Nedap Invexs M190 Instructions d'utilisation

Date: 21-03-2017 Version 8.0 Document no.: 5278210

This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does

the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be

reproduced in any way, in whole or in part, without the written consent of the publisher.

1. General

The Invexs 190 reader series is capable of reading (simultaneously) Nedap,

Mifare and DESFire credentials due to its dual reader technology. The

Invexs 190 is designed to be used on door pillars (mullion) and suitable for

outside and inside use. A model with keypad is also available. The Invexs

output can be set to either Wiegand, XS RF modulation or RS485 protocol

(plain or encrypted). Functionality and output are determined by the

configuration of the Invexs reader. The configuration is defined using the

programm AEreco, and deployed by the configuration card or via AEmon.

(More information about configurations can be found in Convexs Invexs

Installation Manual). Three LEDs (red, green, blue) and beeper are included.

LEDs around the keypad ciphers light up only in case a PIN code is

requested. The pigtail cable can be lead directly backwards or when using

the additional spacer (art. nr . 9949887) to the top or bottom.

2. Dimensions

3. Mounting Procedure Invexs

For mounting the Invexs 190, the mounting plate must be placed on the wall

first. For removing the mounting plate from the Invexs 190, unscrew the

screw (Torx, M5) at the bottom of the Invexs and push the Invexs 190

slightly up . The plate can be mounted using the 4 holes.Place the cable to

the correct position and replace the Invexs 190.

Invexs 190 Readers Mifare Nedap dual technology mullion readers

Quick Install sheet

Un screw

Push up

Mounting

plate

191

10 x 0.14

Shield

155

40 14.5

4 x 5

Dimensions: 191 x 50 x 30 mm.

4 mounting holes available at 32 x 155 mm

Cable pigtail: 10 x 0,14 mm shielded, 3m

Optional spacer (max thickness 10 mm) is

available for other cable outlet (top or

bottom)

Quick Install sheet | Invexs 190 Readers Mifare Nedap dual technology mullion readers

Version 8.0

SAM cover

4. Connections

Invexs is not hot-swappable, so when making/changing connections power must be switched

Off.

Wire

Colour

Function

Red

Power in (12-30VDC) /

XS modulator (120kHz)

Black

Power Ground / RF Ground

Grey

RS485 A (-)

Violet

RS485 B (+)

Green

Wiegand Data 0 (D0)

White

Wiegand Data 1 (D1)

Yellow

Beep input (BEEP)

Pink

UL LED input (UL*)

Blue

MD LED input (MD*)

Brown

NA LED input (NA*)

Shield / Metal

EM shield (connected to power ground)

•Cable shield (wire 11) must be connected to the metal case of the external device

•If connected to a 120kHz RF device (AEOS Nedap reader AEpack or XS device) the

power is supplied via the Convexs adapters (AX1014 for AEpacks, AB350 for XS

devices). Existing antenna cabling can then be reused for connecting the Invexs.

On the AX1014 an additional connection between GND (for UL and NA) and

Antenna GND must be made on the AX1014 (Invexs 190 has no separate cable

for this connection).

•UL*,NA*, MD* and BEEP are inputs for Open Collector to GND. If the Convexs

adapters are used, the original UL and NA signals are converted to the UL* and NA*.

5. LED Indicators Inside / Backside

There are two LEDs available: Blue for Status (of application), Green for Identification (both

visible behind the SAM cover at the back side)

6. LED Indicators Front

At the front a three colour LED is positioned at the middle of the Invexs

Depending on the used configuration the function of these LEDs can differ:

•Green LED:Card is been authorised (UL LED)

•Red LED:Card is not authorised (NA LED), controller is stand-by

•Blue LED:

Blinks fast: No configuration is available at this Invexs (present Configuration

card or load Configuration first).

Continuously ON: Determined by configuration: E.g. Reader stand-by.

(Blue LED is activated if UL is OFF and NA is more than 1 sec OFF)

GND

UL*/NA* / BEEP

ID (green)

Blinking

Card detected

ST: STATUS (blue)

Slow blinking

Application running (operating)

Fast blinking

Downloading or error during loading

2 short flashes

Application present but not active

3 short flashes

No application present

Quick Install sheet | Invexs 190 Readers Mifare Nedap dual technology mullion readers

Version 8.0

Function of LEDs and Beeper is controlled by used application settings of Invexs.

Green and Red LED can be controlled by hardware signals (wire 8 and 10) or RS485NR,

Blue LED indirectly by UL and NA, if this setting is activated (configuration) or by wire

9. Beeper can be controlled by hardware signal (wire 7), RS485NR or software

(configuration).

7. Firmware

Pay attention that the firmware loaded in the Invexs together with the Invexs type and

configuration determines functionality and protocols. Default (from factory) the Invexs handles

the credentials on several ways simultaneously:

•XS cards as: RS485NR, RF badge

•Mifare cards (CSN) as: RS485NR, RF data

The Invexs 190 requires dedicated firmware (not identical to the Invexs 170 firmware)

8. System Configurations (how to connect Invexs readers)

Configurations can be determined by the AEreco (loaded by AEmon or configuration

card)

Check the Convexs Invexs Installation Manual chapter 8 (Available reader Firmware) for

the compatibility for the used readers

Invexs uses existing antenna cabling

(Coax + 3*0,25qmm for LEDs).

On each AEpack

-RF interface an AX1014

must be added. Connections: see AX1014

RF interface AEpacks

Accessor III /

SimpleXS

AX1014

AB350

RF interface XS systems

Invexs uses existing antenna cabling

(Coax + 3*0,25qmm for LEDs).

On each XS reader

-RF interface an AB350

must be added. Connections: see AB350

To APx003 readers with RS485 special encrypted

protocol.

(LEDs, Beeper, Keys and Display are

controlled over the RS485 communication)

AEOS RS485 interface

- Third party systems

AEOS Wiegand

Wiegand interface

Wiegand output connected to Third party systems

(or to AEOS Wiegand interfaces). LEDs andBeeper

are controlled by hard wiring. (PINcode possible)

Quick Install sheet | Invexs 190 Readers Mifare Nedap dual technology mullion readers

Version 8.0

9. Tamper Switch

The Invexs 190 is equipped with a tamper switch which can be monitored over the RS485NR

protocol.

10. Beeper Indications

Beeper is also used for indication of loading the configuration:

•High sound beep (‘happy sound’): Configuration is loaded correct, second high sound

beep indicates that this configuration can be used with this Invexs

•Low sound beep (‘unhappy sound’): Configuration is not correct loaded or no

configuration available at start-up

SPECIFICATIONS Invexs 190: MD190 (article no.9948406), MND190 (article no.9948414), MDK190 (article no.9948457),

MNK190 (article no.9948449), MNDK190 (article no.9948465)

Discontinued products: M190 (article no. 9945512), MN190 (article no. 9948392), MK190 (article no. 9948422)

Dimensions:

191 x 50 x 30 mm

Weight:

± 350 gr

Protection:

IP65

Power Supply:

M(N)(D)190 12 – 30VDC, 60 - 24mA SELV

Power

Consumption:

60mA@12VDC, 35mA@24VDC

M(N)(D)K190 12 – 30VDC, 90 - 36mA SELV

90mA@12VDC, 45mA@24VDC

Environment:

Temperature: Operating:-30 – 65°C,

Storage:-30 – 65°C

Relative humidity:

10 – 93% non-condensing

Tamper switch:

Yes

Communication

RS485 (Encrypted AEOS protocol to APx003, (firmware APx003rs485NR). RS485 plain

Wiegand Data 0 and Data 1 (protocol depending on configuration)

RF Modulator (120 kHz for AX1014 or AB350)

Inputs:

Beeper (Beep ON / OFF, controlled by application) and Open collector to GND, max 20mA

UL*, NA*, MD* LED Open collector to GND, max 20mA

Indicators:

UL (green) NA (red) ,MD (blue)

Antennas

(internal):

Antenna 1: 120 kHz, Nedap XS compatible (PM and AM cards). Detection distance UniXS card: 8 cm

Antenna 2: 13,56 MHz, Mifare compatible Detection distance Mifare card: 4 cm

Mifare EV1 card: 2 cm

CABLE SPECIFICATIONS

10 wire shielded cable of approx. 3 meters length included (pig tail). Extensions can be made:

RS485:

2 x 2 x 0,25mm² shielded, max cable length: 1000 meter, cable capacity <= 100pF/meter

UL/GND/NA:

3 x 0,25mm², max cable length: 50 meter

XS MOD / GND:

Coax RG58U, max cable length: 50 meter

Or 5 x 0,25mm² shielded, max cable length: 50 meter, cable capacity <= 100pF/meter

Wiegand:

4 x 0,25mm² shielded (excl. LEDs), max cable length: 150 meter, depending on receiving device

MORE INFORMATION: Contact your local Nedap supplier or check our website www.nedapsecurity.com

Ce manuel convient aux modèles suivants

Autres manuels Nedap Système de sécurité

Nedap

Nedap Smartcard-Booster LEGIC Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur