Neostar Electronics SCA1 Manuel utilisateur

- 1 -

USER MANUAL

SCA1

Digital Terrestrial Receiver

and Recorder

- 2 -

1. Connections

After connecting the SCART to your TV please be

sure to select from your TV remote control the

key that allows you to select SCART source (could

be "AV" or "source" or "INPUT" or "SCART")

- 3 -

Remote Control

Key Function Key Function

POWER TV ON/OFF MUTE Audio Mute

0-9 Enter channel number or TV

setting into menu

TV/RADIO Switch between TV and Radio

EPG Electronic program guide AUDIO Select audio mode

←

PR Switch to previous program PAL/NTSC Switch between TV standard

INFO Info about current program MENU Show main menu

EXIT Exit from menu Freeze Picture / Pause when

used with Recording function

RECORD Start Recording STOP Stop Recording

UP/Down in item lists FAV Display favourite program list

CH+/CH- Change program or move

Up/Down in the Main menu

VOL+/VOL- Adjust the volume or move

LEFT/RIGHT in the Main menu

OK/LIST Confirm the selection inside

SUB Subtitle

Channel preview (9 windows) TXT Function not available

Switching functions in Main Menu

– red button services not

supported

AV/VGA AV output and VGA output

mode conversion

- 4 -

MAIN MENU

1. TV : View television and create a channel viewing list

2. RADIO : Listen to radio and create a listening list

3. MULTIMEDIA : Listen and watch video/audio/photos from your

external HD or USB memory using SD card slot or mini USB port,

or record to external memory devices (SD card, memory stick or hard drive)

4. GAME : Play games

5. SETUP : Scan available programmes, access recording options, user interface

and update the firmware

3. SETTING DVB-T FREEVIEW RECEPTION

3.1 Quick scan channels

Step1: Please press button, then press button,

Select “SETUP: Installation” press button.

Step2: OSD Language Setting

Step3: Country Setting

Step4: Then press and button to search for channels.

- 5 -

4.2. Full Installation

****** SEE PAGE 2 FOR HOW TO INSERT MEMORY CARD/USB

STICK, ANTENNA AND REMOTE CONTROL SENSOR ******

4.21.Setting Language

Users can select a preferred language among various languages in the Installation page.

(1) Press <menu> button to enter Main Menu.

(2) Press <VOL-/VOL+> button to select SETUP option.

(3) Press <CH+/CH-> button to select Installation option.

(4) Press <OK> button to enter Installation page.

(5) Press < CH+/CH- > button to select OSD Language option.

(6) Press < VOL-/VOL+ > button to select a language.

See Figure 1: If there is no channel database (from scan result) you may start at step 5

above.

Figure1. Main Menu, SETUP

- 6 -

Figure 2. Installation Page

4.22. How to receive TV programs?

Scan the broadcast frequencies and bandwidth to receive all programs.

(1) Press <menu> button to enter Main Menu.

(2) Press <VOL-/VOL+> button to select SETUP option.

(3) Press <CH+/CH-> button to select Installation option.

(4) Press <OK> button to enter Installation page.

(5) Press <CH+/CH-> button to select Country Setting option.

(6) Press <VOL-/VOL+> button to set Country Setting.

(7) Press <RED/GREEN> button to Auto Scan or Manual Scan.

See Figure 1 above: If there is no channel database (from scan result) you may start at

step 5 above.

4.23. Auto Scan

Auto Scan will first erase the entire existing channel list, and then scan default frequency

and bandwidth by Country Setting. After following steps at section 4.21:

- 7 -

(1) Press <RED> button to confirm to clear the database.

(2) Press <OK> button to confirm the database will be cleared and start Auto Scan.

It takes some time to do Auto Scan, user can press <exit> to exit at anytime. See below.

Figure 3. Clear database message

Figure 4. Auto Scan Page

- 8 -

4.24. Manual Scan

Manual Scan adds the new scanning results into the existing channel list - it doesn’t erase

the channel list. However, the user must know the Frequency and Bandwidth for scanning.

If the user scans the same Frequency and Bandwidth more than once, the programs will

be duplicated. After following steps at section 4.21:

(1) Press <GREEN> button to enter Manual Scan Page.

(2) Press <CH+/CH-> button to select Frequency option.

(3) Press <0~9> button to input the Frequency value.

(4) Press <CH+/CH-> button to select Bandwidth option.

(5) Press <VOL-/VOL+> button to set Bandwidth value.

(6) Press <OK/exit> button to start scan or exit. See Figures 5 and 6 below.

Figure 5. Manual Scan Page

- 9 -

Figure 6. Manual Scan Result

4. MULTIMEDIA

The Multimedia setting requires an SD card or USB port memory device (see page 2).

Enter ‘My Album’ and ‘My Music’, the screen will display “Initializing” when you insert a

memory device or “Device is not ready!” if the memory device is not yet

inserted/attached. See Figures 7&8

- 10 -

Figure 7. Multimedia

Figure 8. Device is not ready – replace external media device

Table des matières

Manuels Récepteur TV populaires d'autres marques

NEC

NEC PX-TUAN-01 Manuel utilisateur

Edision

Edision Piccollino Manuel utilisateur

Matsui

Matsui DTR1 Manuel utilisateur

Dyon

Dyon Raptor Manuel utilisateur

Strong

Strong SRT 2401 Mode d'emploi

TerraTec

TerraTec CINERGY DT USB XS DIVERSITY Manuel d'instructions

Haier

Haier 34F9K Manuel utilisateur

TechniSat

TechniSat DigiCom 1 Manuel utilisateur

Haier

Haier LT19A1 Manuel utilisateur

Triax

Triax CR 317 Manuel utilisateur

DirecTV

DirecTV D10-300 Manuel utilisateur

Motorola

Motorola VIP2502W Manuel utilisateur

ActionTec

ActionTec WirelessTV Manuel utilisateur

Motorola

Motorola VIP1200 Series Manuel utilisateur

Xoro

Xoro HRT 1300 Manuel utilisateur

Motorola

Motorola DH6200 Manuel utilisateur

Manhattan

Manhattan Plaza DS-100 Manuel utilisateur

Micro Prose

Micro Prose MPI-500 Manuel utilisateur