Neosens Skidsens Manuel utilisateur

Manual

SKIDSENS

Fouling Sensor

by Neosens

Quick User Manual

Installation Guide

Advantage Controls

P.O. Box 1472

Muskogee, OK 74402

Phone: 800-743-7431

Fax: 888-686-6212

www.advantagecontrols.com

email: [email protected]

3/2011

Specifications

Electrical:

• Input: 36 VDC @ 60mA

 • Output: 4-20mA(500Ω)

Environment:

• Ambient temperature - 0 to 180oF

 (withoutPVCadapter)

• Relative humidity - 0 to 100%

• Pressure - 80 PSI Max

Fouling Monitoring: 0-1mm(0to0.039in)

Accuracy: 1% of Full scale

Material: PVC(body)&316LSS(sensortip)

Connection: •Sensorsaresuppliedwitha1”(2.54cm)slipanda1”MNPTPVCquick

releaseadaptor.ThePVCadaptorhasamaximumtemperaturerating

of 125oF.

 •Peaksensorbodyhas1/2”straightBMPT

Shipping Weight: 4lbs(1.814kg)

Sensor Length: 9.375”(23.8cm)

Insertion Depth: Approx.3.375”(8.57cm)

Installation Notes

1. Install the sensor into flowing water for 30 minutes to allow the sensor to reach a temperature

equilibrium.

2. Sensor must have a minimum of 3.5 gpm flow across it.

3. Theanalogoutputisactiveandreferencedto+36Vdc.

4. If connected to a monitor with other 4-20mA inputs, they must be isolated from each other or this

input.ContactAdvantageControlsifaloopisolatorisrequired.

5. After the sensor has been installed and powered for 2 hours confirm that the output is a 4mA

signal.

Testing Sensor

If the sensor is giving a 3mA output after being installed for at least 2 hours in the minimum flow rate

of 3.5 gpm the following steps can be followed to test and reset the sensor’s operation.

1. Power OFF the Skidsens

2. AssumingtheSkidsenswasmaintainedinwaterwiththerequiredflowrate(>3.5gpm),powerON

the Skidsens and check the analog output reading during the first 20 seconds, as the probe will

be in test mode

a. For the first 10 seconds, the probe should display a 4mA signal

b. For the next 10 seconds, the probe should display a 20mA signal

3. After those initial 20 seconds, the probe will go to operational mode and should return to a 4mA

signal, or slightly above assuming the sensor has no fouling.

+--

4-20mA Probe Out

Sensor Input

RED

BLUE

WHITE

BROWN

GREEN (GND)

+--

36 VDC Signal

BLACK (HOT)

WHITE (NEU)

Power

SKIDSENS

Probe

Power Cord

J2-8

J2-1

J1-8

J1-1

4-20mA Input 1-

4-20mA Input 1+

4-20mA Input 2-

4-20mA Input 2+

4-20mA Input 3-

4-20mA Input 3+

4-20mA Input 4-

4-20mA Input 4+

4-20mA Input 5-

4-20mA Input 5+

4-20mA Input 6-

4-20mA Input 6+

LED

4-20mA Input Card

Note: The number of

channels or 4-20mA

inputs depends on

on the number ordered.

4-20mA Input 7+

4-20mA Input 7-

4-20mA Input 8+

4-20mA Input 8-

Wiring Diagram for MegaTron Connection

+--

4-20mA Probe OutPower

Sensor Input

RED

BLUE

WHITE

BROWN

GREEN (GND)

+--

36 VDC Signal

BLACK (HOT)

WHITE (NEU)

SKIDSENS

Probe

Power Cord

Input 1 -

Input 1 +

Input 2 -

Input 2 +

MegaTron SS

4-20mA Input

Rev D

Part # SS-MAI-2

Input 3 -

Input 3 +

Wiring Diagram for MegaTron SS Connection

Step 1:

First, push the SET UP RUN button to get this

screen. From here push the CUSTOMIZE (Button

4)togotothenextscreen.

>HOME SETUP<

SETPOINTS DATE/TIME

CALIBRATION CONFIGURE

TIMERS HISTORY

CUSTOMIZE WATER METER

ALARMS RELAYS

Step 2:

This is the Customize Screen. From here push

the mA IN(Button9)togotothenextscreen.

>CUSTOMIZE<

UNIT NAME

RELAY NAMES NOTEPAD

SYS NAME

INPUT NAMES mA IN

RUN SCREEN

Step 3:

This is the mA IN screen.  From here push

INPUT 1 OR 2(Button1or2)thengotothenext

screen.

>CUSTOMIZE mA INPUTS<

INPUT 1

INPUT 2

Step 4:

ThisistheCustomizemAInput1Screen.From

here push the NAME(Button1)togotothenext

screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

Step 5:

ThisistheCustomizemANamescreen.Fromhere

enterthenameofthemAInput(i.e.FOULING)

byusingtheArrowbuttons.ThenpressENTER

to confirm and return to the previous screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

Step 6:

From here push the UNITS(Button 2) togotothenext

screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

Step 7:

ThisistheCustomizemAUnitsscreen.Fromhereselect

the type of units (i.e. mm) by using the Arrow buttons.

ThenpressENTER to confirm and return to the previous

screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

Step 8:

From here push the NUMBER(Button3)togotothenext

screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

Step 9:

ThisistheCustomizemANumberFormatscreen.From

here select the number format (i.e. x.xxx) by using the

Arrowbuttons.ThenpressENTER to confirm and HOME

to return to the Home screen.

>CUSTOMIZE mA INPUT 1<

NAME FOULING

UNITS mm

NUMBER x.xxx

mA INPUT 1 NAME

[FOULING ]

USE ARROW KEYS TO CHANGE, PRESS

ENTER TO ACCEPT OR BACK TO ERASE

MegaTron Menus • Customize Setup

TYPE OF UNITS

-> mm

USE UP/DOWN KEYS TO CHANGE

PRESS ENTER TO ACCEPT

NUMBER FORMAT

-> X.XXX

USE UP/DOWN KEYS TO CHANGE

PRESS ENTER TO ACCEPT

Step 1:

First, push the SET UP RUN button to get this

screen. From here push the CALIBRATION

(Button2)togotothenextscreen.

>HOME SETUP<

SETPOINTS DATE/TIME

CALIBRATION CONFIGURE

TIMERS HISTORY

CUSTOMIZE WATER METER

ALARMS RELAYS

Step 2:

This is the Calibration Screen. From here push

the mA IN(Button7)togotothenextscreen.

>CALIBRATION<

SENSORS mA OUT

mA IN

Step 3:

ThisistheCurrenLoopCalibrationscreen.From

here push INPUT 1 OR 2(Button1or2)thengo

to the next screen.

>CURRENT LOOP CALIBRATION<

INPUT 1

INPUT 2

Step 4:

This is the mA Input Calibration Screen. From

here choose the MAX or MIN(Button3and4)to

go to the next screen.

>mA INPUT CALIBRATION<

20 mA 19649

4 mA 3913

MAX 1.000 mm

MIN 0.000 mm

OFFSET Enabled

Step 5:

ThisisthemAInputMAXscreen.Fromhereadjustthe

MAXreadingbyusingthenumberkeys(MAXshouldbe

set to 1.000 mm and MIN should be set to 0.000 mm).

ThenpressENTER to confirm and return to the previous

screen.

Note: All other mA Input Calibration settings can be

adjustedinthesamefashionbeginningatStep4.

>mA INPUT CALIBRATION<

20 mA 19649

4 mA 3913

MAX 1.000 mm

MIN 0.000 mm

OFFSET Enabled

mA INPUT 1 MAX (1.000 mm)

[_. ] mm

USE NUMBER KEYS TO CHANGE, PRESS

ENTER TO ACCEPT OR BACK TO ERASE

MegaTron Menus • Calibration Setup

Get the Advantage in Water Treatment Equipment

Advantage Controls can give you the Advantage in products, knowledge

and supportonallofyourwatertreatmentequipmentneeds.

 CoolingTowerControllers

 Boiler Blow Down Controllers

 Blow Down Valve Packages

 Solenoid Valves

 Water Meters

 Chemical Metering Pumps

 Corrosion Coupon Racks

 ChemicalSolutionTanks

 Solid Feed Systems

 FeedTimers

 FilterEquipment

 GlycolFeedSystems

 Pre Fabricated Systems

Get the Advantage

Table des matières

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur