Neomatica ADM34 Manuel utilisateur

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

This operation manual refers to the Tag ADM34 (Tag hereinafter), the manual describes its

functionality, the procedure of its configuration and operation.

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022 
 
Content 
Applicat ion  and fu ncti ons ................................................................................................................................................. 4
Technical  ch aracte rist ics .................................................................................................................................................. 4
Pr eparat ion  for u se an d con figu ratio n ..................................................................................................................... 5
1 Preparation for use ................................................................................................................................................................ 5
2.1 Search of the tag in application «ADM BLE-Configurator».................................................................................. 6
Configuration .............................................................................................................................................................................. 7
1 Configuration of the tag in "ADM BLE-Configurator" ............................................................................................7
2 Main parameters of the tag ......................................................................................................................................................7
2.1 Mode of operation ........................................................................................................................................................... 8
2.2 Submode ...........................................................................................................................................................................9
2.3 Data package control ..................................................................................................................................................... 9
2.4 Other configurations ...................................................................................................................................................... 9
3 Configuration of broadcast in the mode  «BLE tag»................................................................................................... 11 
4 Broadcast configuration in mode “Control of immobilizer”. .................................................................................... 13 
5 Broadcasting configuration in mode “Mixed”. ............................................................................................................. 15 
Tag firmware actualization ........................................................................................................................................................ 16 
Storage and Transportation ..................................................................................................................................................... 16 
Warranty ........................................................................................................................................................................................ 16 
Marking and Packing .................................................................................................................................................................. 17 
Disposal ......................................................................................................................................................................................... 17 
Scope of supply ......................................................................................................................................................................... 17 
Acceptance certificat e .................................................................................................................................................... 17 
 

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

1 Application and functions

The tag is designed to identify objects and persons.

The tag contains a microcontroller with integrated Bluetooth Low Energy 4.1 (BLE) radio

interface, two buttons, a LED and a sound transmitter. The tags is powered by a lithium battery

CR2450. The tag transmits the identification number according to the chosen algorithm through radio

channel using Bluetooth Low Energy 4.1 technology.

2 Technical characteristics

•Operating temperature: from 0°С up to + 40°С;

•Frequency range of radio interface: 2400..2483,5 МHz;

•Transmitter power: up to +8 dBm;

•Receiver sensitivity: -96 dBm;

•Data exchange technology: Bluetooth Low Energy (BLE);

•Coverage in the mode of BLE: up to 50 m in line-of-sight;

•Supported protocols: ADM, iBeacon, AltBeacon, Eddystone UID, Eddystone URL,

Eddystone EID, SOS.

•Battery: CR2450 Panasonic;

•Operation time with one battery: up to 1 year;

•Housing protection level: IP53 ;

•Housing material: ABS plastic;

•Dimensions, mm, not more than: 40x40x10 (without fob);

•Weight: not more than 20 g.

Figure 1 – View of the tag.

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

3 Preparation for use and configuration

3.1 Preparation for use

The tag is supplied switched with factory settings. By default continuous transmission is set,

the period of transmission is 1 second, the protocol is ADM.

3.2 Application «ADM BLE-Configurator»

Application «ADM BLE-Configurator» is available in Google Play.

To work with the application, you need the permission of the «Geolocation» or «Location». This

is due to Google requirements for applications that provide data exchange with BLE devices, since

BLE technology includes positioning by BLE beacons. You also need permission for the access of

photos, media and files because this is used when updating the sensor software.

The Android application «ADM BLE-Configurator» performs the following functions:

•Tag control;

•Tag configuration;

•Assessment of signal level when passing through obstacles;

•Assessment of the battery state;

•Definition of the tag address;

•Definition of the firmware version.

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

3.2.1 Search of the tag in application «ADM BLE-Configurator»

•Launch «ADM BLE-Configurator» application.

•Make sure that the application has been given all the necessary permissions.

•For correct operation, you need not only to permit the use of the «Geolocation» or «Location»,

but also to enable this function if it is disabled.

•The tag will be found as soon as the next message is sent.

If the tag is not detected, press both buttons at the same time and hold them not less than 10-

15 seconds before the beep, then try detecting again.

Following parametrs are avaliable:

•Model;

•MAC-address;

•RSSI –level of received radio signal

•The time passed since the last data mes-

sage was received

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

4 Configuration

The tag is supplied switched with factory settings. By default continuous transmission is set,

the period of transmission is 1 second, the protocol is ADM.

If default settings comply with the set goals, it is not necessary to make configuration.

Configuration is done in the application "ADM BLE-Configurator" in OS Android.

4.1Configuration of the tag in "ADM BLE-Configurator"

To check or change the tag settings, wait until it is detected and click on the icon

to go to the menu “Control”. If the tag is not detected, press both buttons at the same time and hold

them not less than 10-15 seconds before the beep, then try detecting again.

4.2 Main parameters of the tag

The tag configuration contains three levels that depend on each other. We recommend

setting three main parameters in the following order: mode of operation, submode, data package

control.

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

4.2.1 Mode of operation

Configuration of the main broadcast mode. This parameter determines what role the tag plays.

Following modes are:

•BLE Tag

•Immobilizer control – The tag makes works as remote control for the ADM33

immobilizer. It is possible to change the state of the immobilizer by buttons or by

presence/absence of signal.

•Mixed – device works as a tag and as remote control for immobilizer at the same time.

Broadcasting is carried out by pressing buttons or periodically. In this case, the

submode does not need to be selected. The broadcast algorithm is configured in the

menu “Data package control”.

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

4.2.2 Submode

Configuring the algorithm of message transmission on air. The availability of either submode.

depends on the mode of operation of the selected tag

Following submodes are avaliable:

•Continuous broadcast– broadcasting according to the established period.

•Continuous broadcasting with changing of the state - broadcasting according to the

established period with change of the identifier and broadcasting protocol by pressing

the button. A protocol and an identifier are set for each button.

•Broadcast by button – broadcasting starts after pressing the button and stops after the

set time has passed. Each button is set to the broadcast duration, protocol, and

identifier.

•Pressing the button turns broadcast on or off - broadcasting according to the established

period with ability to stop or continue broadcasting by button.

4.2.3 Data package control

Set the broadcast protocol and identifier. The availability of a particular item depends on the

selected submode.

Detailed description is given in paragraph 4.3.

4.2.4 Other configurations

•Password

Set password to protect configurations.

The password is required to run the session of the configurations.The existence of

password doesn’t affect tag.

• LED indication

Neomatica LLC”. Tag ADM34 ver..1.0 of 21.11.2022

Turn the light indication on or off.

• Sound indication

Turn the sound indication on or off.

•Battery power alert

Turn the battery power alert on or off.

•Potencia del transmisor

Setting transmitter power. The lower the power, the smaller the distance over which the signal

will be transmitted. Signal transmission range also depends on the surrounding conditions.

•Reset configurations

Resets the tag to factory settings.

•Firmware actualization

This menu updates the tag software.

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur