Nedap ANPR LUMO Manuel utilisateur

www.nedapidentification.com

installation guide

2022-10-10 | v1.14 | Doc. no. 5286778

ANPR LUMO

ANPR LUMO | installation guide

2/45

not to be reproduced in any way, in whole or in part, without the written consent of Nedap N.V. All trademarks

referenced belong to their respective owners

Disclaimer

Nedap N.V. has made every effort to ensure the accuracy of the information contained in this document. However,

Nedap N.V. makes no representations or warranties whatsoever whether express or implied as to the accuracy,

correctness, completeness or fit-for-purpose or suitability for the purpose of this product. You use the products at your

own risk. Nedap N.V. excludes any liability to the maximum extent permitted by applicable law for the damages caused

by errors or failures made during the installation or improper use of this product or by not applying the instructions

stated in this document.

Nedap N.V. reserves the right to make improvements or amendments to this document and/or the products described

therein at any time without any notification. The latest version of this document can be found on our partner portal

https://portal.nedapidentification.com. Please download the latest version of this document and keep a copy for your

own records.

This document can be published in various languages but only the English language version will prevail. Nedap N.V.

assumes no responsibility for any errors caused for the translations into another language.

Warranty and spare parts

Please consult the Nedap products dealer from whom you purchased this product, in regards to the applicable warranty

conditions. This product cannot be used for any other purpose as described in this document. If the product is not

installed according to this document; the warranty provided is not applicable. At the sole discretion of Nedap N.V.,

Nedap N.V. may decide to change the conditions of the warranty policy. You agree that Nedap N.V. is able to

compensate you the pro-rata value of the warranty involved rather than replacing or repairing the product depending

on the technical or economical value of the product.

Prior to applying the warranty, please verify if you comply with the warranty conditions of the warranty policy, whether

you can successfully apply for the replacement or repair of a defective part. Parts can only be replaced with original

Nedap parts, otherwise the warranty policy will not be applicable on the product. If the warranty is applicable, please

contact the dealer or send the defective parts to the dealer.

Additional information

For any information or questions regarding the product, please contact your own dealer.

Nedap N.V.

Identification Systems

Parallelweg 2

7141 DC Groenlo

The Netherlands

+31 (0)544 471 111

[email protected]

www.nedapidentification.com

ANPR LUMO | installation guide

3/45

Contents

1Introduction ........................................................................................................................................................................ 6

1.1 Typical applications ................................................................................................................................................. 6

1.2 Key features ............................................................................................................................................................. 6

2Getting started .................................................................................................................................................................... 7

2.1 Mounting the ANPR LUMO....................................................................................................................................... 7

2.2 Connecting the ANPR............................................................................................................................................... 7

2.3 Assigning an IP-address.......................................................................................................................................... 7

2.4 Testing the ANPR ..................................................................................................................................................... 7

3Installation .......................................................................................................................................................................... 8

3.1 Safety precautions ................................................................................................................................................... 8

3.2 Mounting................................................................................................................................................................... 8

3.2.1 Pole mounting...................................................................................................................................................... 8

3.2.2 Behind barrier mounting ..................................................................................................................................... 9

3.3 Dimensions............................................................................................................................................................... 9

4Connections ...................................................................................................................................................................... 11

4.1 Ethernet connection .............................................................................................................................................. 11

4.2 Power supply.......................................................................................................................................................... 11

4.3 RS485 connection.................................................................................................................................................. 11

4.4 Wiegand connection .............................................................................................................................................. 11

4.5 Digital I/O ............................................................................................................................................................... 11

5OSDP.................................................................................................................................................................................. 12

5.1 Requirements......................................................................................................................................................... 12

5.2 Connections............................................................................................................................................................ 12

5.3 Configuration.......................................................................................................................................................... 12

5.4 Plate reading messages......................................................................................................................................... 12

5.5 Relay outputs ......................................................................................................................................................... 12

5.6 Digital inputs .......................................................................................................................................................... 13

5.7 OSDP capabilities................................................................................................................................................... 13

6Configuration..................................................................................................................................................................... 14

6.1 Using the web server ............................................................................................................................................. 14

6.2 Menu Items ............................................................................................................................................................ 15

6.2.1 Home.................................................................................................................................................................. 15

6.2.2 Text results ........................................................................................................................................................ 16

6.3 Access list............................................................................................................................................................... 17

ANPR LUMO | installation guide

4/45

6.3.1 Wiegand matchlist............................................................................................................................................. 19

7Configuration menus ........................................................................................................................................................ 21

7.1 CAMERA.................................................................................................................................................................. 21

7.2 ANPR....................................................................................................................................................................... 23

7.2.1 TRIGGER MODES............................................................................................................................................... 25

7.2.2 MODE OF OPERATION ...................................................................................................................................... 28

7.2.3 ENGINE .............................................................................................................................................................. 30

7.2.4 ACCESS .............................................................................................................................................................. 32

7.3 ACTIONS................................................................................................................................................................. 33

7.3.1 DIGITAL OUT ..................................................................................................................................................... 33

7.3.2 FTP UPLOAD ...................................................................................................................................................... 34

7.3.3 FTP DATABASE.................................................................................................................................................. 34

7.3.4 STORE ................................................................................................................................................................ 34

7.3.5 HTTP ACTION .................................................................................................................................................... 35

7.3.6 HMAC HTTP ACTION......................................................................................................................................... 35

7.3.7 TCP ACTION....................................................................................................................................................... 35

7.3.8 SERIAL ............................................................................................................................................................... 35

7.3.9 SERIAL OSDP..................................................................................................................................................... 36

7.3.10 MQTT ............................................................................................................................................................. 36

7.3.11 WIEGAND 26................................................................................................................................................. 36

7.3.12 WIEGAND 64................................................................................................................................................. 36

7.3.13 WIEGAND MATCHLIST ................................................................................................................................. 37

7.4 Installation parameters ......................................................................................................................................... 39

8SYSTEM SETTINGS ........................................................................................................................................................... 40

8.1 NETWORK............................................................................................................................................................... 40

8.1.1 NETWORK SETTINGS........................................................................................................................................ 40

8.1.2 TIME SETTINGS................................................................................................................................................. 40

8.2 USERS ..................................................................................................................................................................... 41

8.3 CLASSIFIER............................................................................................................................................................ 41

8.4 SYSTEM................................................................................................................................................................... 41

8.4.1 SYSTEM MANAGEMENT.................................................................................................................................... 41

8.4.2 LIBRARY VERSION ............................................................................................................................................ 43

8.4.3 DIGITAL IO ........................................................................................................................................................ 43

AMessage placeholders...................................................................................................................................................... 44

BDisposal of equipment...................................................................................................................................................... 45

CCE - UKCA declaration ...................................................................................................................................................... 45

ANPR LUMO | installation guide

5/45

DDocument revision............................................................................................................................................................ 45

ANPR LUMO | installation guide

6/45

1 Introduction

The NEDAP ANPR LUMO License Plate Reader offers automatic number plate reading. The NEDAP ANPR LUMO is an all

in one camera including camera, analyzer and IR illuminator. The ANPR has embedded processing software onboard.

The License Plate Reader is default featured with RS485, Wiegand and Ethernet communication.

1.1 Typical applications

Typical applications include parking, crime prevention, toll systems, security and access control, logistics and customs.

In addition the NEDAP ANPR LUMO can be applied in applications where it is difficult to issue RFID tags.

1.2 Key features

Automatic number plate reading.

All-in-one system including camera, analyzer, IR illuminator.

ANPR LUMO optimal performance in range from 2 to 10 meters.

Easy user configuration (web server).

TCP/IP Ethernet interface.

RS485 serial interface.

OSDP v2 supported including secure channel protocol.

Wiegand 26 bit/64 bit.

Wiegand match-list with custom Wiegand format.

Digital inputs.

Stand-alone operation supported by digital outputs and black-, white-, ignore list features.

Advanced access lists features through regular expressions.

Multiple regions of interest.

Power over Ethernet.

REST API.

ANPR LUMO | installation guide

7/45

2 Getting started

2.1 Mounting the ANPR LUMO

Determine how to mount the ANPR. The ANPR LUMO can be installed onto a pole or behind the barrier. Mount behind

the barrier to ensure recognition right in front of the barrier.

Important mounting issues are:

Best focus distance is between 2 and 10 meters [7 … 26 ft].

Angle between ANPR and number plate should be smaller than 25 degrees.

Mounting details are described in chapter 3.2.

2.2 Connecting the ANPR

The ANPR is delivered with 5m cables for power, I/O and network. Power supply, RS485 communication and I/O are

combined in one cable. Ethernet network is a separate cable. The cables are pre-fitted to the ANPR. For installation the

ANPR does not need to be opened. Connecting the power supply and network cable are required to configure the

ANPR.

2.3 Assigning an IP-address

Enter the default IP-address in the address bar of your web browser.

Default IP address is:

IP address: 192.168.3.15

The login window appears where the user is asked to type the username and password.

Username: admin

Password: secret

Go to the system configuration and setup the network configuration as desired. If required, now also other

configuration settings may be changed.

Note : The ANPR LUMO software interface is not compatible with Internet explorer

2.4 Testing the ANPR

Test the ANPR to check if it is aligned correctly and if it is able to read the license plates. Drive the vehicle into the

position where it should be possible to read its license plate.

Connect to the ANPR using your web browser on the main page you can see the live video. On the right side of the page

the text results are shown. It might be necessary to adjust the ANPR alignment.

ANPR LUMO | installation guide

8/45

3 Installation

3.1 Safety precautions

The following safety precautions must be observed during normal use, service and repair.

The ANPR shall be connected to safety ground.

Disconnect the power supply before removing any parts.

The ANPR shall only be installed and serviced by qualified and trained personnel.

To be sure of safety, do not modify or add anything other than mentioned in this manual or indicated by NEDAP

N.V.

CAUTION: for continued protection against risk of fire, replace fuses only with the same type and rating.

The ANPR can be powered from a low power, Class 2 power supply, in compliance with local regulations or

through PoE.

The product is to be connected only to PoE networks without routing to the outside plant.

The ANPR is equipped with an 850nm Infrared illuminator. The human eye will not or slightly see this light

coming from the illuminator. Do not look into the ANPR lens directly from close range or for more than 100

seconds. Eyes can be damaged by not taking these precautions. During normal use of the ANPR at a vehicle

gate, reading plates, there is no risk to the public.

3.2 Mounting

The ANPR is intended for vehicle access control. Vehicles are identified by the number plate when approaching the

gate. Because the number plate recognition is very fast, a full stop is normally not necessary. The ANPR covers a

reading distance of 2 to 8 meters. The field of view is typically one lane wide. There are 2 recommended positions for

the ANPR.

3.2.1 Pole mounting

The ANPR is positioned directly behind or in front of the actual barrier onto a pole. In that case the ANPR can be best

positioned on a pole at maximum 4 meter height. In this position the number plate of the vehicle directly in front of the

barrier cannot be read anymore. So these vehicles need to be recognized in flow. Mounting the ANPR at 4 meter height

is here the best option. When overhead installation is an option, the ANPR can at best be installed in the center of the

lane, above the lane. Horizontal angle will be 0° in that case, which is good.

Figure 1: Pole mounting (ANPR LUMO)

10 m 2 m 1 m 0 m

ANPR LUMO | installation guide

9/45

3.2.2 Behind barrier mounting

The ANPR is positioned behind the barrier at bumper height.

If there is space behind the barrier and the sight is not blocked, then the best place for the ANPR is at bumper height

(0.5m height) about 2 to 3 meters behind the barrier. A vehicle just in front of the barrier is still recognized in that case.

Figure 2: Behind the barrier mounting (ANPR LUMO)

3.3 Dimensions

Figure 3: ANPR housing dimensions

76.5

104

M6 (4x)

76.5

M4x12 (6x)

118

10 m 2 m 1 m 0 m

ANPR LUMO | installation guide

10/45

Figure 4: Mounting bracket dimensions

104

Ø7 (4x)

60° max

Autres manuels pour ANPR LUMO

Table des matières

Autres manuels Nedap Système RFID

Nedap

Nedap uPASS TARGET Manuel utilisateur

Nedap

Nedap MidRanger + Antenna Set Manuel utilisateur

Nedap

Nedap VP1007-B Manuel utilisateur

Nedap

Nedap NVITE Manuel utilisateur

Nedap

Nedap LibAssist Manuel utilisateur

Nedap

Nedap TRANSIT Entry Manuel utilisateur

Nedap

Nedap uPASS Access Manuel utilisateur

Nedap

Nedap Transit Ultimate Manuel utilisateur

Nedap

Nedap TRANSIT Manuel utilisateur

Nedap

Nedap PROX-BOOSTER 2G Manuel utilisateur

Nedap

Nedap uPASS REACH Manuel utilisateur

Nedap

Nedap TRANSIT Entry Manuel utilisateur

Manuels Système RFID populaires d'autres marques

Chainway

Chainway R1 Manuel utilisateur

IFM

IFM DTC600 Manuel utilisateur

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manuel utilisateur

RHOMBUS

RHOMBUS DR20 Manuel utilisateur

Sirit

Sirit IDentity 6204 Manuel utilisateur

SOREX

SOREX FLEX Manuel utilisateur

Omron

Omron V780-HMD68-EIP-KR Manuel utilisateur

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instructions d'utilisation

Shuttle

Shuttle BR06 Instructions d'utilisation

Digilock

Digilock Curve Keypad Basic Manuel utilisateur

Atid

Atid AT870 Manuel utilisateur

Chacon

Chacon 34958 Manuel utilisateur

Paxton

Paxton PROXIMITY architectural reader Manuel utilisateur

CipherLab

CipherLab 1800 series Manuel utilisateur

Brady

Brady FR22 Manuel utilisateur

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manuel utilisateur

Unitech

Unitech RH767 Manuel utilisateur

Honeywell

Honeywell 026366.00 Manuel utilisateur