to 85% non-condensing. Failure to observe this caution could

result in poor equipment performance.

CAUTION DO NOT install the LIB-306 in areas where strong electromagnetic fields (EMF) exist.

Failure to observe this caution could result in poor equipment performance and data corruption.

WARNING Disconnect power before installing and wiring the LIB-306 for power. Failure to observe

this warning could result in an electrical shock.

Attention: this product, like all electronic products, uses semiconductors that can be damaged by

ESD (electrostatic discarge). Always observe appropriate precautions when handling.

Installation Location

Deciding where to install the LIB-306 can greatly affect its performance. When selecting an installation

location, consider the following:

Install the LIB-306 in a fairly cool and dry place. See the “Specifications” section (page 7) and the

cautions below for the acceptable temperature and humidity ranges.

Install the LIB-306 where it will not be exposed to liquid.

Install the LIB-306 in a location free from strong electromagnetic field generators (such as motors).

Do not expose or subject the LIB-306 to excessive vibration, dust, or direct exposure to sunlight.

Leave at least 5 cm (1.97 in) of space around the LIB-306 for ventilation purposes.

Rack Mount Installation

The LIB-306 can be rack mounted in a 19” rack via optional rack mount Kit.

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 9 of 25

Grounding and Wiring Recommendations

The LIB-306 can eliminate the effects of noise due to EMI via proper grounding. Always run the ground

connection from the ground screw to the grounded surface before connecting power.

The following wiring considerations are recommended:

Use separate paths to route wiring for power and device data cables. If power wiring and device

data cables must cross, make sure that the wires are perpendicular at the intersection points.

DO NOT run signal or communications wiring and power wiring in the same conduit. To avoid

interference, wire with different signal characteristics should be wired separately.

Keep input and output wires separated.

Label the wiring to all devices in the system for clarity.

No power ON/OFF Switch: The LIB-306 does not include a power ON/OFF switch; therefore, when power

is applied to the switch, it immediately powers Up.

Back Panel

The LIB-306 back panel is shown and described below.

RESET: The RESET button functions include:

1) Press and immediately release the RESET button to :

a. Restart the device.

2) Press and hold the RESET button for more than 5 seconds to:

a. Load the factory default configuration,

b. copy the running-configuration to the startup-configuration,

c. restart the device in factory default config.

d. Note that this resets the unit IP address.

The RESET button can be disabled (ignored) via the CLI. Refer to the LIB-306 CLI Reference manual.

Note: Restoring factory default can also be performed by making a physical loopback between port 1 and

port 2 within the first minute after switch reboot. In the first minute after boot, 'loopback' packets will be

transmitted at port 1. If a 'loopback' packet is received at port 2, then the switch will do a restore to defaults.

Press the Enter key to display the logon sequence, and then enter your User Name and Password.

DC INPUT:-18VDC to -75VDC PSU.

AC Input: 1 x 100-240 VAC; 47-63Hz Auto-sensing PSU

Net2Edge LIB-306 Install Guide

Install Guide Rev. D www.net2edge.com Page 10 of 25

Front Panel

The LIB-306 front panels are shown and described below.

MGMT / PORT 1: Port1 (MGMT) is a normal data port, but by default it will be in a

separate private VLAN (PVLAN 1) that you can remove. You can enable or disable out-

of-band management on PORT 1. PORT 1 can be optionally configured to support

either out-of-band management or it can be used as a normal data UNI/NNI port.

See Connecting Via the MGMT Port / Web GUI on page 15. By default, PORT 1 is enabled as a

Management port with a default IP and subnet mask. See Factory Defaults on page 16. Full instructions for

disabling the management function and how to use the port as a normal data port are provided in the CLI

Reference and Web User Guide manuals.See also Switching MGMT / PORT 1 Modes on page 18.

GigabitEthernet 1/1 (Port 1) is configured by default to act as a management port. This is achieved by

placing Port 1 in Private VLAN 6 which isolated traffic at layer 2 on this port from other front ports which are

by default placed into Private VLAN 1.

PORT 2 - PORT 4 (or PORT 1 & 2): Ethernet RJ-45 (10M/100M/1 Gbps) twisted pair ports (IEEE

10/100/1000Base-T interfaces). The Port 1 and Port 2 (or PORT 1-4) LEDs are shown and

described below:

LED1: Link/Activity/Duplex: ON = Link, OFF= No link

BLINK = Activity

Green = Full duplex, Yellow = Half duplex

LED2: Speed: Green = 1000Mbs, Yellow = 100Mbs, OFF = 10Mbs

PORT 5 & 6 (or PORT 3 - PORT 6 on the LIB-306-42): Two (or four) SGMII interfaces. The Serial Gigabit

Media-independent Interface (SGMII) interfaces can operate at multiple speeds of 100M/1G/2.5G bps.

P3 - P6 LED (P5 - P6 on the LIB-306-42): fiber link status. When lit in green,indicates a 1G fiber

link / activity. When lit in amber, indicates a 100M fiber link / activity. When off indicates no fiber

link established.

PWR LED: Green Power LED: On = power applied to the PC board. Flashes Green during LIB-306 boot up.

S1 LED: System Status LED (Bi-color Green and Amber):

During boot up –Amber

Normal operation –Green

Firmware upgrade –Flashes Green

Fatal condition logged –Flashes Amber

S2 LED: S2 is used for alarms. You can set the alarm severity to Info, Warning, or Error.

The severity is included in the alarm message and also sets the S2 LED color when the alarm is

triggered. The S2 LED is amber for an Info alarm, red for a Warning alarm, and blinking red for

an Error alarm. If not set, the default alarm severity is Info. See the back panel ALARMS port

Table des matières

Autres manuels Net2Edge Convertisseur de média

Net2Edge

Net2Edge PB-TDM1-CONTRA Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur