Neo Pro Delano Instructions de montage

Integrator’s Guide

delano™

HD Component Video Matrix Switch with Cat5 outputs

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

Table of Contents

Table of Contents....................................................................................3

Introduction.............................................................................................4

Features:..........................................................................................................4

Installation...............................................................................................5

Important Note Before Starting.......................................................................5

Unpacking.......................................................................................................5

Front Panel Protective Film ............................................................................6

Inputs ..............................................................................................................6

Outputs............................................................................................................6

Output Cabling................................................................................................ 6

RS-232 Serial..................................................................................................7

USB.................................................................................................................8

Rear Panel IR..................................................................................................8

Power..............................................................................................................8

Rack Mounting................................................................................................9

Operation.................................................................................................9

Overview.........................................................................................................9

Using the front panel.......................................................................................9

Controlling from an IR remote control .........................................................10

Party Mode Shortcut:................................................................................10

Last Command Feedback.....................................................................10

Setup Menu............................................................................................11

Setup:Panel LEDs.....................................................................................11

Setup:Disp Lamp......................................................................................11

Setup:AC Pwr...........................................................................................12

Setup:Touchpanel.....................................................................................12

Setup:TouchSense ....................................................................................12

Setup:TouchDelay....................................................................................12

Care and Maintenance..........................................................................13

Specifications.........................................................................................14

Performance..................................................................................................14

Power............................................................................................................14

Physical.........................................................................................................14

2 Year Warranty...................................................................................15

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

Introduction

Congratulations on your selection of the Delano HD Video Cat5

matrix switch.

Features:

• 8 inputs of component video (YpbPr)

• 16 outputs of component video

• High bandwidth video section (140 MHz) for 480i up to

1080p.

• Full non blocking matrix – any input to any output

• Attractive enclosure featuring brushed aluminum and high

gloss acrylic front, with silver top cover.

• Universal AC input power, 90-240VAC 50/60Hz with

standard IEC320 receptacle.

• All gold plated RCA connectors ensure a long life without

corroded connectors.

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

Installation

Important Note Before Starting

The Delano and the Hornet in wall receiver module (sold

separately) will only operate properly when all of the AC outlets

for the system and the displays in each zone are properly wired and

grounded.

Before installing anything, use an electrical outlet tester to verify

proper hot, neutral and ground wiring.

In the event your display has a two prong AC plug, it may be

necessary to connect the Hornet receiver’s bracket to AC ground of

the AC outlet. See the Hornet installation instructions for further

information.

The Delano Matrix Switch has vents on the sides of the chassis.

Although the Delano has no direct airflow requirements, do not

block these vents. It is OK to place other equipment directly on top

of or below the Delano.

The Delano is equipped with padded feet so it may be stacked on

top of other equipment without causing damage. In either case, to

avoid scratches, never slide equipment on top of one another. The

feet may be removed with a Phillips screwdriver to make the

chassis exactly 2RU in height.

Unpacking

The shipping carton for the Delano matrix switch will include the

following items:

1 – Delano Matrix Switch

1 – AC Power cord

1 – 6’ USB cable

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

1- 6’ RS-232 cable

1 – User’s Guide

1 – CD-ROM disc with USB drivers

1 – Pair of rack mount ears with screws

If accessories were ordered, the carton may also contain:

1 – IR remote control (optional)

Front Panel Protective Film

There is a clear film over the front panel to protect it during

manufacturing and shipping. Remove this film before using your

Delano matrix switch.

Inputs

Connecting source devices to the Delano can be done in any order.

All inputs have the same performance, so organize them as you see

fit. Just be sure to connect the video “Y”, “Pb” and “Pr” signals as

labeled on the rear panel.

Outputs

An output zone is made up of one Cat5 cable from the Delano. The

Hornet also has audio capabilities when used with the Concord

matrix switch, however with the Delano these features are not

utilized.

Output Cabling

In general, we have been referring to the cables as Cat5. The

minimum requirement for successful operation of the Delano

system is Cat5, but Cat5e is preferred. Cat6 may be used as long as

it is construct with 24 AWG wires. Most Cat6 is 24 AWG, but a 22

AWG variety does exist, and should not be used for this system.

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

Terminating the ends of the Cat5 cable can be done with either

TIA/EIA-568-B or A standard, so long as both ends are terminated

using the same standard. Below is the color codes for 568-B.

Although in some case of Ethernet where polarity of the pairs can

be swapped, with the Delano system each pair must be in the

correct order and polarity. A good practice is to use a cable tester

on each cable after termination to verify pin order before using the

cable.

Pin Color

1 White / Orange

2 Orange

3 White / Green

4 Blue

5 White / Blue

6 Green

7 White / Brown

8 Brown

Table 1: TIA/EIA-568-B wiring

RS-232 Serial

The serial port on the rear panel is labeled “RS-232”. It is wired as

a “DCE” device, which means it should be connected to a normal

PCs RS-232 port with a straight through cable. Connection to most

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

control systems should be with a straight through type serial cable,

such as the cable provided with the Delano.

For the command protocols, please refer to the manual entitled

“Integrator’s Guide to Serial Protocols”.

USB

If you plan to use the USB communication feature of the Delano,

connect the USB cable to the PC’s USB port (flat end), and the

other end (square end) to the Delano matrix switch.

Optionally you may choose to connect this cable later when you

are prepared to install the driver CD-ROM. Connecting the cable

will activate MS Windows plug and play wizard. On disconnect

and reboots, MS Windows will remember what COM port this

device was assigned.

Rear Panel IR

The rear panel connector labeled “IR” is for direct connection to a

control system. It is a 3.5mm 2 pin jack, and accepts unmodulated

IR. It is polarity insensitive, however normally the ‘tip’ is the

active signal, and the ‘sleeve’ is the ground.

Note: Some IR repeater systems are designed to work only with

their own IR blasters. Many integrators will cut these blaster cables

and add a 3.5mm plug on the end. In some cases this will work

fine, however some low end IR repeater systems will have too

much noise in their signal, and can prevent signals from being

properly decoded. Your results may vary.

Power

Once all the input and output connectors are in place, connect the

supplied power cable to the AC input. If you are not in North

America, you may use your own standard IEC320 power cable

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

with the Delano matrix switch. The Delano will detect whatever

voltage is supplied (from 90V to 240V AC), and adjust

accordingly.

Rack Mounting

The product ships with the rack mount ears detached from the unit.

This is to prevent damage to the chassis during shipment. Use the

supplied screws to attach the ears. The rack ears are universal, so

they fit on either side.

The chassis is a 2 rack units high only when the bottom feet are

removed. Removal requires a Philips screwdriver. Be careful when

turning over the unit as to not scratch the top paint.

Operation

Overview

The Delano is designed to be controlled form a third party control

system, either via RS232 or IR. The buttons on the front panel

allow the control of power and status feedback, however matrix

control must be performed from external sources.

Using the front panel

The 8x16 matrix switch’s front panel uses NeoTouch™

technology. This is different from many other front panels you

have seen with ‘membrane’ or ‘dome’ type buttons. The

NeoTouch™panel senses a human finger touching the acrylic

panel without any moving parts. For you, the user, this means that

you need not press hard to activate a button, a light tap will do.

Powering the 8x16 matrix switch on and off is accomplished by

pressing the power button. To prevent accidental power offs, two

button presses are required to shut down the matrix.

Delano Matrix Switch User’s Guide (DOC42-00022-A_NeoPro-Delano.doc)

In the normal powered on mode, the Fallbrook and Gillespie will

display the last command received. This is helpful for

troubleshooting your control sequences. If the last command

attempted was not received properly or was not formatted

correctly, it will not appear on the display.

You can also use the left/ right arrow keys and the select button to

access the setup menu. The setup options will be discussed in the

next section. Generally when you are presented with a choice on

the display, pressing select will toggle through the choices.

Changes in the matrix switch performance or features take place

right away, so changes do not need to be saved manually.

Controlling from an IR remote control

Controlling the matrix switch using IR follows the basic sequence

of:

#, Out, # # – Standard sequence for switching. Note that the

output number is always two digits, so output 1 is represented by

“01”

Party Mode Shortcut:

To route a single input program to all outputs, also known as party

mode, use the select key followed by the desired input:

Select, # Sends input # to all outputs

Last Command Feedback

The normal display shown on the front panel display can be

changed to the command feedback screen. This screen will display

the last received command, and is very helpful during control

system programming and debugging.

Table des matières

Autres manuels Neo Pro Commutateur matriciel

Neo Pro

Neo Pro JUNEAU Instructions de montage

Neo Pro

Neo Pro Imperial Instructions de montage

Neo Pro

Neo Pro BORREGO Instructions de montage

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

Kramer

Kramer XL 3216VS Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

Kramer

Kramer VP-2x2 Manuel utilisateur

Kramer

Kramer Sierra Video 6432V5xl Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Kramer

Kramer LASSEN XL 3232S Manuel utilisateur

Roland

Roland XS-1HD Manuel utilisateur

Kramer

Kramer VS-66HDCPxl Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes