Net to Net Technologies UIM-E1 Manuel utilisateur

220-0000071 rev01

UIM-E1

E1 Uplink Interface Module

INSTALLATION

1. Unpack and inspect the equipment.

The following components should be included:

1 UIM-E1

4 #6 Phillips Panhead Internal Locking Screws

2 #6 Phillips Beige Flathead Screws

If there is any visible damage, do not attempt to connect the device. Contact Customer Support at 1-

877-638-2638 (001-603-427-0600 for international customers) or [email protected].

2. Verify switch configuration.

Ensure that the DIP switches on the UIM-E1 circuit board are positioned correctly (according to

desired configurations) prior to installing the UIM-E1 on a Multiplexer Uplink Module or in a Mini

DSLAM. There are eight DIP switches located on the top side of the circuit board, opposite the

faceplate. Switches are numbered from left to right, starting with Switch #1 on the left and ending

with Switch #8 on the right. Switches 1-2 and 5-8 are not used. Configuration for switches #3 and

#4 are as follows:

Frame Type & Line Coding

Switch Configuration

Installation Instructions

CAUTION Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when

handling this equipment.

Switch #3 Frame Type Switch #4 Line Coding

down CRC down HDB3

up no CRC up AMI

CRC = Cyclic Redundancy Check

HDB3 = High Density Bipolar 3

AMI = Alternate Mark Inversion

220-0000071 rev01

3. Install the UIM-E1.

Required tool for installation: Phillips screwdriver.

UIM-E1 Installation in an IP DSLAM

Affix the UIM-E1 to a Multiplexer Uplink Module (MUM).

a. Place the MUM on a flat surface with the circuit board facing up.

b. Select a port on the MUM for UIM-E1 installation; either port (1 or 2) may be used.

Although not required for operational purposes, if redundancy is desired, two UIMs

may be installed on the MUM, one in each port.

c. Remove the blanking plate* from the selected port.

d. Carefully slide the faceplate of the UIM-E1 under the lip of the MUM faceplate at

the selected port opening such that the UIM-E1 circuit board is facedown and the

UIM-E1 label shows through the port opening with the model name along the right-

hand edge.

e. Ensure the mounting holes on the UIM-E1 are lined up with the corresponding

pems on the MUM and the board-to-board connector key pins are properly aligned.

f. Gently press down with even pressure on all four corners of the UIM-E1 until the

board-to-board connector is fully seated.

g. Secure the boards together at the pems with the (4) provided panhead screws.

h. Secure the UIM-E1 faceplate to the MUM faceplate using the (2) provided beige

flathead screws.

Install the MUM in an IP DSLAM chassis.

The IPD12000 is a fourteen slot chassis; slots 1-12 are reserved for Access Modules

and slots 13-14 are reserved for Multiplexer Uplink Modules (MUMs). The IPD4000 is a

five slot chassis; slots 1-4 are reserved for Access Modules and slot 5 is reserved for a

MUM.

NOTE The UIM-E1 may be attached to a MUM that has already been in service, although you must

remove the MUM from the IP DSLAM in order to do so.

Removal of a MUM from an IP DSLAM chassis that is powered up will not

affect the operational status of other modules within the chassis;

it will, however, disengage the IP DSLAM's upstream network connection.

CAUTION *Blanking plates should be stored for possible future use. If a UIM-E1 is removed from a

MUM, it must be replaced with either another UIM or a blanking plate. DO NOT INSTALL A

MUM WITH AN EMPTY UIM PORT INTO AN IP DSLAM.

220-0000071 rev01

a. Align the MUM with the slot module guides of the chosen slot for installation

(either slot 13 or 14 on the IPD12000 or slot 5 on the IPD4000).

b. Slide the MUM firmly into the chassis. DO NOT USE EXCESS FORCE.

c. Tighten the fastening screws on the MUM faceplate.

d. Verify that the PWR (Power) LED on the MUM faceplate is illuminated.

UIM-E1 Installation in a Mini DSLAM

a. Remove the (8) screws securing the Mini DSLAM chassis and carefully lift off the chassis

cover. Set the screws aside.

b. Select a port on the Mini DSLAM for UIM-E1 installation; either port (1 or 2) may be used.

Although not required for operational purposes, if redundancy is desired, two UIMs may

be installed in the Mini DSLAM, one in each port.

c. Remove the blanking plate* from the selected port.

d. Carefully slide the faceplate of the UIM-E1 under the inside lip of the Mini DSLAM at the

selected port opening such that the UIM-E1 circuit board is facedown and the UIM-E1

label shows through the port opening with the model name along the right-hand edge.

e. Ensure the mounting holes on the UIM-E1 are lined up with the corresponding pems on

the Mini DSLAM board and the board-to-board connector key pins are properly aligned.

f. Gently press down with even pressure on all four corners of the UIM-E1 until the board-

to-board connector is fully seated.

g. Secure the boards together at the pems with the (4) provided panhead screws.

h. Secure the UIM-E1 faceplate to the front of the Mini DSLAM chassis using the (2)

provided beige flathead screws.

i. Replace the Mini DSLAM chassis cover and secure with the original (8) screws.

CAUTION Disconnect all power sources from the Mini DSLAM before installing the UIM-E1.

CAUTION *Blanking plates should be stored for possible future use. If a UIM-E1 is removed from a Mini

DSLAM, it must be replaced with either another UIM or a blanking plate. DO NOT OPERATE A MINI

DSLAM WITH AN EMPTY UIM PORT.

220-0000071 rev01

4. Connect the E1 Line.

Plug the E1 cable into the E1 RJ45 port on the UIM-E1 faceplate. Verify the connection; the E1 Lnk

LED will pulse (once per second) to indicate the E1 connection is established and operational.

Additional Information

LED Indicators

(A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid,

less constant rate.)

Regulatory Compliance

The following regulatory compliance information applies to the UIM-E1 as installed in a Mini DSLAM

chassis or as affixed to a MUM installed in an IP DSLAM chassis.

NOTE An E1 Uplink Interface Module (UIM-E1) must be connected via E1 line to an E1 network extender

provider unit (ENE2000-P or ENE2000-P-12-AC/DC). A UIM-E1 connected to an E1 network extender

subscriber unit (ENE2000-S) will not function.

E1 RJ45 Port Pinout

Pin 1 Rx Ring Pin 5 Tx Tip

Pin 2 Rx Tip Pin 6 not used

Pin 3 not used Pin 7 not used

Pin 4 Tx Ring Pin 8 not used

If you are using a shielded E1 cable

for your Network connection, it must

be grounded through Pins 3, 6, 7 & 8.

LED State Indication Additional Information

Lnk flashing

green E1 is operational The E1 connection has been established and traffic is flowing.

solid green E1 is operational A connection exists but there is indication of a problem with the E1

line.

illumination Loss of Synchronization

(LOS) The incoming connection to the UIM-E1 has been lost; no data is

being received.

Alm no

illumination E1 is operational Note: If the E1 Lnk LED also remains unlit then the UIM-E1 has

LOS.

solid amber Remote Alarm Indication

(RAI) The outgoing connection from the UIM-E1 has been lost; no data

is being transmitted.

pulsing

amber Alarm Indication Signal

(AIS) An indirect connection has been lost; the UIM-E1 may no longer

be receiving data.

220-0000071 rev01

European Regulatory Compliance Information for Class A Equipment

This Class A product complies with European Norm EN55022.

Warning: In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures to correct the situation.

220-0000071 rev01

™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc.

Worldwide Headquarters

Net to Net Technologies

112 Corporate Drive, Suite 1

Portsmouth, NH 03801

USA

+1 877-638-2638

http://www.NetToNet.com/

[email protected] EMEA Headquarters

Net to Net Technologies

Victoria House 19 Park Way

Newbury Berkshire RG14 1EE

+44 (0) 1635 570950

Table des matières

Autres manuels Net to Net Technologies Carte réseau

Net to Net Technologies

Net to Net Technologies UIM-DS3 Manuel utilisateur

Net to Net Technologies

Net to Net Technologies UIM-2T1 Manuel utilisateur

Net to Net Technologies

Net to Net Technologies UIM-E3 Manuel utilisateur

Net to Net Technologies

Net to Net Technologies UIM-T1 Manuel utilisateur

Net to Net Technologies

Net to Net Technologies UIM-2E1 Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur